Pentair Hydromatic S3S Manual

S3S Shown
SUBMERSIBLE
SEWAGE PUMP
Model S3S/SB3S
06/11
Item # E-03-320
Part # 5625-320-1
© 2011 Pe tair Pump Group, I c.
NOTE! To the i staller: Please make sure
you provide this ma ual to the ow er of
the equip me t or to the respo sible party
who mai tai s the system.
Installat on and Serv ce Manual

2
Thank you for purchasing your
Hydromatic®pump. To help
ensure years of trouble-free
op er a tion, please read the
fol low ing manual carefully.
Before Operation:
Read the following in struc tions
care ful ly. Reasonable care and
safe meth ods should be practiced.
Check local codes and
requirements before installation.
Attention:
This manual contains important
information for the safe use of
this product. Read this manual
completely before using this
product and refer to it often for
con tin ued safe product use.
DO NOT THROW AWAY OR
OSE THIS MAN U A . Keep it
in a safe place so that you may
refer to it often.
Unpa king Pump:
Remove pump from carton. When
un pack ing unit, check for
con cealed damage. Claims for
damage must be made at the
receiving end through the delivery
carrier. Dam age cannot be
processed from the factory.
WARNING: Before handling
these pumps and ontrols,
always dis onne t the power
first. Do not smoke or use
sparkable ele tri al devi es or
flames in a septi (gaseous) or
possible septi sump.
Pumps Not Operating or
in Storage:
Pumps with carbon ceramic seals
must have impellers manually
rotated (6 rev o lu tions) after
setting non-op er a tion al for 3
months or longer and prior to
electrical start-up.
Pump:
The S3S/SB3S submersible pumps
are sup plied for 1 and 3 phase and
for 200, 230, 460 or 575 volts.
Pump is sup plied with 15 feet of
power cord. ong er ca ble lengths
can be furnished but must be
specified at time of order. Power
ca ble is 4 wire with the green wire
for ground. Be sure green wire is
connected to a ground lug in the
control panel and the control
panel must be connected to a
ground rod or ground wire from
supply service.
NOTE: All single phase pumps
require properly sized start
apa itor, start relay and run
apa itor in the panel.
Sump Level Control:
Sump level is controlled by
Hydromatic 3900 mercury switch
level controls. The 3900 level
controls is a metal case
mercury switch sealed in a solid
polyurethane float. The float is
held in position by a weight
at tached to the power cord above
the float. The cord supports the
float and is adjusted for height
from the sur face.
Typical duplex systems use three
floats: the lowest float turns the
pumps off, the next higher float
starts the lead pump, and the next
higher float (override) starts the
lag pump. The pumps alternate
on successive cycles.
General
Informat on
Two pumps operate together only
if sump level rises to the third or
over ride float. The override float
also brings on the sec ond pump in
case of failure of the first pump.
Extra floats with ap pro pri ate
con trols can be sup plied for alarm
functions. Triplex sys tems use
four floats. The fourth highest
float brings on the second lag
pump. Three pumps operate
together only if sump level rises to
the fourth float (sec ond override).
This float also brings on the third
pump in case of fail ure of either or
both of the first two pumps.
Alarm Controls:
The alarm float is usually set
above the override level so the
alarm will sig nal only if the
override level is ex ceed ed.
How ev er, some engineers pre fer
to have the alarm float set be low
the override lev el as it is pos si ble
for one pump to fail and the other
pump to operate on the over ride
level with the sump level never
reach ing the alarm level. This is
par tic u lar ly true in cases of low
inflow capacity.
Ele tri al Control Panel:
It is recommended that the
Hydromatic con trol panel be
used with all pumps as proper
start com po nents and pump
protection are fur nished.
NOTE: All single phase pumps
require properly sized start
apa itor, start relay, and run
apa itor in the ontrol panel.
IMPORTANT: If Hydromati
ontrol panel is not used and
the motor fails be ause of
im prop er omponents, the
motor guar an tee is void.

3
IMPORTANT: When inherent
overheating prote tion is not
provided, use with approved
motor ontrol that mat hes
motor input in full load amperes
with overload element(s) sele ted
or adjusted in a ordan e with
ontrol instru tions.
