PDi PDI-P14T2S User manual

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 1 of 59
PDI-P14T2S
Arm-Mounted, Healthcare-grade
LCD HDTV with Android
Document Number: PD196-377R1

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 2 of 59
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are
important operating and maintenance
instructions in the literature
accompanying this unit.
Overhead Falling Hazard
WARNING: To prevent injury, this apparatus must
be securely attached to the floor/wall in
accordance with the installation instructions. TV’s
can pose a striking hazard when mounted at an
elevated position. Use only PDi mounting brackets, support
arms, and appropriate hardware to assure TV will not fall from
the mounted position. Failure to do so may cause injury or
death.
Rain and Moisture
WARNING: To avoid the hazards of fire or
electrical shock, DO NOT expose this television to
rain or moisture or use in a wet location.
Oxygen Environment
WARNING: Do not use in any oxygen tent or
oxygen chamber. Such use may cause a fire
hazard.
Note to Cable TV Installer
This reminder is provided to call the cable TV systems
installer’s attention to Article 820-40 of the National Electrical
Code. The code provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of
the cable entry as practical. Canadian installations shall be
properly grounded in accordance with the Canadian Electrical
Code, Part 1.
FCC
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
Maintenance and Servicing
The TV does not require periodic maintenance other than
cleaning. Never remove the back cover of the TV; this can
expose you to high voltage and other hazards. If the TV does
not operate properly, unplug it and call an authorized service
center or PDi.
Cleaning and Disinfection
Clean the exterior of this television by removing dust with a lint-
free cloth. CAUTION: To avoid damage to the surface of the
television, do not use abrasive or chemical cleaning agents.
Spot test a new disinfectant by test cleaning a non-obvious
small spot on the TV’s back cabinet, keypad, and LCD panel.
Allow the disinfectant to soak per its instructions and then wipe
clean. Do not use the disinfectant if the TV’s surfaces show
any sign of discoloration or softening.
Product Modification
Do not attempt to modify this product in any way without
written authorization. Unauthorized modification could void the
user’s authority to operate this product.
Underwriters Laboratories
The model PDI-P14T Hospital Grade LCD HDTVTV is a
specialized TV and should be installed to National Electrical
Code specifications.
This device is safety tested and listed by the
Underwriters Laboratories as a product
suitable for use in health-care facilities in
both the United States and Canada.
Copyright,Trademarks
© 2014 PDi Communication Systems, Inc. All rights reserved.
PDi-TAB® is a registered trademark of PDi Communication
Systems, Inc. Product logos, brands and other trademarks
displayed within PDi’s products are the property of their
respective trademark holders, who are not affiliated with,
endorsing, or sponsoring PDi Communication Systems, Inc. or
our products.
Disclaimer
The author and publisher have used their best efforts in
preparing this manual. PDi Communication Systems, Inc.
makes no representation or warranties with respect to the
accuracy or completeness of the contents of this manual and
specifically disclaims any implied warranties or merchantability
or fitness for any particular purpose and shall in no event be
liable for any loss of profit or any other damages. The
information contained herein is believed accurate, but is not
warranted, and is subject to change without notice or
obligation.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 3 of 59
Danger chute d’objets
AVERTISSEMENT: Afin d’éviter toute blessure, cet
appareil doit être solidement fixé au sol/mur conformément
aux instructions d'installation. Les télévisions peuvent
présenter un risque de heurt lorsqu’elles sont montées en
position élevée. Utiliser uniquement des supports de
montage, des bras de support et le matériel approprié de
PDi afin d’assurer que la télévision ne tombe pas de sa
position de montage. Le non-respect de ces instructions peut causer des
blessures ou la mort.
Pluie et humidité
AVERTISSEMENT: Afin d’éviter les risques d'incendie ou
de choc électrique, NE PAS exposer cette télévision à la
pluie ou à l'humidité ou l’utiliser dans un endroit humide.
Environnement d'oxygène
AVERTISSEMENT: Ne pas utiliser dans une tente à oxygène ou
chambre à oxygène. Une telle utilisation peut causer un risque
d'incendie.
Remarque à l’intention des installateurs de câble TV
Le but de ce rappel est d’attirer l'attention de l’installateur de câble TV
sur l'article 820-40 du Code national de l'électricité. Le code fournit des
directives pour une mise à la terre appropriée et, précise que le câble de
mise à la terre doit être connecté au système de mise à la terre du
bâtiment, aussi près que possible du point d'entrée du câble dans le
mesure du possible. Les installations canadiennes doivent être
correctement mises à la terre conformément aux dispositions du Code
canadien de l'électricité, Partie 1.
