peerless-AV SC590 Guide

Installation and Assembly: Flat Panel Display Cart
Models: SC590, SC590-S
Max Load Capacity: 300 lb (136.1 kg)
ISSUED: 08-08-12 SHEET #: 009-9074-1
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com
ACC964
(sold separately)

2 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List............................................................................................................................................................................ 3, 4
Assembling Cart.....................................................................................................................................................................5
Installing Vertical Adapters to Flat Panel Display...................................................................................................................9
Mounting Flat Panel Display.................................................................................................................................................11
Tools Needed for Assembly
• phillips screwdriver
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands these
instructions.
• Never exceed the Maximum Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart is not affixed or secured to the floor, and may therefore tip over and/or fall if display and/or cart is shaken or
hit. Always monitor children and do not let children play alone around cart as they could get hurt by a falling display.
Not recommended for use in areas with heavy traffic.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING

3 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Parts List SC590 SC590-S
Description Qty. Part Number Part Number
A
mount bracket 2 201-1156 201-G4156
Bhook plate 2 201-1157 201-G4157
CM10 x .402 ID lock washer 6 540-9424 540-9424
Dbase 1 009-1437 009-G4437
Euniversal plate 1 009-1432 009-G4432
Fadapter bracket 2 201-1513 201-G4513
Gupright 2 580-1180 580-G4180
Htop cover 2 590-1210 590-4210
I1/4-20 x 12mm decorative screw 20 520-2325 520-1325
J1/4-20mm nut 12 530-1050 530-2031
KM10 x 15 mm socket screw 8 520-9262 520-9534
L3/8-16 x 2.5" socket screw 6 520-9550 520-9550
M7/32" allen wrench 1 560-9715 560-9715
N6 mm allen wrench 1 560-9716 560-9716
Q4 mm allen wrench 1 560-9646 560-9646
Rright leg 1 009-1295 009-G4295
Sleft leg 1 009-1296 009-G4296
Twheel caster 2 600-0044 600-0044
Uwheel caster/brake 2 600-0045 600-0045
V
joint connector nut 4 530-1037 530-2037
W
3/8-16 x 1.5" screw bolt 4 520-1329 520-1329
X3/16" allen wrench 1 560-0071 560-0071
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
DE
ABCG
F
H

4 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Parts List continued Parts may appear slightly different than illustrated.
RS
V
UT
M
W
L
KI JNQ
X
M4 x 12mm (6)
(510-1079) M5 x 12mm (4)
(520-1064) M5 x 25mm (4) (520-1122) M6 x 12mm (4) (520-1050)
M6 x 25mm (4)
(520-1211)
M6 x 20mm (4)
(520-9554) M6 x 30mm (4)
(520-1067)
M4 x 25mm (4)
(510-1082)
multi-washer (6)
(580-1036)
M8 x 40mm (4)
(520-1152)
.75" spacer
(540-1059) (4)
M8 x 25mm (4)
(520-1101)
M8 x 15mm (6)
(520-1068)
.5" spacer
(540-1057) (4)
Security Tilt Bracket Fasteners

5 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Insert right leg (R) into base housing (D) as shown in fig. 1.1. Then align holes in right leg with holes in base
housing (D). Fasten base housing to right leg using two 3/8-16 x 1.5" bolts (W) and two joint connectors (V).
NOTE: Left and right legs can be identified by looking at the cart from the front.
Repeat for left side with left leg (S).
1
R
W
V
fig. 1.1fig. 1.1 fig. 1.2
D
R
FRONT OF CART
FRONT OF LEG
2Insert casters (U &T) into holes of support legs (R &S) and hand thread to secure. Attach casters with brake (U)to
the back of left and right support legs (R &S). Attach casters without brake (T)to front of support legs as shown.
NOTE: Lock brakes on casters to avoid sudden movements during installation.
S
U
T
RHAND THREAD
HOLD WHEEL
S

6 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
L
D
G
C
Attach uprights (G) to base (D), as shown below using six 3/8-16 x 2.5" socket screws (L) and M10 x .402ID lock
washers (C). Tighten all screws.
3
Loosely attach six 1/4-20 x 12 mm screws (I) and
1/4-20 nuts (J) to mount bracket (A).
Repeat with second mount bracket (A)
4Slide mount bracket (A) onto upright (G) so that 1/4-
20 nuts (J) slide into slots of upright (G) as shown in
figure 5.1 and detail 1. Slide display mount bracket
to desired position, level, then tighten
1/4-20 x 12 mm screws (I) using 4 mm allen wrench
(Q). Repeat with second mount bracket (A).
NOTE: Make sure that two mount brackets (A)
are level.
5
IA
J
A
G
SLOT
fig. 5.1
I
DETAIL 1
J
G
fig. 3.1

7 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Insert two 1/4-20 x 12 mm screws (I) into mount
bracket (A), leaving 3/16" of exposed thread as
shown in figure 7.1 and detail 2.
H
G
Snap top cover (H) onto upright (G). 7
6
DETAIL 2
3/16"
I
A
Attach one universal plate (E) to two hook plates
(B) using eight M10 x 15 mm socket screws (K).
Tighten screws using 6 mm allen wrench (N).
Attaching Universal Adapter Plate Attach hook plate (B) to mount bracket (A).
A
B
B
8
K
9
E
fig. 7.1

8 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
I
II
2° Backward Tilt 5° Forward TiltNo Tilt
Insert two 1/4-20 x 12 mm screws (I) into holes indicated below for desired display orientation. Tighten all screws
using 4 mm allen wrench (Q).
10

9 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Installing Adapter Brackets
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display.
Place display face side down. If display has knobs on the back, remove them to allow the adapter brackets to be
attached. Place adapter brackets (F) on back of display, align to holes, and center on back of display as shown
below. Attach the adapter brackets to the back of the display using the appropriate combination of screws, multi-
washers, and spacers as shown in figure 11.1 or 11.2.
NOTE: Top and bottom holes on display must always be used.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
NOTE: For flat back displays proceed to step 11-1. For bump-out or recessed back display skip to step 11-2.
NOTE: "X" dimensions should be equal.
FCENTER BRACKETS VERTICALLY
ON BACK OF DISPLAY
X
X
MULTI-WASHER
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not be used,
depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
11
WARNING

10 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (F) into display as
shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through multi-washer, adapter bracket (F) and spacer in that order
into display as shown below. Screw must make at least three full turns into the mounting hole and fit snug into
place. Do not over tighten. If screw cannot make three full turns into the display, select a longer length screw from
the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
11-2
11-1
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
fig 11.2
SCREW
MULTI-WASHER
ADAPTER BRACKET (F)
DISPLAY
SPACER
fig 11.1
SCREW
MULTI-WASHER
ADAPTER BRACKET (F)
DISPLAY

11 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
Mounting and Removing Flat Panel Display
Hook adapter brackets (F) onto universal plate (E),
then slowly swing display in as shown. Turn safety
screws, using security allen wrench (Q), clockwise
at least six times to prevent display from being
removed as shown in detail 3.
NOTE: To lock the display down, tighten safety
screws to wall plate as shown in cross section.
To remove display from mount, loosen safety
screws, swing display away from mount, and lift
display off of mount.
• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel display.
WARNING
12
F
DETAIL 3
SAFETY
SCREWS
E
FE
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerlessmounts.com
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION

12 of 12 ISSUED: 08-08-12 SHEET #: 009-9074-1
© 2012 Peerless Industries, Inc.
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of five years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
This warranty gives specific legal rights, and you may also have other rights which vary from state to state.
LIMITED FIVE-YEAR WARRANTY
www.peerless-av.com