Hydromatic electrical equipment
is installed in a weatherproof
en clo sure. The electrical
equip ment in cludes a main
cir cuit breaker for each pump,
a magnetic start er with over load
pro tec tion for each pump, an
H-O-A switch and run light for
each pump, an electric al ter na tor
and a trans form er to provide
ap pro pri ate control for control
circuit and alarms.
Overload Heaters:
If a Hydromatic control pan el
is not used, on three phase
pumps all three phases must
have overload protection. The
overload should be ambient
compensated class 10. The
heater's full load amps on the
pump must be sized in ac cor dance
with the name plate amps on
the mo tor housing. The amp
draw on these sub mers ible
mo tors is slightly high er than
a cor re spond ing horsepower
surface motor, so heaters must be
sized by the name plate full load
amp rating.
Single phase pumps with
capacitor start circuit must have
the overload protection on the
black pump lead.
NOTE: On single phase pumps
the white, bla k, and red
pump leads must be onne ted
properly for the pump to run.
Installing Pump in Sump:
Before installing pump in sump,
lay it on side and turn impeller
with fingers. Im pel ler may be
slightly stuck due to fac to ry test
water, so it must be broken loose
with small bar or screwdriver in
edge of vanes. The impeller
should turn freely.
Clean all trash and sticks from
sump and connect pump to piping.
A check valve must be in stalled
on each pump. A gate or plug
Pump
Installat on
valve in each pump discharge line
is also rec om mend ed. This valve
should be in stalled on the
discharge side of the check valve
so if nec es sary to service the
check valve, the line pressure can
be cut off. Single pump sys tems
are sometimes in stalled without a
check valve where it is desirable
to self-drain the dis charge line to
pre vent freez ing. This can be done
only with short dis charge lines.
Oth er wise water will re turn to the
sump and cause short cycling of
the pump.
CONTROL CORD POWER CORD
POTTING
RESIN
SPLICES
230 VOLT SINGLE PHASE
HEAT SENSOR
ON STATOR
PROBE TEST
RESISTOR
ELECTRODE
GROUND
SCREW
MOTOR
STATOR
CONNECTORS
YELLOW
BLACK
RED
RED
GREEN
GREEN
BLK
Y
RED
RED
PURPLE
BROWN
Y
B
R
Y
B
R
GRN
GRN
ORN
RED
Y
BLK
CONTROL CORD POWER CORD
POTTING
RESIN
SPLICES
200 or 575 VOLT SINGLE PHASE
HEAT SENSOR
ON STATOR
PROBE TEST
RESISTOR
ELECTRODE
GROUND
SCREW
MOTOR
STATOR
CONNECTORS
T1
T2
T3
RED
GREEN
GREEN
BLK
Y
RED
RED
P1
P2
Y
B
R
Y
B
R
GRN
GRN
ORN
RED
Y
BLK
CONTROL CORD POWER CORD
POTTING
RESIN
SPLICES
230 VOLT THREE PHASE
HEAT SENSOR
ON STATOR
PROBE TEST
RESISTOR
ELECTRODE
GROUND
SCREW
MOTOR STATOR
CONNECTORS
RED
GREEN
GREEN
BLK
Y
RED
RED
P1
P2
Y
B
R
Y
B
R
GRN
GRN
ORN
RED
Y
BLK
T9
T8
T7
T3
T2
T1
T6
T5
T4
CONTROL CORD POWER CORD
POTTING
RESIN
SPLICES
460 VOLT THREE PHASE
HEAT SENSOR
ON STATOR
PROBE TEST
RESISTOR
ELECTRODE
GROUND
SCREW
MOTOR STATOR
CONNECTORS
RED
GREEN
GREEN
BLK
Y
RED
RED
P1
P2
Y
B
R
Y
B
R
GRN
GRN
ORN
RED
Y
BLK
T9
T8 T7
T3
T2
T1 T6 T5
T4

4
Pump
Installat on
NEMA 4 Jun tion Box
(Optional):
If electrical control panel is to
be set re mote from the pump
sump, a NEMA 4 junc tion box
should be used to make pow er
and control con nec tions. The
Hydromatic NEMA 4 junc tion
box is pro vid ed with com pres sion
con nec tors for seal ing all wires.
No sealing com pound is need ed
to make con nec tions waterproof.
Wiring diagrams are pro vid ed
with the pan el for making
con nec tions. An ex tra set of
di a grams is included so that one
set can be used during installation
when mak ing con nec tions. The
size of any additional wiring from
the pump cord to the panel is
based on the distance and pump
current. Double check that all
wiring is properly connected
and tight.