FCC
Cet équipement a été testé et s'est avéré conforme aux limites pour un
appareil numérique de Classe A, conformément à la partie 15 des règles
de la FCC. Ces limites ont été conçues afin de fournir une protection
raisonnable contre les interférences nuisibles lorsque l'équipement est
utilisé dans un environnement résidentiel ou commercial. Si cet
équipement provoque des interférences nuisibles à la réception radio ou
télévision, ce qui peut être déterminé en éteignant et rallumant l’appareil,
l'utilisateur peut essayer de corriger l'interférence par une ou plusieurs
de
Réparations et entretien
Le téléviseur ne nécessite pas d’entretien périodique autre que le
nettoyage. Ne jamais retirer le couvercle arrière du téléviseur ; cela peut
vous exposer à des points de tension dangereuse ou à d'autres risques.
Si le téléviseur ne fonctionne pas correctement, le débrancher et appeler
un centre de service autorisé ou PDi.
Nettoyage et désinfection
Nettoyer l'extérieur de la télévision en enlevant la poussière avec un
chiffon non pelucheux. AVERTISSEMENT: afin d’éviter d'endommager
la surface de la télévision, ne pas utiliser de produits abrasifs ou
chimiques. Effectuer un test ponctuel avec un nouveau produit
désinfectant en nettoyant une petite surface non évidente à l’arrière du
meuble du téléviseur, sur le clavier et sur le panneau LCD. Laisser le
désinfectant tremper selon les instructions et puis essuyer. Ne pas
utiliser le désinfectant si les surfaces de la télévision révèlent un signe
de décoloration ou de ramollissement.
Modification du produit
Ne pas essayer de modifier ce produit de quelque façon que ce soit
sans une autorisation écrite. Toute modification non autorisée peut
annuler le droit de l'utilisateur à utiliser cet appareil.
Droit d'auteur
PDi Communication Systems, Inc. revendique des droits exclusifs sur le
contenu de ce manuel de l’utilisateur. Ce manuel a été rédigé à titre
d’information pour l'utilisateur et ne peut pas être utilisé pour fabriquer
tout élément montré ou décrit à l'intérieur. Droits d'auteur 2009-2014 par
PDi Communication Systems, Inc. Tous droits réservés.
Marques de commerce
Tous les noms de marques et noms de produits mentionnés dans ce
manuel sont des marques de commerce, des marques déposées ou des
noms commerciaux de leurs détenteurs respectifs. PDi et Better
Solutions Within Reach sont des marques déposées de PDi
Communication Systems, Inc., Springboro, Ohio, fabriqué sous licence
de Dolby Laboratories. Dolby et le symbole double-D sont des marques
déposées de Dolby Laboratories.
Underwriters Laboratories
Le modèle de télévision LCD HDTVTV, PDI-P14T de qualité hospitalière
est un appareil spécialisé et doit être installé selon les spécifications du
code national de l’électricité. Cet appareil a été testé quant à la sécurité
et homologué par Underwriters Laboratories comme un produit adapté
pour une utilisation dans les établissements de
santé aux États-Unis et au Canada

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 4 of 59
IMPORTANT SAFETY INSTRUCTIONS
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL
LOCAL CODES. READ AND FOLLOW THE SAFETY INSTRUCTIONS BEFORE ATTEMPTING THIS
INSTALLATION.
1. Read Instructions – All the safety and operating
instructions should be read before the product is
operated.
2. Keep these Instructions – The safety and operating
instructions should be retained for future reference.
3. Heed all Warnings – All warnings on the product and in
the operating instructions should be adhered to.
4. Follow all Instructions – All warnings on the product
and in the operating instructions should be followed.
5. Water and Moisture – Do not expose this product to
rain or moisture. Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub; in a wet basement; or near a swimming
pool; and the like.
6. Cleaning – Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Clean only with a dry cloth.
7. Ventilation – Slots and openings in the cabinet are
provided for ventilation to ensure reliable operation of
the product and to protect it from overheating. These
openings must not be blocked or covered. The
openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in
installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s
instructions have been adhered to.
8. Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
9. Power-Cord Protection – Protect the power cord from
being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit
from the product.
10. Attachments – Only use attachments/accessories
specified by the manufacturer.
11. Use only with cart, stand, tripod, bracket, or table
specified by the manufacturer, or
sold with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus
combination to avoid injury from
tip-over.
12. Lightning – For added protection for this product
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the product due to lightning and power-
line surges.
13. Servicing –Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
14. Oxygen Environment – Do not use in an oxygen
tent or oxygen chamber. Such use may cause a
fire hazard.
15. To prevent injury, this apparatus must be securely
attached to the wall in accordance with the
installation instructions. TV’s can pose a striking
hazard when mounted at an elevated level.
