peerless-AV DS-S555-4X3 User manual

12015-06-24 #:009-9117-4 (2018-03-08)
ENG
DS-S555-4X3
46" - 55"
(117 - 140 cm)
1200 lb
(544 kg)
MAX

22015-06-24 #:009-9117-4 (2018-03-08)
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
Display center.
ENG
ENG - Do not begin to install product until you have read and understood the instructions and warnings
contained in this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position
equipment. This product must be installed onto at, hard, level surface to prevent tipping. Use with heavier
displays may result in instability causing tip over resulting in death or serious injury. Displays must be removed
before moving cart. Not recommended for use in areas with heavy trafc. This product is intended for indoor use
only. Use of this product outdoors could lead to product failure or personal injury. Screws must be tightly secured.
Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load
Capacity. Be careful not to pinch ngers when operating the mount. Death or serious injury may occur when
children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may
encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child. Relocating
audio and/or video equipment to furniture not specically designed to support audio and/or video equipment may
result in death or serious injury due to the furnishing collapsing or over turning onto a child. For support please
call customer care at 1-800-865-2112.
WARNING

32015-06-24 #:009-9117-4 (2018-03-08)
Tools Needed for Assembly.
ENG
3/8"
(10mm)
3/8"
(10mm)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3

42015-06-24 #:009-9117-4 (2018-03-08)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Part #Description Qty
Apedestal 3 146-T1132
Bcolumn 3 146-T1131
Cextension 3145-T1778
Dcover 3 145-T1809
Eside support bracket 4 145-T1807
Fvertical support bracket 6 145-T1806
Gleft adaptor bracket 12 146-1609
Hright adaptor bracket 12 146-1608
Icomputer cover 1 145-T1930
Jcomputer shelf 1 145-T1931
Kdual cross support 6 146-T1905
Lextension adaptor 3145-T1935
Mcord bracket 6 146-T1321
Nbracket, 4x2 conguration 3145-T1858
Oknob 6 560-1160
PM8 x 16mm socket button screw 140 520-9527
QM8 square nut 56 530-1066
Rcover clip 12 590-0317
SM5 x 10mm type-f, socket pin screw 26 520-1164
T1/4" power bit 1 560-0263
Ubar nut 6 146-1319
V5mm allen wrench 1 560-9640
Wnylon shoulder washer 48 590-2233
XM6 x 12mm socket pin screw 48 520-1050
Y4mm allen wrench 1 560-9646
ZM6 x 35mm screw 12 520-0717
AA rawl bolt #6913 12 5M9-381-H03
D (3)
cover
B (3)
column
F (6)
vertical support
bracket
E (4)
side support
bracket
A (3)
pedestal
C (3)
extension
H (12)
right adaptor
bracket
G (12)
left adaptor
bracket

52015-06-24 #:009-9117-4 (2018-03-08)
I (1)
computer cover
J (1)
computer shelf
N (3)
bracket, 4x2
conguration
K (6)
dual cross
support
Y (1)
4mm allen
wrench
P (140)
M8 x 16mm
Q (56)
M8 square
nut
R (12)
cover clip
S (26)
M5 x 10mm T (1) 1/4" power
bit
V (1)
5mm allen
wrench
W (48)
nylon shoulder
washer
X (48)
M6 x 12mm
L (3)
extension
adaptor
rawl bolt
AA (12)
M6 x 35mm
Z (12)
M (6)
cord
bracket
O (6)
knob bar nut
U (6)

62015-06-24 #:009-9117-4 (2018-03-08)
Z (4)
AB
2-1
Do not fully tighten hardware
P (4)
U (2)
L
TOP VIEW
x3
1
x3
V

72015-06-24 #:009-9117-4 (2018-03-08)
2-2
TIGHTEN
CONNECTING
HARDWARE
x3
C
B
V

82015-06-24 #:009-9117-4 (2018-03-08)
3-1
3-2
P (6)
Q (4)
F
x6
1/8"
(3mm)
1/8"
(3mm)
TIGHTEN
CONNECTING
HARDWARE
DISPLAY HEIGHT
DISPLAY HEIGHT
x2
V
V

92015-06-24 #:009-9117-4 (2018-03-08)
4
x2x2
5
M (2)
O (2)
TOP VIEW
MO
TIGHTEN
CONNECTING
HARDWARE
R (4)
D

10 2015-06-24 #:009-9117-4 (2018-03-08)
6-1
Use metric formula below and diagram to
right to determine hole pattern required for
center vertical support bracket.
All dimensions are metric.
Use the outside mounting holes when…
a x 4 > 4368mm and a x 3 + b < 4318mm
Use the inside mounting holes when…
a x 4 > 4098mm and a x 3 + b < 4064mm
P (12)
Q (8)
N
Q (8)
N
P (12)
BACK
SIDE
1/8"
(3mm)
b
a
BACK OF DISPLAY
x3 V