NOTE: On single phase pumps
the white, bla k and red pump
wires must be onne ted
properly to the panel. Only the
proper sequen e will work.
Installing 3900 Mer ury
Swit h Float:
The float cords are sup port ed by a
mount ing bracket that is at tached
to sump wall or cov er or to the
NEMA 4 junc tion box.
Cord snubbers are used to hold
the cord in place. Float level can
be changed at any time by loos en -
ing the snub ber and re ad just ing
cord length.
In either simplex or duplex
system the lower or turn-off float
is set just above the top of volute
so that the vo lute will always be
sub merged dur ing the pumping
cycle. The second or lead/on float
higher is set at about 24 inches
above the lower turn-off con trol.
More distance between turn-on
and turn-off controls can be used,
but sew age may be come septic
and ex ces sive solids may collect
NUMBER OF CONDUCTORS REQUIRED BETWEEN CONTROL PANEL
AND NEMA 4 JUNCTION BOX
System Numbe of Numbe of Numbe of
Type Cont ol Wi es Powe Lines G ound Wi es #8
Simplex 3 3 1
Simplex with Alarm 5 3 1
Duplex 5 6 1
Duplex with Alarm 7 6 1
WIRE SIZE TABLE
FOR REMOTE LOCATION OF CONTROL PANEL; LENGTHS ARE BASED ON A VOLTAGE DROP OF TWO PER CENT
Maximum ength in feet from NEMA 4 junction box to con tro pane . For 3 phase on y and for power ines on y. A contro wires can be = 14–16 or 18 gauge
wire. If power ines are for 460 or 575 vo ts in su a tion of contro wires must be for this vo tage if used in con duit with power ines.
Volts 230 460 575 230 460 575 230 460 575 230 460 575 230 460 575 230 460 575 230 460 575 230 460 575 230 460 575
Wi e Moto
Size HP 333 5 557½ 7½ 7½ 10 10 10 15 15 15 20 20 20 25 25 25 30 30 30 35 35 35
12 110 450 700 90 370 580
10 180 720 1120 140 550 370 90 360 560 50 220 340
8 270 1100 1650 220 900 1400 175 700 1100 105 420 650 320 500 230 360 180 280
6 400 1600 2500 350 1400 2200 220 900 1400 150 600 930 105 420 650 90 370 570 360 560 320 500 230 360
4 370 1500 2300 230 950 1450 175 700 1100 140 550 850 125 500 800 100 400 620 90 360 560
2 370 1500 230 270 1100 1700 220 900 1400 210 820 1250 200 800 1250 150 600 930
*Specia Junction Box re quired for wire sizes arger than #4.
for the pump to han dle. A frequent
pump ing cycle is rec om mend ed
for best op er a tion.
If an alarm system is used, this
con trol is usually set about 6
inch es above the over ride control.
Some engineers as de scribed
pre vi ous ly prefer to have the
alarm control set be low the
override control.
Making Ele tri al Conne tions:
All electrical wiring must be
in ac cor dance with local code, and
only com pe tent elec tri cians
should make the in stal la tions. A
set of prints is in clud ed for use in
mak ing the in stal la tion. All wires
should be checked for grounds
with an ohm me ter or Megger
af ter the con nec tions are made.
This is im por tant, as one
ground ed wire can cause
con sid er able trouble.
IMPORTANT: If equipment
is not properly wired and
pro te t ed as re om mend ed, the
motor guar an tee is void.

Starting System:
1. Turn H-O-A switch to
Off position, then turn on main
circuit breakers.
2. Open all discharge valves
and al low water to rise in
the sump pump.
3. Turn H-O-A switch to Hand
po si tion on one pump and
notice operation. If pump is
noisy and vi brates, rotation is
wrong. To change rotation
(3 phase), in ter change any two
line leads to motor. DO
NOT INTER CHANGE MAIN
INCOMING INES. If duplex
system, check second pump in
the same manner.
4. Now set both H-O-A switches
to Auto position and allow
water to rise in sump until one
pump starts. Allow pump to
operate until level drops to
turn-off point.
5. Allow sump level to rise to
start oth er pump. Notice run
lights on panel; pumps should
alternate on each suc ces sive
cycle of op er a tion.