16. Power Sources – This product should be operated
only from the type of power source indicated on
the marking label. If you are not sure of the type of
power supply to your home, consult your product
dealer or local power company. For products
intended to operate from battery power, or other
sources, refer to the operating instructions.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 5 of 59
Table of Contents
Programming Menus and Setup ................................................................................................................................................8
Service Level..........................................................................................................................................................................8
Picture ....................................................................................................................................................................................8
Color Temperature..............................................................................................................................................................9
Noise Reduction .................................................................................................................................................................9
Sound .....................................................................................................................................................................................9
Balance...............................................................................................................................................................................9
Minimum Volume................................................................................................................................................................9
Maximum Volume.............................................................................................................................................................10
Power on Volume..............................................................................................................................................................10
Internal Speaker Enable...................................................................................................................................................10
HDMI Audio Ports.............................................................................................................................................................11
Composite Sound Mode ...................................................................................................................................................11
Volume Leveling ...............................................................................................................................................................11
Headphone Sound Mode..................................................................................................................................................11
Signal................................................................................................................................................................................12
Auto Program....................................................................................................................................................................12
Add / Delete Channels......................................................................................................................................................13
Clear Service Level...........................................................................................................................................................13
Copy Service Level...........................................................................................................................................................14
Parental Control................................................................................................................................................................14
TV Rating ......................................................................................................................................................................15
Television Rating Guides..............................................................................................................................................15
MPAA Rating ................................................................................................................................................................15
Change Password.........................................................................................................................................................16
Block Aux. Sources .......................................................................................................................................................16
Parental Lock Duration ................................................................................................................................................16
Parental Lock................................................................................................................................................................16
Power on Channel............................................................................................................................................................16
Channel Lock....................................................................................................................................................................17
Channel MemoryOverride................................................................................................................................................17
Pro:Idiom...........................................................................................................................................................................17
Features ...............................................................................................................................................................................17
Power on Caption Mode ...................................................................................................................................................17
Auto Power On/Lock.........................................................................................................................................................17

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 6 of 59
Inactive Power Off (h: mm)...............................................................................................................................................18
Bed A/B.............................................................................................................................................................................18
Caption Text Modes..........................................................................................................................................................18
Digital Captions.................................................................................................................................................................18
Digital Mode Time Setup...................................................................................................................................................19
Channel up Power Off.......................................................................................................................................................19
Channel to Other Source..................................................................................................................................................19
Power on ARC Mode........................................................................................................................................................19
Front Button Backlight.......................................................................................................................................................19
OSD Language (On-Screen Display) ...................................................................................................................................20
Sources ................................................................................................................................................................................20
Source Enable..................................................................................................................................................................20
Source Name....................................................................................................................................................................20
Power on Source ..............................................................................................................................................................20
System..................................................................................................................................................................................21
Diagnostics .......................................................................................................................................................................21
Reset to Factory Defaults .................................................................................................................................................21
Standby Power..................................................................................................................................................................21
USB Cloning and FW Update...........................................................................................................................................21
Restore Settings to TV..................................................................................................................................................21
Save Settings to USB ....................................................................................................................................................22
Upload Boot Code to TV...............................................................................................................................................22
Upload Firmware to TV ................................................................................................................................................22
Support.....................................................................................................................................................................................22
Android Setup ..........................................................................................................................................................................23
Interacting with Android - TOUCH & TYPE..............................................................................................................................23
Lock Screen..........................................................................................................................................................................23
Owner Profile ...........................................................................................................................................................................24
Setting up owner profile........................................................................................................................................................24
Pull Down Panels .................................................................................................................................................................26
Application Drawer ...............................................................................................................................................................26
Installing Android Applications.................................................................................................................................................27
Applications for the Administrator ............................................................................................................................................28
Settings.................................................................................................................................................................................28
Wireless and Networks.........................................................................................................................................................28
Wi-Fi..................................................................................................................................................................................28
Bluetooth...........................................................................................................................................................................30

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 7 of 59
Data Usage.......................................................................................................................................................................30
More…..............................................................................................................................................................................30
VPN (Virtual Private Network) .....................................................................................................................................31
Ethernet Configuration ................................................................................................................................................31
Device...................................................................................................................................................................................32
Sound................................................................................................................................................................................32
Display..............................................................................................................................................................................32
Storage .............................................................................................................................................................................33
Apps..................................................................................................................................................................................33
Users.................................................................................................................................................................................33
Personal ...............................................................................................................................................................................33
Location access................................................................................................................................................................33
Security.............................................................................................................................................................................34
Language & input..............................................................................................................................................................34
Backup & Reset................................................................................................................................................................34
Accounts...............................................................................................................................................................................34
Adding POP3 account.......................................................................................................................................................35
Adding Exchange account................................................................................................................................................35
System..................................................................................................................................................................................37
Date & Time......................................................................................................................................................................37
Accessibility......................................................................................................................................................................37
Over the Air (OTA)............................................................................................................................................................37
About tablet .......................................................................................................................................................................38
Media formats supported by Android................................................................................................................................39
Android Cloning....................................................................................................................................................................40
Copy Settings from Android – Master Configuration ........................................................................................................40
Restore Settings to Android – Slave Configuration ..........................................................................................................44
New User .................................................................................................................................................................................45
Home Screen........................................................................................................................................................................47
FAQ..........................................................................................................................................................................................51
Android Troubleshooting Tips..................................................................................................................................................56
Specs .......................................................................................................................................................................................58
Firmware..................................................................................................................................................................................58
Micro USB Cable......................................................................................................................................................................58
Limited Warranty......................................................................................................................................................................58

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 8 of 59
Programming Menus and Setup
Note: A programming remote control is required to perform all setup operations for the television. The programming
remote (Part Number PD108-420) is NOT packaged with the TV and must be ordered separately. The following
instructions assume you have a programming remote, have correctly mounted the TV, and connected a coax cable that
provides both power and RF signal.
