PEHA Easyclick Plus 452 FU-EP JR o.T User manual

Paul Hochköpper GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Tel.: [phone] • Fax: [phone] • e-mail: [email protected] • Internet: www.peha.de
GB - 1452 FU EP JR o.T. (Rev04_090225) 126291-03
1. General
1.1 Application
A roller shutter, blinds or an awning with end position switch
(230 V / 50 Hz motor) can be actuated with the UP and
DOWN output of the receiver.
The receiver is operated with Easyclick transmitters (ra-
dio signal). Before use, the transmitters must be assigned
to the receiver (max. 32 receivers). Every transmitter can
control an unlimited number of receivers.
Note: Read through the operating instructions carefully
before putting the device into service.
1.2 Warranty conditions
These operating instructions are an integral part of both the
device and our terms of warranty. They must be handed
over to the user. The technical design of the appliance is
subject to change without prior notification. PEHA products
are manufactured and quality-checked with the latest tech-
nology according to applicable national and international
regulations. Nevertheless, if a product should exhibit a de-
fect, PEHA warrants to make remedy as follows (regard-
less of any claims against the dealer to which the end-user
may be entitled as a result of the sales transaction):
In the event of a justified and properly-established claim,
PEHA shall exercise its prerogative to either repair or re-
place the defective device. Further claims or liability for
consequential damage are explicitly excluded. A justifiable
deficiency is one in which the device exhibits a structural,
manufacturing, or material defect that makes it unusable or
substantially impairs its utility at the time it is turned over to
the end-user. The warranty does not apply to natural wear,
unintended usage, incorrect connection, device tampering
or the effects of external influences. The warranty period is
for 24 months from the date of purchase by the end-user
from a dealer and ends not later than 36 months after the
device’s date of manufacture. German law shall be applica-
ble for the settlement of warranty claims.
1.3 Disposal of the device
The device must be disposed of in compliance with the
laws and standards of the country in which it is operated!
1.4 Conformity declaration
PEHA products may be sold and operated in EU countries
as well as in CH, IS and N. PEHA herewith declares that
the receiver (451 FU-EP JR o.T.) is in compliance with the
fundamental requirements and other relevant provisions of
R&TTE Directive 1999/5/EC. The conformity declaration is
available on the Internet at the following address:
www.peha.de/ServiceDownloads.aspx.
2. Safety
CAUTION! Danger of electrical shock!
The housing contains current-carrying com-
ponents. Contact can lead to personal inju-
ry! All work on the mains network and the
device may only be done by an authorised
electrician.
•Disconnectpowersupplyfromthedevicepriortoper-
forming any work on it.
•Securethedeviceagainstbeingpoweredonagain.
•Checkthatthedeviceispoweredoff.
•Closethehousingsecurelybeforeapplyingpower.
The following must be observed:
•Prevailingstatutes,standardsandregulations.
•State-of-the-arttechnologyatthetimeofinstallation.
•Thedevice’soperatinginstructions.
•Operatinginstructionscanonlycitegeneralstipulations.
These are to be viewed in the context of a specific system.
This device is only intended to be used for its stated appli-
cation. Unauthorised conversions, modifications or changes
are not permissible! This device may not be used in con-
junction with other devices whose operation could present a
hazard to persons, animals or property.
3. Technical specifications
Note: The strength of the radio signal between sender and
receiver decreases with increasing distance. The visually
unobstructed range is about 30 m in passageways and
100 m in open rooms. The range can be increased through
the use of an Easyclick repeater.
4. Installation and commissioning
4.1 Safety information
Installation and commissioning may only be done by an
authorised electrician. Mains power (230 V ~/50 Hz) to elec-
trical equipment must be switched off during installation.
Applicable laws and standards of the country in which the
device is operated must be observed!
4.2 Installation information
•Connect only one motor to the receiver!
• The direction of rotation of the motor can be changed
over without transit time! A motor which permits direct
changeover of the direction of rotation is to be used.
• The UP and DOWN outputs of the receiver
are interlocked.
•NEVERinstallEasyclickreceiversinametalenclosure
or in the immediate vicinity of large metal objects.
•Installationclosetofloorlevelorontheflooris
not recommended.
4.3 Installation
This device is intended for installation in a flush-mount
installation box. They are to be equipped with the 1 - 5
multipurpose frame from the PEHA switch range.
•  Install flush-mounted installation box in a suitable position.