6. Turn both H-O-A switch es
to Off po si tion and allow
sump to fill to the over ride
control level.
7. Turn both switches to Auto
po si tion and both pumps
should start and op er ate
to geth er until level drops to
turn-off point.
8. Repeat this operation cycle
sev er al times before leav ing
the job.
9. Check voltage when pumps are
op er at ing and check the amp
draw of each pump. On 3
phase pumps, check amps on
each wire as sometimes a high
Pump
Operat ons
leg will exist. One leg can be
some what high er (5 to 10%)
without caus ing trou ble. For
excessive voltage on one leg,
the power com pa ny should
be consulted.
As the motors are oil filled, no
lu bri ca tion or other main te nance
is required. The pump should be
lifted once every two years and
the oil drained from the motor
chamber to check for water.
Generally these pumps give very
re li able service and can be
expected to op er ate for years
on normal sewage pump ing
without failure.
Lightning:
In some areas where con sid er able
light ning occurs, it is
recommended that a light ning
arrestor be installed at the
con trol panel.
Complete data on lightning
arrestors and their cost is
avail able from the factory.
ight ning ar res tors are good
in sur ance against damage to
an ex pen sive motor.
Servi ing Instru tions:
IMPORTANT: Read all
in stru tions be fore repla ing
any parts.
WARNING: Before han dling
these pumps and ontrols,
always dis on ne t the
power first.
Do not smoke or use sparkable
ele tri al devi es or flames in a
sep ti (gas eous) or possible
septi sump.
Field Servi e on Motor:
All submersible motors can be
ser viced (out of warranty) in the
field by any reliable motor
service shop. Any pump (in
warranty) must be re turned to the
factory for ser vice or repaired
in an au tho rized Hydromatic
ser vice center. Charges will not be
al lowed if (in war ran ty) pump
is not taken to a mo tor repair shop
that is not an authorized
Hydromatic service cen ter.
When field service is per formed
on a pump, these in struc tions
should be care ful ly followed.
Repla ing Stator:
If motor winding is burned or
shorted, it can be rewound or
replaced with new fac to ry wound
stator. Refer to sec tion al draw ing
of pump and mo tor and use the
fol low ing steps to re move and
replace sta tor.
1. If stator only is damaged, it
may not be necessary to
completely dis mantle pump as
stator and hous ing can be
lift ed from pump without
dis turb ing seals or bear ings.
2. Drain all oil from upper
housing. If oil is clean and
no water is present, seals
can be considered satisfactory
to reuse.
3. After chamber is drained,
remove hold-down bolts and
lift off. Use care in lifting.
4. Set assembly on bench and
re move cord cap assembly.
When this is lift ed off,
con nec tion wires to motor will
be exposed. These wires will
prob a bly be burned, but each
wire is tagged with a metal
Pump
Ma ntenance
5

6
Pump
Ma ntenance
marker giv ing wire num ber.
Cut the wires.
5. If the leads to the cord cap
as sem bly are burned, the
assembly must be re placed.
6. After stator retaining ring is
re moved, turn hous ing upright
and bump on hard wood
blocks. This should jar the
stator loose and al low it to
drop out.
7. Thoroughly clean hous ing
before re plac ing new stator.
Replace sta tor and make all
wire con nec tions to cord cap
assembly before re plac ing
hous ing on pump. This is
im por tant as leads must be
tucked be hind the wind ings
by us ing hands up through
ro tor core.
IMPORTANT: Use only
ompression type insulated
on ne tors on the wires. Do not
tape leads as oil will de te ri o rate
the tape and ause dam age to
stator and bear ings.
8. Check top bearing. If clean and
does not turn rough, bearings
can be re used and it is not
necessary to com plete ly
dismantle pump to change
bearings. If bearings are
dam aged with dirt or heat,
they must be re placed. See
ad di tion al instructions on
re plac ing seals and bearings.
Re mem ber to reinstall the
upper bear ing load spring.
9. Replace stator hous ing onto
seal cham ber and bolt in place.
Be sure O-ring seal has been
re placed. If O-ring is nicked
or cut, re place with new ring.
This ap plies to all O-rings used
in as sem bly.
10.After all leads are reconnected,
make a high voltage ground
test on each wire. The only
wire that should show ground
is the green power lead.
11.Refill motor chamber with oil.
