Peak Atlas ESR60 User manual

Atlas ESR and ESR
+
Capacitance and Equivalent Series Resistance Meter
Model ESR60/ESR70
Designed and manufactured with pride in the UK
User Guide
© Peak Electronic Design Limited 2004/20 2
In the interests of development, information in this guide is subject to change without notice - E&OE
GB60/70-8

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 2
Want to use it now?
We understand that you want to use your Atlas ESR right
now. The unit is ready to go and you should have little need
to refer to this user guide, but please make sure that you do
at least take a look at the notices on page 4!
Contents Page
Introduction......................................................................... 3
Safety Considerations.......................................................... 4
Notes on ESR ...................................................................... 5
Analysing capacitors ........................................................6-8
Typical values of ESR......................................................... 9
Audible Alerts ................................................................... 0
Probe Compensation .........................................................
Care of your Atlas ESR ..................................................... 2
Appendix A – Troubleshooting......................................... 3
Appendix B – Technical Specifications ............................ 4
Appendix C – Warranty Information ................................ 5
Appendix D – Disposal Information ................................. 6

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 3
Introduction
The Atlas ESR is an advanced instrument designed specifically
for the analysis of capacitor equivalent series resistance (in or
out of circuit). In addition it will, where possible, display the
capacitance of the device under test.
Summary Features:
• ESR measurement range 0 to 20Ω (40Ω for ESR70).
• ESR resolution as low as 0.0 Ω.
• Capacitance range µF to 22,000µF.
• Can be used for low-ohms resistance checking too.
• Integrated controlled discharge circuitry reduces the need
for the user to manually discharge capacitors before test.*
• Use in or out of circuit for ESR and low-ohms resistance
measurement.
• The ESR70 features audible alerts for quick user-feedback
of ESR test status.
• Automatic analysis start when component is detected.
• Automatic and manual power-off.
* Note:
The discharge circuitry exists to ensure that a charged capacitor
is less likely to damage the unit. For example, if the capacitor
under test has a potential of a few tens of volts across it, the
charge is removed automatically. It is the user’s responsibility
to ensure that any dangerously charged capacitors are safely
discharged before connection to the unit.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 4
Safety Considerations
WARNING:
This instrument must NE ER be connected to powered
equipment/components.
It is the user’s responsibility to ensure that any dangerously
charged capacitors are safely discharged before connection
to the unit.
To allow the self-protection mechanism to function, always
ensure that the Atlas ESR has completed any analysis
before connecting the test probes to a component.
Failure to comply with these warnings may result in
personal injury, damage to the equipment under test,
damage to the Atlas ESR and invalidation of the
manufacturer's warranty.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 5
Notes on ESR
ESR (Equivalent Series Resistance),
as it’s acronym implies, is the value
of resistance that is effectively in
series with an ideal capacitor.
No capacitor is ideal of course, the detailed equivalent circuit of a typical
capacitor is very complex. For many electrolytic capacitors however, the most
important parameters regarding the capacitor’s performance is the capacitance
and the ESR.
An increase in ESR (due to age, abuse or temperature cycling) can result in
poor capacitor performance. The capacitor becomes less “ideal” and starts to
dissipate more power, an ideal capacitor of course dissipates zero power.
Capacitor manufacturers typically quote the ESR of their products at 00kHz,
which is the same test frequency used by the Atlas ESR.
ESR
C

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 6
Analysing Capacitors
The Peak Atlas ESR is designed to analyse capacitor ESR in or out of circuit.
The two test probes can be connected to the component any way around.
Remember though that in-circuit testing can result in less accurate readings.
Important: To minimise risk of damage to the unit, make sure that the
Atlas ESR has completed any previous analysis before attaching the test
probes to the capacitor. This ensures that the built-in protection circuit is
ready for any charge that may be present on the capacitor.
The Atlas ESR must first be switched
on by briefly pressing the on-test
button.
The unit will start a component analysis
when it detects that the open circuit
probes have been applied to a
component or when on-test button is
re-pressed.
If the capacitor is charged (<50V), the
Atlas ESR will attempt to discharge the
capacitor while showing the progress of
the procedure:
If the Atlas ESR cannot recognise the
component connected to the test probes,
or the capacitance is out of range, the
following message may be displayed:
Monitoring for
Monitoring forMonitoring for
Monitoring for
component
componentcomponent
component...
......
...
Open circuit or
Open circuit orOpen circuit or
Open circuit or
low capacitance.
low capacitance.low capacitance.
low capacitance.
Discharging...
Discharging...Discharging...
Discharging...
Capacitor V= 23V
Capacitor V= 23VCapacitor V= 23V
Capacitor V= 23V
Analysing...
Analysing...Analysing...
Analysing...