Service Level
This TV offers a disable and three different programmable Service Levels: Free, Basic, and Premium. Only one Service
Level is usable at a time.
Disabled is like a mechanical keylock – when in Disabled service level, the TV can be turned OFF and ON, but cannot
be used for viewing. A standard message appears on a black screen.
Free lets patients watch hospital education and information
channels without renting the TV. The channels containing
programming for no charge are typically programmed into this
level of service. This is the factorydefault setting for service
level.
Basic service typically allows additional channels beyond
those offered in the FREE level.
Premium is the highest Service Level with typically the
most channels available for viewing.
Press the SETUP button to displaythe SETUP MODE menu.
Press the VOL► to disable or select desired service level.
(Free, Basic, Premium)
Picture
Adjustment of picture Brightness, Contrast, Color, Tint, Color Temperature and Sharpness is available to customize the
levels you prefer using the on-screen menus.
Brightness, Contrast, Color, Tint, and Sharpness
These settings have a range of 1-100. To change one of them, simply change the number by following this process.
Press the SETUP button to displaythe SETUP MODE
menu. Select the Picture menu item.
1. Press the CH▲/ CH▼buttons to highlight the desired picture item – Brightness, Contrast, Color, Color
Temperature, Sharpness, and Noise
Reduction.
2. Adjust the picture item using the VOL◄/ VOL►buttons to the desired level.
3. Press the SETUP button to store the picture values.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 9 of 59
Color Temperature
The color temperature menu adjusts the color balance of the picture.
“Standard”, “Reddish”, “Greenish”, “Bluish” color temperatures are
available for selection; however the individual colors are not adjustable.
The “USER” setting allows individual adjustment of each of the TV’s
primarycolors. The color temperature setting is best set using a
calibrated signal source capable of generating a test signal containing
both pure white and pure black picture components.
1. Enter the Picture menu
2. Press CH▲ / CH▼ to highlight Color Temperature.
3. Press VOL► to enter it.
4. Press CH▲ / CH▼ to see the individual settings.
5. On User, press VOL◄/ VOL► to highlight R,G, or B or to get
out of the customized adjustments.
6. Press CH▲ / CH▼ to adjust R,G, or B
Note: When you select one of the three colors to adjust, the
other two will turn gray.
7. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus disappear.
Noise Reduction
Additional picture improvementmaybe achieved by enabling the Noise
Reduction function found in the Picture menu.
1. Press the SETUP button to display the SETUP MODE menu.
2. Select the Picture menu item.
3. Press the CH▲/ CH▼buttons to highlight the Noise Reduction.
4. Use the VOL◄/ VOL►
bu ttons to alternate, Enable or Disable.
5. Press the SETUP button to return to the previous menu.
Sound
The Sound menu allows precise adjustment of several parameters.
1. Press the SETUP button to display the SETUP MODE menu.
2. Press the CH▲/ CH▼buttons to highlight the Sound menu item.
3. Use the VOL◄/ VOL►to displaythe Sound Menu.
Balance
This will adjust the volume balance of the left and right speakers.
1. In Sound menu, press the CH▲ / CH▼ to select Balance.
2. Press the VOL◄ / VOL► to select desired speaker balance from
L50 – R50 with 0 being equal balance.
3. Press SETUP to return to the preceding menu.
Minimum Volume
Sets the minimum volume level the TV can reach. Setting this to any
value other than 0 guarantees that some level of sound will always be
heard when the TV is operating.
4. In Sound menu, press the CH▲ / CH▼ to select Minimum
Volume.
5. Press the VOL◄ / VOL► to select your preferred minimum
volume.
6. Press SETUP to return to the preceding menu.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 10 of 59
Maximum Volume
Sets the maximum volume level the TV can reach.
1. In Sound menu, press the CH▲ / CH▼ button to select Maximum
Volume.
2. Press the VOL◄/ VOL►button to determine your preferred
maximum volume allowed.
3. Press the SETUP button to return to the preceding menu.
Power on Volume
This screen allows the setting of the initial volume for the TV upon powering on. Once the TV is on, the volume can be
set to any allowable level.
Note: If “Power on Volume” is set to LAST, and physical power is
removed, the TV will power on with a volume of zero.