Use only high grade trans form er
oil or reg u lar Hydromatic
spe cial sub mers ible oil. Fill
cham ber until oil cov ers top
of wind ings. eave air space
in top for ex pan sion. Use
Permatex on plug threads.
Repla ing Seals and Bearings
1. Drain all oil from motor
chamber as described.
2. Remove bolts that hold motor
hous ing to pump housing.
Re move screws hold ing seal
plate to motor housing.
3. ift rotating assembly (rotor,
shaft and impeller) from pump
case and place hor i zon tal ly on
bench. With hard wood block,
tap end of im pel ler to loosen
from shaft.
4. Shaft sleeves are not used.
5. Remove lower seal spring and
pry out seal with screwdriver.
6. Use bearing puller to remove
bear ings. Replace with new
bear ings. Press only on inner
face of bearing when
replacing. Pressing on outer
face can damage the bear ing.
Bear ings are standard size
that can be ob tained from
any bearing supply house
or can be ob tained from
Hydromatic fac to ry.
7. IMPORTANT: Do not use
any of the old seal parts.
Replace with all new seals.
8. Thoroughly clean all castings
be fore replacing seals. One
grain of dirt be tween the seal
faces can cause fail ure.
Examine all O-rings for nicks
before reusing.
9. Use ocktite on sock et head
lock ing screw in end of shaft.
10.Before refilling cham ber with
oil, air test as de scribed above.
11.Refill chamber with oil as
de scribed above.
12.Always check all leads with
high volt age or with Megger
for grounds before operating
the pump.
Below is a list of common
prob lems and the probable
causes:
Pump will not start
1. No power to the mo tor.
Check for blown fuse or
tripped circuit.
2. Hand-Off-Auto switch may be
in the Off po si tion.
3. Control circuit trans form er
fuse may be blown.
4. Overload relay on start er may
be tripped. Push to reset.
Pump will not start and
over load heaters trip
1. Turn off power and check
motor leads with Megger or
ohmmeter for pos si ble ground.
2. Check resistance of motor
wind ings. All 3 phases
should show close to the
same read ing.
3. If no grounds exist and the
motor wind ings check OK,
remove pump from sump
and check for clogged or
blocked impeller.
Pump
Troubleshoot ng

Pump operates with se le tor
swit h in Hand position but will
not operate in Auto position
1. This indicates trouble in the
float lev el control or the
alternator re lay.
2. To check for defective float
con trol, put selector switch in
Auto po si tion and turn off
main power. Put a jump er wire
on terminal strip. Turn on
power and if pump starts,
trouble is in float con trol.
Replace control.
Pump runs but will not shut off
1. Pump may be air locked. Turn
pump off and let set for
several min utes, then restart.
2. ower float control may be
hung-up in the closed po si tion.
Check in sump to be sure
control is free.
3. Selector switch may be in the
Hand position.
Pump does not deliver prop er
apa ity
1. Discharge gate valve may
be par tial ly closed or
par tial ly clogged.
2. Check valve may be partially
clogged. Raise level up and
down to clear.
3. Pump may be running in
wrong di rec tion. ow speed
pumps can op er ate in re verse
direction with out much noise
or vibration.
4. Discharge head may be
too high. Check total
head with gauge when pump is
op er at ing. Total head is
dis charge gauge pressure
con vert ed to feet plus vertical
height from water level in
sump to center line of pres sure
gauge installed in dis charge
line. Gauge should be in stalled
on pump side of all valves.
Multiply gauge pres sure in
pounds by 2.31 to get head
in feet.
5. If pump has been in service for
some time and capacity falls
off, re move pump and check
for wear or clogged impeller.