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 7
Analysing Capacitors continued
The ESR analysis typically takes under 2 seconds to complete, followed by up
to around 0 seconds for the capacitance measurement (depending on the
characteristics of the capacitor).
As soon as a valid ESR reading has
been obtained, the ESR value is
displayed while the instrument
proceeds to measure the capacitance.
If the presence of external circuitry did
not adversely affect the capacitance
measurement, the capacitor value will
be displayed.
If the capacitance could not be
determined (perhaps it is in-circuit or a
“leaky” capacitor), the display will only
show the value of ESR measured.
It is not necessary to wait for the capacitance measurement to complete if
you’re not interested in the capacitance value. If the probes are removed from
the component under test before the
capacitance measurement has
completed, the display will confirm that
the capacitance has not be measured:
It can be useful to disconnect the probes before the capacitance measurement
has completed if you’re wanting to simply check the ESR of multiple
components in succession.
Measuring C...
Measuring C...Measuring C...
Measuring C...
ES = 0.21
ES = 0.21 ES = 0.21
ES = 0.21
Cap =
Cap = Cap =
Cap = 476.6µF
476.6µF476.6µF
476.6µF
ES = 0.21
ES = 0.21 ES = 0.21
ES = 0.21
In
InIn
In-
--
-Circuit/Leaky
Circuit/LeakyCircuit/Leaky
Circuit/Leaky
ES = 0.21
ES = 0.21ES = 0.21
ES = 0.21
(
((
(C not measured
C not measuredC not measured
C not measured)
))
)
ES = 0.21
ES = 0.21 ES = 0.21
ES = 0.21

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 8
Analysing Capacitors continued
In the event that ESR exceeds the maximum that can be measured, the display
may show:
The ESR measurement range is automatically determined during the analysis.
Typically, the resolution for ESR measurement is as shown in the table below:
ESR alue Automatically
selected test current
Nominal measured
resolution
0.00 Ω – 2.00 Ω 20mA 0.0 Ω
2.0 Ω – 20.0 Ω* 2mA 0. Ω
20.0 Ω – 40.0 Ω* mA 0.2 Ω
Although the measurement resolution is generally determined by the absolute
value of the ESR (as shown in the above table), low capacitance values can
result in a poorer ESR measurement resolution.
* The maximum ESR measurement is limited to 20Ω for the model ESR60
and 40Ω for the model ESR70.
If measuring capacitors connected in parallel, the ESR reading will
effectively be the value of all the ESRs in parallel, not ust the ESR of the
capacitor in contact with the probes.
Cap =
Cap = Cap =
Cap = 476.6µF
476.6µF476.6µF
476.6µF
ES = >20.0
ES = >20.0 ES = >20.0
ES = >20.0
In
InIn
In-
--
-Circuit/Lea
Circuit/LeaCircuit/Lea
Circuit/Leaky
kyky
ky
ES = >20.0
ES = >20.0 ES = >20.0
ES = >20.0
or