1. In Sound menu, press the CH▲ / CH▼ button to select Power
on Volume.
2. Press the VOL◄/ VOL►button to determine your preferred
volume when the TV turns on. Setting the level to LAST causes
the TV to remember the last volume level used by the TV prior to
turning off.
3. Press the SETUP button to return to the preceding menu.
Internal Speaker Enable
The speaker’s inside the TV’s cabinet can be turned on or off for each TV
Service Level. Note: Sound to the earphone jack remains on at all times.
1. In the Sound menu, press CH▲ / CH▼ button to select the Internal Speaker Enable menu item.
2. Press VOL◄/ VOL►to enter the menu.
3. Press the CH▲/ CH▼ button to select the desired Service Level.
4. Press VOL◄/ VOL►to select Disable or Enabled.
5. Press the SETUP button to return to the preceding menu.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 11 of 59
HDMI Audio Ports
The HDMI1 Port has three settings: HDMI 1, PC, and Component. A
device connected to the HDMI ports can receive audio from one of these
sources.
1. In the Sound menu, press CH▲ / CH▼ to highlight HDMI1.
2. Press VOL◄ / VOL► to choose between HDMI and PC, or
Component.
3. Press SETUP to return to previous menu.
The second audio port can be between Component, Android, or PC.
Composite Sound Mode
The settings are L+R, L+L, and R+R
1. In the Sound menu, press CH▲ / CH▼ to highlight Composite
Sound Mode.
2. Press VOL ◄/ VOL ►to choose between settings.
3. Press SETUP to return to previous menu.
Volume Leveling
The settings can be adjusted from 50% to 100%
Headphone Sound Mode
The earphone jack sound can be used with either a mono (single ear) or
stereo (dual ear) style.
1. In the Sound menu, press CH▲ / CH▼ to highlight Headphone
Sound Mode.
2. Press VOL ◄/ VOL ►to choose between settings.
3. Press SETUP to return to previous menu.Channels
The Channels menu allows you to program different signal sources to either
disable or select from three Service Levels (Free, Basic, or Premium) and to
add or delete individual channels. It also allows you to block channels, TV
programs, movies, and auxiliary sources that can be input to the TV. Each
Service Level contains a different channel map.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 12 of 59
Signal
1. Press the SETUP button on the remote control.
2. Press CH▲ or CH▼ to highlight Channels.
3. Press VOL► to enter the Channels sub-menu.
4. Four different tuning types are available depending upon the healthcare facility’s signal type. Selection of the
correct signal type is required for the TV to recognize all possible channels and before any channel programming
can begin.
5. Enter the Channels menu
6. Press CH▲ or CH▼ to highlight Signal.
7. Press VOL ►to select Air, Cable STD, Cable IRC, or Cable HRC.
Note: Most hospitals use the Cable STD signal style.
Auto Program
The TV automaticallyscans each available channel for activity. Channels that display activity are memorized into the
selected Service Level.
Analog Only: TV searches for analog channels only.
Digital Only: TV searches for digital channels only.
Analog and Digital: TV searches for both analog and digital channels.
Interleave A+D: In the order of channel number regardless of the system.
All A then D: Digital channels are displayed after all analog channels.
1. From the Channels menu, select Auto Program
2. In the Auto Program menu, press the VOL► button to select Mode.
3. Press VOL► to set the scope of channel scanning.
4. Press the CH▼ button to select the Channel Sequence menu item.
5. Press ◄VOL►to set the Channel Sequence in which the channels are displayed after searching.
6. Press the CH▲ CH ▼ button to select the Service Level you wish to program. The menu displays the current
programming status of each level as either Programmed or Blank. Press the VOL► to choose the service level.
Note: A Programmed service level can also be reprogrammed if desired.
7. A confirmation menu will appear before proceeding. Press Yes▲to select YES and start auto programming. The
TV will now search all available channels with an on-screen progress percentage displayed. Once complete,
press the SETUP button to return to normal TV viewing.
Note: Any tuning mode that includes Digital channels will require several minutes to complete the auto
programming.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 13 of 59
Add / Delete Channels
Individual analog TV channels that are missing can be manually added to a Service Level. Or, analog TV channels that
require deletion can be manuallyremoved from a Service Level. Digital channels found during Auto Programming can be
enabled or disabled in each service level.
1. From the Channels menu, press the CH▲/ CH▼ to select Add/Delete Channels. Press VOL◄/ VOL► to
select.
2. Press CH▲ / CH▼ to select the Service Level you wish to add or delete channels.
3. Press VOL◄ / VOL► to enter the Add/Delete Channels menu for that Service Level.
4. Press CH▲ / CH▼ to select Analog Channel
5. Press VOL◄ / VOL► to scroll through everyavailable channel. The channel number changes to indicate the
current channel viewed.