7

8
1 00 89-002-1 Eyebolt 2
2 19100A033 Capscrew 2
4 04 80-001-1 Drive Screw 4
14981-001-1 Pipe Plug 1
6 01032-003-1 Nut – Hex 3/8-16 SST 2
7 00064-003-1 Load Spring 1
8 0006 -021-1 Upper Bearing R 1
9 0006 -027-1 Lower Bearing R 1
10 00300-000-1 Shaft Seal S 1
00696-000-1 Shaft Seal (Carbide) Opt C 1
11 19103A04 Capscrew 4
12 01130-003-1 Machine Screw (Flat Head) 4
13 09947-000-2 Volute Case for S3S (shown) 1
09947-100-2 Volute Case for SB3S 1
14 10012-000-1 Impeller Washer 1
1 19100A003 Impeller Capscrew 1
16 10102-001-1 Key 1
17 099 2-002-2 Seal Plate 1
18 001 0-021-1 O-Ring SC 1
19 00 17-007-1 Capscrew 4
20 0099 -008-1 Lockwasher 4
21 00299-002-1 Stator Retaining Ring 1
22 09927-008-2 Impeller (1-1/2 HP) 1
09927-009-2 Impeller (2 HP) 1
09927-016-2 Impeller (3 HP) 1
23 00740-019- Rotor w/Shaft (1-1/2 & 2 HP 1ø) 1
7773-018- Rotor w/Shaft (2 HP, 1-1/2 HP 3ø) 1
23 01329-024- Rotor w/Shaft (3 HP 1ø) 1
01329-024- Rotor w/Shaft (3 HP 3ø) 1
24 24407C21 Stator (1-1/2 & 2 HP 1ø 230V) R 1
24407C217 Stator (1-1/2 & 2 HP 3ø 230/460V) R 1
24407C216 Stator (1-1/2 & 2 HP 3ø 200V) R 1
24407C218 Stator (1-1/2 & 2 HP 3ø 7 V) R 1
24407C200 Stator (3 HP 1ø 230V) R 1
24407C202 Stator (3 HP 3ø 230/460V) R 1
24407C201 Stator (3 HP 3ø 200V) R 1
24407C203 Stator (3 HP 3ø 7 V) R 1
2 00736-001-1 Spacer Ring (1-1/2 & 2 HP 1ø) 1
Ref. Part Part
No. No. Description Qty.
00736-000-1 Spacer Ring (1-1/2 & 2 HP 3ø) 1
26 12672A001 Wire Connector (all 1ø & 200/ 7 V 3ø) 3
00282-001-1 Wire Connector (230/460V 3ø) 6
27 0 4 4-001-1 Roll Pin 1
28 13391-000-2 Motor Housing 1
29 00834-01 -1 O-Ring SC 1
30 06461-002- Cord Cap Assy. 1 ' Single 12/4 1
(1-1/2 & 2 HP)
06461-040- Cord Cap Assy. 3 ' Single 12/4 1
(1-1/2 & 2 HP)
06461-023- Cord Cap Assy. 1 ' Single 10/4 (3 HP) 1
06461-041- Cord Cap Assy. 3 ' Single 10/4 (3 HP) 1
1700-060-7 Seal Kit R
1700-360-7 Carbide Seal Kit
* Rebuild Kit
31 Paraffinic Oil
32 003 6-000-2 Discharge Flange 1
33 1910 A044 Screw Cap 2
34 010 4-000-1 Gasket 1
ORDERING REP ACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur nished
as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1)
pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller),
(6) quan ti ty required, and (7) shipping instructions.
Ref. Part Part
No. No. Description Qty.
Ref. Part Part
No. No. Description Qty.
S3S/SB3S
Parts L st
Notes: S — Parts in Seal Kit C — Parts in Carbide Seal Kit I — Parts in Impeller Kit R — Parts in Rebuild Kit *Consult Factory
— Fill Oil to above the Motor Windings

9
30
29
28
26
25
19
21
31
18
17
22 15 16
4
5
7
8
27
9
10
12
13
14
3
2
1
11
24
23
6 (Not Shown)
20
S3S/SB3S

– Your Authorized Local Distributor –
www.hydromatic.com
STANDARD LIMITED WARRANTY
HYDROMATIC®warrants its products against defects in material and workmanship for a period of 12 months
from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first -
provided that such products are used compliance with the requirements of the Hydromatic catalog and
technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free
non-corrosive liquids.
During the warranty period and subject to the conditions set forth, Hydromatic, at its discretion, will repair or
replace to the original user, the parts which prove defective in materials and workmanship. Hydromatic
reserves the right to change or improve its products or any portions thereof without being obligated to provide
such a change or improvement for prior sold and/or shipped units.
Start-up reports and electrical schematics may be required to support warranty claims. Warranty is
effective only if Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be
hooked up, functional and monitored or this warranty will be void. Hydromatic will only cover the lower seal
and labor thereof for all dual seal pumps. Under no circumstance will Hydromatic be responsible for the cost
of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from
the factory or an authorized Hydromatic service facility.