•Protect power supply line with an automatic
circuit breaker (F = max. 10 A)!
•Install connection cables.
•Insertthedeviceintotheflush-mountinstallationbox
and screw-fasten it securely in place.
4.4 Commissioning
•Switchonpowersupplyafterinstallation.
•Programthereceiver(seePoint5).
General data
Transmit frequency 868,3 MHz
Power supply 230V~ / 50 Hz
Power line
protection
Circuit breaker rated
for 10 A, maximum
Ambient temperature - 20 to + 40°C
Storage temperature - 40 to + 85°C
Test specifications EN 60669-2-1
Identification CE ; KEMA/KEUR
Protection type IP20
Load types
Inductive 600 VA
Range in buildings
Masonry 20 m, through 3 walls max.
Reinforced concrete 10 m, through 1 wall/ceiling max.
Plasterboard/wood 30 m, through 5 walls max.
Installation and operating instructions
Easyclick JR-receiver Plus
Art.no.: 452 FU-EP JR o.T.
GB
LRN/SET
CLR/MODE
230V~
50Hz
9 mm
452 FU-EP JR o.T.
NN L
L max.600VA
µµ
LRN / SET
button with
LED
Learn mode
and function
programming
CLR / MODE
button with
LED
Delete all trans-
mitters and pa-
rameter setting
Learn mode:
LED = red
Function programming:
LED = green or orange
230V/50Hz~
L
N
F
N N L 
M
5. Programming
For programming, the receivers must be connected to the
mains power supply. The programming is retained even in
a power failure.
5.1 Learn mode (assigning or deleting transmitters)
Notes:
– No transmitter is assigned to the receiver
in its delivered state.
– Several transmitters can be assigned (max. 32
receivers) or deleted in learn mode.
– A transmitter is alternately assigned (LED on) or deleted
(LED off) each time the button is pressed!
– The receiver‘s Function 1 is preset after assigning a
transmitter to the receiver. The function can be changed
for every transmitter (see point 5.3).
– If no action takes place, learn mode will be terminated
after 30 s.
5.2 Deleting all assigned transmitters
5.3 Function programming
Note: If no action takes place, function programming will
be terminated after 30 s.
LRN/SET button press briefly
Idle state (LED off)
CLR/MODE button long activation
All transmitters deleted
Learn mode (LED blinks red) s. Point 5.1
LRN/SET button
long activation
Function programming
(LEDs blinks green rapidly)
Function setting
(LED blinks orange 
number of blinks = function)
Press LRN/SET button
(number = function selection)
Transmitter detection
( Activate transmitter once )
CLR/MODE button
press briefly
Parameter setting
(LED blinks green 
number of blinks = parameter)
Press LRN/SET button
(number = parameter selection)
CLR/MODE
button
press briefly
Idle state
(LED off)
Transmitter detection (e.g. press transmitter button)
Activate transmitter once
LED blinks orange  transmitter detected
Function setting (e.g. function 3)
LRN/SET button 3 x activated
LED blinks 3 x orange function 3
Parameter setting (e.g. parameter 2)
LRN/SET button 2 x activated
LED blinks 2 x green parameter 2
Activate transmitter once
(e.g. press button)
Transmitter assigned
(LED 1 on)
Receiver = Function 1
Transmitter deleted
(LED off)
LRN/SET button
press briefly
Idle state
(LED off)
LRN/SET button
press briefly
Learn mode
(LED blinks red)

Paul Hochköpper GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Tel.: [phone] • Fax: [phone] • e-mail: [email protected] • Internet: www.peha.de
GB - 2452 FU EP JR o.T. (Rev04_090225) 126291-03
6. Operation and functions
6.1 Operating
The receiver is operated with Easyclick transmitters (radio
signal). Before use, the transmitters must be assigned to
the receiver (max. 32 receivers). The receiver‘s Function 1
is preset after assigning a transmitter to the receiver. It can
be changed by function programming. Every transmitter
can control an unlimited number of receivers.
6.2 Easyclick wall transmitters
6.2.1 Function 1 (Two-button operation)
Note: Standard function after assigning a transmitter!