6. Press CH▲ / CH▼ to select Add/Delete Analog Channel.
7. Press VOL◄ / VOL► to alternately Add or Delete the current Analog Channel from the Service Level.
8. Press CH▲ / CH▼ to select Enable/Disable Digital Channel.
9. A listing of all digital channels found during Auto Programming will be displayed.
NOTE: If the Enable/Disable Digital Channels states “no Channels”, either the TV did not locate any channels
during Auto Programming or the Mode was set to “Analog Only” during Auto Programming.
10. Press CH▲ / CH▼ to select a Digital Channel.
11. Press VOL◄ / VOL► to alternately Enable or Disable the current Digital Chanel from the Service Level.
12. Press SETUP to return to the previous menus.
Clear Service Level
This empties a service level of all its programmed channels, leaving it
blank.
1. From the Channels menu, press the CH▲/ CH▼ to highlight
Clear Service Level.
2. Press VOL► to select.
3. Press CH▲ / CH▼ to highlight the Service Level (Free, Basic,
or Premium).
4. Press VOL► to select the highlighted Service Level.
5. A confirmation page will appear. Press Yes▲to proceed.
Press ▼or SETUP to return to the previous menu.
Note: After a Service Level is cleared, the TV returns to the
Clear Service Level menu. “Blank” will appear to the right of
the Service Level.
6. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus disappear.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 14 of 59
Copy Service Level
Allows the copy of one service level’s channels to another.
1. In the Channels menu, Press CH▲ / CH▼to highlight Copy Service Level.
2. Press VOL► to select.
3. Press CH▲ to set the From Service Level. Press CH▼ to set the TO Service Level.
4. Press VOL ►to copy the Service Level.
5. A confirmation screen will appear. Press CH▲to proceed. Press CH▼or SETUP to return to the previous
menu.
Note: After a Service Level is copied, the TV returns to the Copy Service Level menu. If the To Service Level
has been set to active in the Service Level setting (see Service Levels on page 4), TV programming will appear.
6. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Parental Control
Parental Control allows you to block channels, TV shows, movies,
and devices that are connected to the P14W.
1. In the Channels menu, Press CH▲ / CH▼to highlight
Parental Control.
2. From the Parental Control menu, press VOL► to enter the
TV Rating menu.
3. Press CH▼ to move to one of the six age-based categories.
4. Press VOL◄ or VOL► to cycle through the sub-ratings
(ALL, FV, V, S, L or D) or exit out of the sub-categories in
that category. (See page 14 for rating guides)
Note: The U or B (unblocked or blocked) will turn red when
it is highlighted.
5. Press CH▲ or CH▼ to change the sub-rating.
6. Press the SETUP button to return to the previous menu. Or
press VOL◄ to get out of the sub-category.
Note: Categories that are rated for older audiences will be automatically blocked. If you block TV-Y category, then TV-Y7
will be blocked automatically. Similarly, if you block TV-G category, then TV-PG, TV-14 and TV-MA will also be blocked.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 15 of 59
TV Rating
This displays a list of parental TV viewing levels and allows for
Blocking or Unblocking of TV content.
1. From the Parental Control menu, enter the TV Rating menu.
2. Press CH ▲ or CH ▼to highlight a particular TV Rating.
3. Press VOL ◄or VOL ►to select Blocked or Unblocked.
4. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus disappear.
Television Rating Guides
Grade
Meaning
FV
Fantasy Violence
V
Violence
S
Sexual Situation
L
Adult Language
D
Sexual Suggestive Dialog
Guide
Meaning
TV-Y
Young Children
Content not offensive to most viewers
TV-Y7
Children 7 and over
Considered suitable for children over 7, may contain
Fantasy Violence Scenes
TV-G
General Audience
Considered suitable for all audiences; children may watch
unattended
TV-PG
Parental Guidance
Suggested Unsuitable for younger children, may contain;
Suggestive Dialog, Bad Language, Sex, and Violence
Scenes
TV-14
Parents Strongly
Cautioned
Unsuitable for children under 14, may contain; Strong
Dialog, Bad Language, Sex, and Violence Scenes.
TV-MA
Mature Audience Only
Adults only, may contain; Strong Dialog, Bad Language,
Sex, and Violence Scenes
MPAA Rating
Most televised movies are now rated. MPAA Rating selectivelyallows the TV to only present movie content that is
unblocked per its preset level.
5. From the Parental Control menu, enter the MPAA Rating
menu.
6. Press CH ▲ or CH ▼to highlight a particular MPAA Rating.
7. Press VOL ◄or VOL ►to select Blocked or Unblocked.
8. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus
disappear.
Note: Parental Control will automatically block any category that is
rated for older audiences. For example, if you block the PG-13
category, then R, NC-17 and X will be automatically blocked also.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 16 of 59
Change Password
The Parental Control access password can be changed using this
menu.
Note: The factory default password that is programmed into the TV is
0000.