This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly
install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting
from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such
service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good
trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other
than for what it is designed and manufactured; (g) to any unit which has been repaired or altered by anyone
other than Hydromaticor an authorized Hydromatic service provider; (h) to any unit which has been repaired
using non factory specified/OEM parts.
Warranty Exclusions: HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.
Liability Limitation: IN NO EVENT SHALL HYDROMATIC BE LIABLE OR RESPONSIBLE FOR
CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER
TO ANY HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE
MAY RESULT FROM IMPROPER INSTALLATION. HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING
LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. HYDROMATIC RECOMMENDS
INSTALLATION BY PROFESSIONALS.
Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of
incidental or consequential damages and therefore such limitations may not apply to you. No warranties
or representations at any time made by any representatives of Hydromatic shall vary or expand the
provision hereof.
USA
740 East 9th Street, Ashland, Ohio 44805
Tel: [phone] Fax: [phone]
CANADA
269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5
Tel: [phone] Fax: [phone]
Warranty Rev 02/09

START-UP REPORT
cut along dotted line
Distributor:__________________________________________________ Order No.: _________________________
Installing Contractor: _________________________________________ Phone: ____________________________
Sales Contact: ______________________________________________ Phone: ____________________________
Customer: ______________________________________________________________________________________
Location: _______________________________________________________________________________________
1. SYSTEM INFORMATION
Size of Wet Well:_______________________________________Manufacturer: _____________________________
Discharge from Bottom of Basin: ________________________Discharge Location:________________________
Inlet from Bottom of Basin: _____________________________Inlet Location: _____________________________
Type of Check Valves: __________________________________Type of Piping: ____________________________
Does System Have Suction Gauges? ❑Yes ❑No Suction Pressure Reading: __________________
Does System Have Discharge Gauges? ❑Yes ❑No Discharge Pressure Reading:________________
Liquid Being Pumped:_______________________Temperature (F°): __________ Pct. of Solid (%):___________
Is a Sketch or Photograph of System Available? ❑Yes ❑No If So, Please Attach.
Any Additional Comments on System:______________________________________________________________
_______________________________________________________________________________________________
2. ELECTRICAL INFORMATION
Control Panel Part Number: _____________________________Panel Rated Amps: ________________________
Manufacturer: _________________________________________Voltage: _______________ Phase: ____________
Heater Size:___________________________________________Location of Panel to Wet Well: _______________
Incoming Line Voltage: _________________________________Actual? ___________________________________
Voltage to Pumps: _____________________________________Actual? ___________________________________
Type of Junction Box: __________________________________Manufacturer of Junction Box: ______________
Are Floats Installed in Wet Well? ❑Yes ❑No Are Floats Set to Engineer’s Specs? ❑Yes ❑No
Are Floats Wired for Proper Sequencing? ❑Yes ❑No Are Heat Sensors Hooked Up? ❑Yes ❑No
Is the Seal Leak Detection Hooked Up? ❑Yes ❑No
Any Additional Comments on Electrical: ____________________________________________________________
_______________________________________________________________________________________________
3. PUMP INFORMATION
Type of Pump:_________________________________________Serial Number of Pump: ____________________
Voltage of Pump: ________________ Phase: _______________RPM: _________________ Amps: ____________
Impeller Size:____________________ C.O.S. TDH: __________GPM: _________________
Voltage Supplied from Panel:____________________________Actual?___________________________________
Actual Amperage (All Phases): Phase 1 Amps: ________ Phase 2 Amps: ________ Phase 3 Amps: ________
Define the Rotation of the Pump: ❑Clockwise ❑Counterclockwise
Method Used to Check Rotation: ❑Viewed from the Top ❑Viewed from the Bottom
Any Additional Comments on Pumps: ______________________________________________________________
_______________________________________________________________________________________________
4. ACKNOWLEDGE
Acknowledge that all information is accurate and proper procedures have been followed.
Customer: ___________________________________________________________________ Date: _____________
Start-up Technician:___________________________________________________________ Date: _____________
Send to Warranty Manager, 1101 Myers Parkway, Ashland, OH 44805
or Fax to 419-207-3344
or email to [email protected]
or submit online at http://forms.pentairliterature.com/startupform/startupform.asp?type=h