6.2.2 Function 2 (One-button operation)
6.2.3 Function 3 (Button control))
Taste AUF
Taste AB
Taste O
Taste I
Wall transmitter Function
Press button UP or
DOWN briefly
UP, DOWN or STOP (blade
adjustment for blinds)
Press button UP or
DOWN long
Continuous operation
UP / DOWN (parameter)
Parameters
1120 sec running time
210 sec running time
330 sec running time
460 sec running time
55 min running time
610 min running time
760 min running time
Wall transmitter Function
Press button UP 
or DOWN 
Continuous operation
UP / DOWN (parameter)
Parameters
1120 sec running time
210 sec running time
330 sec running time
460 sec running time
55 min running time
610 min running time
760 min running time
6.2.4 Function 4 (Automatic mode)
Already integrated for future applications! Activating au-
tomatic mode opens up options for using the receiver in
combination with a sun sensor (Point 6.2.6) .
6.2.5 Function 5 (Interlock)
The locking of roller shutters / blinds serves f.ex. the secu-
rity during maintenance work. An activation of the lock is
carried out through a wall transmitter or through a window
contact when the terrace door is open.
6.2.6 Function 6 (Sun sensor)
Already integrated for future applications! Switch on auto-
matic mode (see Point 6.2.4).
Notes:
– Please follow the sun sensor’s instructions.
– The „UP“ function during the „OFF“ signal of the sun
sensors is especially recommendable for sunblinds!
6.2.7 Function 7 (Scenes))
With this function, set positions of the roller shutters / blinds
(scenes) can be stored and called up again.
7. Troubleshooting & remedies
7.1 New system or existing system
•Check power supply (electrician only).
•Check connected electrical loads.
•Check the system’s surroundings for changes that could
cause interference (e.g. metal cabinets, furniture or walls
which have been moved).
•If the transmitter/receiver operates at a reduced distance,
the radio signal was encountering interference or it was
operating outside the transmission range.
•Use the receiver at a better location.
•Delete all transmitters and reprogram the receiver.
7.2 Receiver switches by itself
•This may be caused by operation of an external trans-
mitter that was coincidentally assigned to the receiver.
•Delete all transmitters and reprogram the receiver.
7.3 Radio signal range limitations
•Use of the receiver in the vicinity of metal objects or
materials with metal components.
Maintain a distance of at least 10 cm.
•Moist materials.
•Devices which emit high-frequency signals (e.g. audio
and video systems, computers, electronic ballasts in
lightxtures).Maintainadistanceofatleast0.5m.
7.4 Contact
Telephone:................ [phone]
Fax:.......................... [phone]
Internet:.................... www.peha.de/contact.aspx
E-mail:...................... [email protected]
Wall transmitter Function
Press button UP 
or DOWN 
UP or DOWN (blade adjust-
ment for blinds)
Release button UP 
or DOWN STOP
Parameters
1120 sec running time
210 sec running time
330 sec running time
460 sec running time
55 min running time
610 min running time
760 min running time
Wall transmitter Function
Press button DOWN or IAutomatic mode on
Press button UP or OAutomatic mode off
Parameters
1Sun mode
Magnet max. 5mm
PEHA window contact
(450 FU FK)
Learn mode
Assign / delete window contact with its program button.
Function programming (transmitter detection)
Activate the window contact once with the magnet.
Function setting (e.g. function 5)
LRN/SET button 5 x activated
LED blinks 5 x orange function 5
Parameter setting (e.g. parameter 2)
LRN/SET button 2 x activated
LED blinks 2 x green parameter 2
Sun sensor Function
On signal DOWN (1 s blade adjustment for blinds)
Off signal UP
Parameters
110 sec running time
213 sec running time
316 sec running time
420 sec running time
525 sec running time
630 sec running time
740 sec running time
Wall transmitter Function
Press button DOWN or IUP and interlock
Press button UP or OUnlocking
Window contact Function
Opened Interlock
Closed Unlocking
Parameters
1Wall transmitter safety function
2Window contact safety function
Application example: scene
A scene can be adjusted by using a transmitter and an
available control (various receivers with assigned trans-
mitters).
Programming
Assign the transmitter to each receiver, program func-
tion 7 and set parameter.
Store scene (A-D)
•  Set required positions of roller shutters/blinds.
•Press button/I or /O of the transmitter
for longer than 2s.
Select scene (A-D)
Press briefly the button /I or /O of the transmitter.
Wall transmitter Function (parameter)
Press button / Obriey Switch on scene A/C
Press button / O long Store light A/C
Press button / Ibriey Switch on scene B/D
Press button / I long Store light B/D
Parameter
1button / O = scene A, button / I = scene B
2button / O = scene C, button / I = scene D