Block Aux. Sources
Like TV programs and channels, the auxiliary sources can be blocked
too. When the TV encounters an external signal source that is not
appropriate per its settings, a black screen appears with muted sound.
Note: Parental Lock must be enabled for the sources to be blocked.
1. In the Parental Control menu, press CH ▲or CH ▼to highlight
Aux. Block Source.
2. Press VOL ◄or VOL ►to select Unblocked or Blocked.
3. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus disappear.
Parental Lock Duration
This sets how long an enabled Parental Lock will be active.
1. In the Parental Control menu, press CH ▲or CH ▼to highlight
Parental Lock Duration.
2. Press VOL ◄or VOL ►to select the desired number of hours
(1-99) or Always.
3. Press the SETUP button to return to the previous menu. To
exit, press SETUP until the programming menus disappear.
Parental Lock
This enables or disables the settings in the Parental Control menu.
Enabling it will require the password to be entered to access the
Parental Control menu in the future.
1. In the Parental Control menu, press CH ▲or CH ▼to highlight
Parental Lock.
2. Press VOL ◄or VOL ►to select Enable or Disable.
3. Press the SETUP button to return to the previous menu. To exit,
press SETUP until the programmingmenus disappear.
Power on Channel
Displays a certain channel each time the TV is turned on. This feature
is useful for hospitals that have a Welcome Channel and wish to have it
displayed upon initial use of the TV. The patient can then tune to any
other available channel.
1. Enter the Channels menu
2. Press CH ▲ or CH ▼to highlight Power on Channel.
3. Press VOL ►to select it.
4. Press CH ▲ or CH ▼to highlight the desired Service Level
(Free, Basic, or Premium).
5. Press VOL ◄or VOL ►to select one of the channels currently
available in the Service Level or Last.
NOTE: Last will cause the TV to turn on to the last channel
before it was turned off.
6. Press the SETUP button to return to the previous menu. To
exit, press SETUP until the programming menus disappear.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 17 of 59
Channel Lock
Locks the currently viewed channel and prevents patients from tuning to any other channel. This feature is useful when
the TV is used for information display purposes.
1. Enter the Channels menu
2. Press CH ▲ or CH ▼to highlight Channel Lock.
3. Press VOL ◄or VOL ►to select Enable or Disable.
4. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programmingmenus
disappear.
Channel Memory Override
Allows a channel to be entered with the remote’s number buttons that is not memorized in the current service level.
1. Enter the Channels menu
2. Press CH ▲ or CH ▼to highlight Channel MemoryOverride.
3. Press VOL ◄or VOL ►to select Enabled or Disabled.
• DISABLED = Service Level Channels only.
• ENABLED = All possible channels.
4. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programmingmenus
disappear.
Pro:Idiom
MTI port is used with Lodgenet, otherwise use Free to Guest
Features
The Features menu provides adjustable settings that customize the TV to your hospital.
1. Press the SETUP button.
2. Press CH▲ or CH▼ to highlight Features.
3. Press VOL► to enter the Features sub-menu.
Power on Caption Mode
Power on Caption Mode memorizes the caption setting upon powering
the TV off. With this feature set to off, the TV will always power on with
the captions disabled. With this feature set to Last, the TV turns on
with the last caption setting enabled.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Power on Caption Mode.
3. Press VOL◄ or VOL► to select Last or Off.
4. Press the SETUP button to return to the previous menu. To
exit, press SETUP until the programming menus disappear.
Auto Power On/Lock
The TV will turn on and stay on whenever electrical power is applied to the set. The feature is useful for controlling the TV
from a wall switch or preventing the TV from being turned off by the TV power button or the remote control.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Auto Power On.
3. Press VOL◄ or VOL► to select Disabled or Enabled.
4. Press the SETUP button to return to the previous menu.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 18 of 59
Inactive Power Off (h: mm)
1. The TV will automaticallypower off after a specific period of viewer inactivity providing energy savings.
2. Enter the Features menu
3. Press CH▲ or CH▼ to highlight Power Management.
4. Press VOL◄ or VOL► to select an active time or select Disabled to disable this feature.
5. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programmingmenus
disappear.
Note: Auto Power On must be set to Disabled for this function to operate.
Bed A/B
The TV can be controlled by a patient IR remote. The TV offers Bed A and Bed B selectable codes for independent
control of a single television in a two television room. The patient remote can be toggled between Bed A and Bed B codes
by pressing (using a paperclip) the CODE button on the remote.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Bed A/B.
3. Press VOL◄ or VOL► to select A or B.
4. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programmingmenus
disappear.
Caption Text Modes
Teletext can be displayed in addition to Captions. Teletext is not normallybroadcast in the USA. Caption Text Modes
should be set to Disabled for TVs operated in the USA.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Caption Text Modes.
3. Press VOL◄ or VOL► to select Disabled or Enabled.
4. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Digital Captions
Customization of Closed Captions on ATSC/QAM channels.