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 9
Typical Values of ESR
It is not possible to provide a definitive rule for values of ESR that are
acceptable for all situations.
The expected value of ESR largely depends on the capacitance value and the
voltage rating of the capacitor but also depends on temperature ratings and
other factors. Some capacitors are manufactured to exhibit very low ESR
values, whilst conventional low cost parts are likely to exhibit higher values
but still be acceptable.
As a rough guide only, the following table shows “typical” values of ESR for a
range of different capacitance and voltage ratings.
10 16 25 35 63 160 250
4.7µF >40Ω 35.0Ω 29.0Ω 24.0Ω 9.0Ω 6.0Ω 3.0Ω
10µF 20.0Ω 6.0Ω 4.0Ω .0Ω 9.3Ω 7.7Ω 6.3Ω
22µF 9.0Ω 7.5Ω 6.2Ω 5. Ω 4.2Ω 3.5Ω 2.9Ω
47µF 4.2Ω 3.5Ω 2.9Ω 2.4Ω 2.0Ω .60Ω .40Ω
100µF 2.0Ω .60Ω .40Ω . 0Ω 0.93Ω 0.77Ω 0.63Ω
220µF 0.90Ω 0.75Ω 0.62Ω 0.5 Ω 0.42Ω 0.35Ω 0.29Ω
470µF 0.42Ω 0.35Ω 0.29Ω 0.24Ω 0.20Ω 0. 6Ω 0. 3Ω
1000µF 0.20Ω 0. 6Ω 0. 4Ω 0. Ω 0.09Ω 0.08Ω 0.06Ω
2,200µF 0.09Ω 0.07Ω 0.06Ω 0.05Ω 0.04Ω 0.03Ω 0.03Ω
4,700µF 0.04Ω 0.03Ω 0.03Ω 0.02Ω 0.02Ω 0.02Ω 0.0 Ω
10,000µF 0.02Ω 0.02Ω 0.0 Ω 0.0 Ω 0.0 Ω 0.0 Ω 0.0 Ω
Please note that the above figures are only typical figures for standard grade
electrolytics at room temperature, please verify readings against expected
values for the particular type of capacitor you are testing.
For any particular capacitance and voltage rating,
a lower ESR reading is generally better than a higher ESR reading. For
good quality capacitors it is common for the ESR readings to be much
lower than the figures shown in the above table.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 0
Audible Alerts (Model ESR7 only)
The ESR70 unit can produce audible tones to assist the user.
The various tones are summarised below:
Condition / Operation Sound Type
Start Analysis Short Blip
End Analysis Short Blip
Measured ESR > 40Ω High-Low “Beep Barp”
Measured ESR < 5.0Ω Single Bell “Ping”
Measured ESR < .0Ω Double Bell “Ping-Ping”
The audible alerts can be turned on or off, the current status of which is
shown on the start-up screen (when powering up the unit from off).
You can switch this function on or off by holding down the on-test button
for about 2 seconds when powering up the unit from off. Depending on
whether the sound function was already on or off, one of the following
messages will be displayed to confirm that you have changed the sound
mode:
Sound On
Sound On Sound On
Sound On
Sound Off
Sound Off Sound Off
Sound Off
Atlas ES Plus
Atlas ES PlusAtlas ES Plus
Atlas ES Plus
Enhanced x.x
Enhanced x.x Enhanced x.x
Enhanced x.x
Atlas ES Plus
Atlas ES PlusAtlas ES Plus
Atlas ES Plus
Enhanced x.x
Enhanced x.x Enhanced x.x
Enhanced x.x
Audible Alerts Enabled
Audible Alerts Disabled

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page
Probe Compensation
To ensure good repeatable readings, particularly for low values of ESR, it may
be necessary to occasionally perform a simple Probe Compensation procedure.
This procedure is easiest to perform with the gold plated croc clips fitted.
. Ensure the unit is switched off.
2. Press and hold down the on-
test button for about 5
seconds until the following
message is displayed*:
3. The unit will then ask you to
short the probes together (by
interlocking the jaws of each
croc clip). Then press the on-
test button.
4. After a short delay the display
will confirm that the
procedure is complete and
then switch off.
If the following message is displayed
then the probes may not have been
correctly shorted during the above
proecedure. This message may also be
displayed if any of the probe connections are faulty.
It is useful to test the integrity of the probe compensation by measuring a fixed
resistor of Ω and 0Ω to verify the correct ESR reading respectively.
* NOTE: For the ESR70, the sound on/off mode will be entered while
holding the button down, keep the button held down and the unit will
proceed to the probe compensation mode.
OK
OKOK
OK
Probe
Probe Probe
Probe
Compensation
Compensation Compensation
Compensation
Short probes
Short probes Short probes
Short probes
and press TEST.
and press TEST.and press TEST.
and press TEST.
Compensation
CompensationCompensation
Compensation
Fail. Try again.
Fail. Try again.Fail. Try again.
Fail. Try again.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 2
Care of your Atlas ESR
The Peak Atlas ESR should provide many years
of service if used in accordance with this user
guide. Care should be taken not to expose your unit
to excessive heat, shock or moisture. Additionally, the battery
should be replaced at least every 2 months to reduce the risk of leak
damage.
If a low battery warning message
appears, replacement of the battery is
essential.
Immediate replacement of the battery is EXTREMELY IMPORTANT as the
built-in protection mechanism may not function correctly if the battery
condition is poor and therefore render your unit susceptible to damage from
even low energy charged capacitors.
The Atlas ESR will not continue to operate if a low battery condition is
encountered.
New batteries can be purchased from many retailers and directly from Peak
Electronic Design Ltd or an authorised agent.
Battery types: Suitable battery types include 23A, V23A, GP23A, MN2 or a
good quality 2V alkaline equivalent as used in many test instruments and
automotive remote key fobs.
Battery access: To replace the battery, unscrew the three screws to remove the
rear panel. Remove the old battery and insert a new one, taking care to observe
the correct polarity. Carefully replace the rear panel, do not over-tighten the
screws.
Peak Safe Battery Disposal Scheme: Please return your old analyser battery to
Peak Electronic Design Ltd for safe and environmentally responsible disposal.
**
** **
** Warning **
Warning ** Warning **
Warning **
Low Battery
Low Battery Low Battery
Low Battery

