PEERLESS A100IWBMOUNT Guide

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
1 of 16
Installation and Assembly: Wallmount for CPA100 and
Whiteboard
Model: A100IWBMOUNT
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
Maximum Load Capacity for Screen: 53 lb (24 kg)
Maximum Load Capacity for Projector : 13.5 lb (6 kg)

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
2 of 16
NOTE: Read entire instruction sheet before you start installation and assembly.
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please
callPeerlesscustomercareat1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-
wareandcomponents.
• NeverexceedtheMaximumLoadCapacity. See pageone.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgetoedge"studfinderishighlyrecommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsfirmly,butdonotovertighten.Overtighteningcandamage the items, greatly reducing theirholding
power.
• Carriageboxhasover100lbs(43kg)ofpressure.Becarefulnottopinchfingers.
• Thisproductis intended for indoor use only.Useof this product outdoorscouldleadtoproductfailureandpersonal
injury.
• Thisproductwasdesignedandintendedtobemountedtothe following supporting surfaces checked below with the
hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-
ing surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following wall construction only;
WALLCONSTRUCTION ADDITIONALHARDWARE REQUIRED
xWoodStud None
WoodBeam None
xSolidConcrete None
xCinderBlock None
xMetalStud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick ContactCustomerService
Otherorunsure? ContactCustomer Service
WARNING
Tools Needed for Assembly
•studfinder ("edge to edge" stud finder is recommended)
•phillipsscrewdriver
•drill
•1/4" bit for concrete and cinder block wall
•1/2" bit for metal stud wall
•5/32" bit for metal or wood stud wall
•level

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
3 of 16
Description Qty. Part #
Awall mount assembly 1 055-1841
Bprojector tube 1 055-1839
Cprojector arm 1 055-1830
Dadapter plate 1 055-1828
Ehook bracket 2 055-1840
Fvertical handle 2 055-1834
Ghorizontal handle 1 055-1835
Hprojector adapter plate 1 055-1822
Islide plate 1 055-1821
Jprojector mount 1 PRG-1
K#10-32 x 0.375" phillips screw 18 520-1130
LM6 x 12 mm serrated washer head socket pin screw 8 510-1050
M0.25"ID spacer 4 590-1050
N1/4-20 x 1.0" hex head screw 2 520-1606
O#10-32 x 3/8" serrated washer head socket pin screw 2 520-1151
P0.25" ID nylon washer 4 540-9460
Q#14 x 2.5" wood screw 6 5S1-015-C03
Racorn nut 2 530-1049
Splug 1 590-1303
T#10-32 x 1-3/8" socket pin screw 2 510-1098
Ualligator anchor 6 590-0097
V5/32" (4 mm) security allen wrench 1 560-9646
W#10-32 x 1/4" socket pin screw 1 520-1196
Xflanged bushing 1 590-1271
Yretainer bushing 1 055-1836
Parts List
G
Beforeyoubegin,makesureallpartsshownareincludedwithyourproduct. B
C
A
D
H J
LK
MNOPQ
EF I
CARRIAGE
RST
Partsmayappearslightlydifferentthanillustrated.

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
4 of 16
1
fig. 1.1
Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes.
Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are
level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart
below.
FLOOR
PROJECTOR
SCREEN
A
Parts List Continued
UV
X
BOTTOMOF
SCREEN
WX Y
TOP
MOUNTING
HOLES
Screen Size Dimension X
63" 36"
77'' 42"
CHART

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
5 of 16
Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.
Fasten two #14 x 2.5" wood screws (Q) into top mounting holes leaving a .25" of exposed thread as shown. Hook
wall mount assembly (A) onto #14 x 2.5" wood screws (Q) as shown in fig. 2.1.
Fasten four #14 x 2.5" wood screws (Q) into wall mount assembly (A) as shown in fig. 2.2. Make sure that the wall
mount assembly (A) is level, tighten all six #14 x 2.5" wood screws (Q).
Skip to step 3.
Installation to Wood Stud Wall
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached
hardwareandcomponents.
• Tightenwoodscrewssothatwallplateisfirmlyattached,butdonot overtighten. Overtightening can damage the
screws,greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovidedisforattachmentofmountthroughstandard thickness drywall or plaster into woodstuds.Installers
areresponsibletoprovidehardwarefor other typesofmountingsituations.
WARNING
2
fig. 2.1
fig. 2.2
CARRIAGE
CARRIAGE
.25"
A
Q
Q
A