1. Enter the Features menu
2. Press CH ▲ or CH ▼to highlight Digital Captions.
3. Press VOL ►to select it.
4. Press CH ▲ or CH ▼to highlight the attribute you wish to change.
5. Press VOL ►to change it. (See the table below for the settings of
each attribute.)
6. Press SETUP to return to the previous menu. To exit, press SETUP
until the programmingmenus disappear.
Attribute
Settings
Font Size
Small, Standard, Large, Default
Font Style
Style0 – Style 7, Default
Foreground Color
White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default
Background Color
White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default
Edge Color
White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default
Foreground Opacity
Solid, Translucent, Transparent, Flashing, Default
Background Opacity
Solid, Translucent, Transparent, Flashing, Default
Edge Style
None, Raised, Depressed, Uniform, Left Drop
Shadow, Right Drop Shadow, Default

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 19 of 59
Digital Mode Time Setup
The current time will be set automaticallyfrom a digital channel signal
provided by a broadcasting TV station.
1. Enter the Features menu
2. Press CH ▲ or CH ▼to highlight Digital Mode Time Setup
3. Press VOL ►to select it.
4. Press CH ◄or CH ►to select your viewing area time zone:
Pacific, Alaska, Hawaii, Newfoundland, Atlantic, Eastern,
Central or Mountain.
5. Press VOL ▲or VOL ▼ to highlight Daylight Savings.
6. Press CH ◄or CH ►to select Auto, On, or Off depending on
whether or not your viewing area observes Daylight Savings
Time.
7. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus
disappear.
Channel up Power Off
This feature causes the TV to turn off once it reaches the highest numbered (last) channel and is usually used with single
button style pillow speakers.When the feature is disabled, the TV will continue on to the lowest channel and not turn off.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Channel Up Power Off.
3. Press VOL ◄or VOL ►to select Enabled or Disabled.
4. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Channel to Other Source
External signal sources connected to the TV, such as DVD players or video-game systems, are shown in the current
channel lineup after the highest channel and then shown on the TV. Set this feature to Disabled to require the activation of
the external sources by pressing the remote’s or the TV’s TV/AV button. Set this feature to Enabled to allow access to
external devices by pressing channel up or down buttons on a remote or most pillow speakers.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Channel to Other Source.
3. Press VOL ◄or VOL ►to select Enabled or Disabled.
4. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Power on ARC Mode
The TV powers on with a set screen sized aspect ratio of 4:3, 14:9, 16:9, 16:9 Panorama, or Last.
1. Enter the Features menu
2. Press CH▲ or CH▼ to highlight Power On ARC Mode.
3. Press VOL ►to select 4:3, 14:9, 16:9, 16:9 Panorama, or Last.
4. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Front Button Backlight
Normal Brightness (How bright you would like the backlight at all times)
Active Brightness (How bright you would like the backlight when touched)
Each of these may be adjusted from 0-100.

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Document No: PD196-377R1 PDI-P14T2S LCD HDTV with Android Page 20 of 59
OSD Language (On-Screen Display)
You can select the language you wish to use in your on-screen displays..
1. Press SETUP.
2. Press CH▲ or CH▼ to select the OSD Language menu.
3. Press VOL ◄or VOL ►to select your desired language.
4. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Sources
Source Enable
The TV’s signal sources can be individually Enabled or Disabled. The available sources in this menu correspond with the
components you have connected to the TV’s connectors.
Note: Please disable all of the TV’s sources that are not to be used. A TV that is switched to a non-connected source
generates nuisance hospital maintenance calls of TV Not Working, when in fact the TV does work, but has been set to an
inactive source
1. From the SETUP menu, press CH▲ or CH▼to highlight Source.
2. Press VOL ◄or VOL ►to select it.
3. Press CH▲ or CH▼ to highlight a desired source.
4. Press VOL ◄or VOL ►to change the source status to either Disabled or Enabled/APO (Auto Power Off).
NOTE: Sources that are grayed out are not installed in the TV. Enabled/APO means the TV will turn off if there is
no video.
5. Press SETUP to return to the previous menu. To exit, press SETUP until the programmingmenus disappear.
Source Name
It is possible to name the sources that you use with your TV.
Choices are: None, Cable, Antenna, Satellite, BD/DVD, VCR,
Game, MP3 Player, IPTV, PC, and Set Top Box
Power on Source
The TV can be preset to power on to a selected source.
1. Enter the Sources menu
2. Press CH▲ or CH▼ highlight Sources.
3. Press VOL ►to select it.
4. Press VOL◄ or VOL► to change to the source that you
want the TV to power on to. Last, TV, Composite Video,
Component, HDMI 1, Android, PC ANALOG, FM Radio,
USB Media.
5. Press SETUP to return to the previous menu. To exit, press
SETUP until the programming menus disappear.
Note: The source must be enabled before it can be chosen as a power on source. The Last entry causes the TV to power
on to the Last source selected.