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 3
Appendix A - Troubleshooting
Problem Cause / Possible Solution
ESR value when probes
are shorted is not close
to 0Ω
Perform a probe compensation.
Seems to be stuck
“Measuring
capacitance”
It is possible that one (or more) probe
connections has become broken. Check all
connections at both ends of the test leads.
Display shows
emoving trace
charge
This message is displayed if the Atlas ESR has
detected that the attached capacitor may be
exhibiting “Soakage” or “Dielectric
Absorption”, this is quite normal. The
instrument then ensures that the capacitor is
very well discharged and helps to prevent
voltage developing across the capacitor after
the normal discharge procedure has completed.
Display shows
Auto discharge
taking too long!
The unit attempts to remove charge from the
capacitor using a controlled discharge
procedure. If this takes longer than 60 seconds
then the discharge process will be aborted. It is
recommend that you safely discharge the
capacitor manually and try analysis again.
Display shows
Warning! V=132V
Safely discharge
If the voltage across the capacitor is greater
than 50V then the Atlas ESR will not attempt
to discharge the capacitor, please safely
discharge the capacitor manually.
Display shows
Self Test Fail
Code 2
It is possible that a hardware failure has
occurred, please contact Peak Electronic
Design Limited for assistance.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 4
Appendix B - Technical Specifications
All values are at 25°C unless otherwise specified.
Parameter Min Typ Max Note
Peak test current into S/C ±20mA ±22mA
Peak test voltage, full scale ESR ±40mV ±44mV
Peak test voltage across O/C ±2.5V ±3.0V
Capacitance measurement range µF 22,000µF
Capacitance accuracy ±4% ±0.2µF
ESR measurement range 0Ω 20Ω / 40Ω 2
ESR resolution for ESR < 2Ω 0.0 Ω 0.02Ω
ESR resolution for ESR > 2Ω 0. Ω 0.2Ω
ESR accuracy for ESR < 2Ω ± .5% ±0.02Ω
ESR accuracy for ESR > 2Ω ± .5% ±0.2Ω
Abuse voltage (for C < 0µF) ±275V 3
Abuse voltage (for C > 0µF) ±50V 3
Auto-Discharge voltage limit ±50V
Battery type MN2 /GP23A 2V Alkaline
Battery voltage range 8.5V 2V
Battery voltage warning threshold 8.5V
Inactivity power-down period 30 seconds
Dimensions (excluding test leads) 03 x 70 x 20 mm
Operating temperature range 0°C 40°C
Notes
. Subject to acceptable LCD visibility.
2. Model ESR70 is capable of measuring up to 40Ω.
3. Maximum abuse voltage rated limitation of internal protection electronics.
Probes, leads and unit are not certified for high voltage use.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 5
Appendix C - Warranty Information
Peak Satisfaction Guarantee
If for any reason you are not completely satisfied with the Peak Atlas ESR
within 4 days of purchase you may return the unit to your distributor. You
will receive a refund covering the full purchase price if the unit is returned in
perfect condition.
Peak Warranty
The warranty is valid for 24 months from date of purchase. This warranty
covers the cost of repair or replacement due to defects in materials and/or
manufacturing faults.
The warranty does not cover malfunction or defects caused by:
a) Operation outside the scope of the user guide.
b) Unauthorised access or modification of the unit (except for battery
replacement).
c) Accidental physical damage or abuse.
d) Normal wear and tear.
The customer’s statutory rights are not affected by any of the above.
All claims must be accompanied by a proof of purchase.

ESR60/ESR70 User Guide April 20 2 – Rev 8
Page 6
Appendix D - Disposal Information
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electrical and Electronic Products
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection
and recycling of all waste electrical and electronic equipment. It is no longer
permissible to simply throw away electrical and electronic equipment. Instead,
these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into
national law in slightly different ways. Please follow your national law when
you want to dispose of any electrical or electronic products.
More details can be obtained from your national WEEE recycling agency.
If in doubt, you may send your Peak Product to us for safe and environmentally
responsible disposal.
At Peak Electronic Design Ltd we are committed to continual product development and improvement.
The specifications of our products are therefore subject to change without notice.
© 2004/20 2 Peak Electronic Design Limited - E&OE
Designed and manufactured in the UK
www.peakelec.co.uk Tel. [phone] Fax. [phone]