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
6 of 16
CORRECT
wallplate concrete
plaster/
drywall
Installation to Solid Concrete or Cinder Block
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breakingoutthebackoftheholewhenenteringavoidorcavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-
wareandcomponents.
WARNING
CUTAWAYVIEW
• Tighten screws so that wall mount is firmly attached,
butdonotovertighten.Overtightening candamage
screws,greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
SOLID
CONCRETE
CINDERBLOCK
• Always attach concrete anchors directly to load-
bearingconcrete.
• Neverattachconcreteanchorsto concrete covered
withplaster,drywall,orotherfinishingmaterial.If
mountingtoconcretesurfacescoveredwitha finishing
surfaceisunavoidable,thefinishingsurfacemust be
counterboredasshownbelow.Besureconcrete
anchorsdonotpullawayfromconcretewhentighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING
2concrete
surface
1
3
2
U
Drill holes and insert anchors (U).
Place wall mount assembly (A)over anchors (U) and
secure with screws (Q).
Tighten all fasteners.
A
U
Q
U
CARRIAGE
AQ
fig. 2.3
Use wall mount assembly (A) as a template to mark
mouting holes. Drill six 5/32" (4 mm) dia. holes to a
minimum depth of 2.5" (65 mm). Insert six anchors (U) in
holes flush with wall as shown (right). Fasten two #14 x
2.5" wood screws (Q) into top anchors (U) leaving a .25" of
exposed thread for each screw (Q) as shown. Hook wall
mount assembly (A) onto #14 x 2.5" wood screws (Q) as
shown in fig. 2.3. Fasten four #14 x 2.5" wood screws (Q)
into wall mount assembly (A) as shown. Make sure that the
wall mount assembly (A) is level, tighten all six #14 x 2.5"
woodscrews(Q).
Skip to step 3.
INCORRECT
wallplate
plaster/
drywall
concrete
.25"
Q

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
7 of 16
Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to
drilling 1/2" holes.
Refer to instruction sheet included with Peerless accessory kit ACC 615 for metal studs to install togglers.
Fasten two 1/4-20 x 2-1/2" screws into top mounting holes leaving a .25" of exposed thread on each as shown in
fig. 2.4. Hook wall mount assembly (A) onto 1/4-20 x 2-1/2" screws.
Fasten four 1/4-20 x 2-1/2" screws into wall mount assembly (A) as shown in fig. 2.5. Make sure that the wall mount
assembly (A) is level, tighten all six 1/4-20 x 2-1/2" screws.
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattached
hardwareandcomponents.
WARNING
Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required)
TOGGLER
Afig. 2.4
1/4-20X2-1/2"PHILLIPSSCREWS
2
.25"
fig. 2.5
A
CARRIAGE
CARRIAGE
1/4-20X2-1/2"PHILLIPSSCREWS

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
8 of 16
A
CARRIAGE
K
B
77" SCREEN
CARRIAGE
63" SCREEN
A
K
B
Fasten three #10-32 x 0.375" phillips
screws(K)tocarriageleavingthree
threadsexposed.Attach retainer
bushing(Y)andflangedbushing(X)to
wall mount assembly (A) using two
#10-32 x 0.375" phillips screws (K).
Slide projector tube (B) into top of wall mount
assembly (A) and secure with two #10-32 x
0.375" phillips screws (K) as shown below.
NOTE: Usecorrectset of mounting holes for
the screen size as shown below.
34
D
K
K
D
THREETHREADS
EXPOSED
K
CARRIAGE
fig. 4.1
fig. 4.2
fig. 4.3
Hookadapterplate(D) onto three
#10-32 x 0.375" phillips screws (K)
as shown in fig. 4.2.
Fastenthree #10-32 x 0.375" phillips
screws (K) into adapter plate (D) as
shown in fig. 4.2. Securely tighten all
six #10-32 x 0.375" phillips
screws (K).
4-2
4-1
NOTE:Twist tube
into wall mount
assembly (A).
X
Y
K
A
NOTE:Tube(B)
shouldwallmount
assembly(A)

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
9 of 16
Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D) leaving three threads exposed as shown in
detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top
slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower
slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown
in fig. 5.2. Securely tighten all four #10-32 x 0.375" phillips screws (K).
5
F
D
THREETHREADS
EXPOSED
DETAIL 1
K
D
K
F
fig. 5.1 fig. 5.2
6
63"SCREEN
77"SCREEN
Fastenhorizontalhandle(G)toverticalhandle(F) using four #10-32x0.375"phillips
screws (K) and two acorn nuts (R).Acorn nuts (R) go on below horizontal handle (G).
RG
F
K
K
NOTE: 77"holelocation
shown. 63" will use second
frombottomholeonvertical
handle(F).

ISSUED:08-08-08 SHEET#:055-9094-1
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
10 of 16
Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm
serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3.
7
DETAIL 3
fig. 7.2
E
L
SCREEN
SCREEN
E
fig. 7.1
77"SCREEN
63"SCREEN
DETAIL 2
SCREEN
BRACKET