peerless-AV ACCXT101 Guide

ISSUED: 07-28-11 SHEET #: 120-9117-4 09-26-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Model: ACCXT101
Installation and Assembly: Left and Right Speaker Mount
for Small Pivot and Articulating Mounts
Max Load Capacity: 10 lb (4.5 kg)

2 of 14 ISSUED: 07-28-11 SHEET #: 120-9117-4 09-26-12
NOTE: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• phillips screwdriver
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
WARNING
A
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
Description Qty. Part #
Aspeaker bracket 2 125-P1413
Bmounting tube 2 125-P1254
Cspeaker clamp 2 125-P1414
Dmount clamp 2 125-P1256
EM5 x 16mm self tapping screw 2 520-9515
Fwasher 4 540-9400
Gmount bracket 1 125-P1255
HM5 x 25mm screw 2 520-9543
Parts List D
F
CB
G
HE

3 of 14 ISSUED: 07-28-11 SHEET #: 120-9117-4 09-26-12
Display mount must be removed from display prior
to installing speaker mount. Attach mount bracket
(G) to display mount using M4, M5 or M6 screws
provided with your display mount.
NOTE: M8 screws cannot be used with this
accessory. NOTE: See your display mount
instructions for details.
1
D
G
Attach mounting tubes (B) to the mount bracket
(G) using two mounting clamps (D) two self tapping
screws (E) and two washers (F). NOTE: Do not fully
tighten screws (E) until step 5.
2
Attach two vertical brackets (A) to the speakers.
Be sure to position the vertical brackets in opposite
directions as shown.
3
A
DISPLAY MOUNT
M4, M5, M6 SCREWS
G
F
B
E

4 of 14 ISSUED: 07-28-11 SHEET #: 120-9117-4 09-26-12
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Attach vertical brackets (A) to mounting tubes (B)
with two speaker clamps (C) two screws (H) and
two washers (F). NOTE: Do not fully tighten screws
(H) until step 5.
4Adjust mounting tubes (B) to position speakers as
desired. Tighten all screws to lock in place.
5
SPEAKER
DISPLAY
B
A
C
HF
A

PUBLICADO: 07-28-11 HOJA #: 120-9117-4 09-26-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com
Modelos: ACCXT101
Instalación y montaje: Altavoz de montaje Pivote de la
Pequeña y articulación de Montes
Capacidad Máxima de Soportar Carga:10 lb (4.5 kg)