Pepperl+Fuchs IDM-Z2-264-M-2D-J2-BT-N-N0 User manual

IDM-Z2-264-M-2D-J2-BT-N-N0
IDM-Z2-164-M-1D-J2-BT-P-N0
Bluetooth®handheld
scanner for use in explosion-
hazardous areas Zone 2/22
Manual

With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical Industry, published
by the Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elek-
troindustrie (ZVEI) e.V.) in its most recent version as well as the supplementary clause:
"Expanded reservation of proprietorship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [e-mail]
North American Headquarters
Pepperl+Fuchs Inc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [email protected]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [email protected]l-fuchs.com
https://www.pepperl-fuchs.com

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Contents
2022-12
3
1 History of the Manual ................................................................................................ 4
2 Safety .......................................................................................................................... 5
2.1 Introduction.................................................................................................... 5
2.1.1 Content of this Document ................................................................................................... 5
2.1.2 Manufacturer ...................................................................................................................... 5
2.1.3 Target Group, Personnel ..................................................................................................... 5
2.1.4 Symbols Used ....................................................................................................................6
3 Technical Specifications ........................................................................................... 7
3.1 Explosion Protection ..................................................................................... 7
3.2 Technical Data................................................................................................ 8
3.3 Use .................................................................................................................. 8
4 System Structure ....................................................................................................... 9
4.1 Overview......................................................................................................... 9
4.2 System Structure 1 ........................................................................................ 9
4.3 System Structure 2 ...................................................................................... 11
4.4 System Structure 3 ...................................................................................... 13
4.5 System Structure 4 ...................................................................................... 14
5 Commissioning........................................................................................................ 15
5.1 Preparing Bluetooth®Handheld Scanners............................................... 15
5.2 Pin allocation of supply cable SK-IDM-Z2-J2-5M-S-N RS-232 interface. 22
5.3 Pin allocation of supply cable SK-IDM-Z2-J2-1M-U-N USB interface ..... 24
6 Accessories.............................................................................................................. 26

2022-12
4
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
History of the Manual
1 History of the Manual
Version Comments
12/2022 First edition for scanner generation x64

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Safety
2022-12
5
2Safety
2.1 Introduction
2.1.1 Content of this Document
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
In addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•Instruction manual
•Functional safety manual
•Other documents
2.1.2 Manufacturer
2.1.3 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product.The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the Internet at
www.pepperl-fuchs.com.
Note
For specific device information such as the year of construction, scan the QR code
on the device. As an alternative, enter the serial number in the serial number search
at www.pepperl-fuchs.com.
Pepperl+Fuchs Group
Lilienthalstraße 200, 68307 Mannheim, Germany
Internet: www.pepperl-fuchs.com

2022-12
6
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Safety
2.1.4 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. It is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbols
Action
1. This symbol indicates a paragraph with instructions.You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Technical Specifications
2022-12
7
3 Technical Specifications
3.1 Explosion Protection
1-D-/2-D-model
II 3G Ex ic IIB T4 Gc
II 3D Ex ic IIIC T135°C Dc
Te s t c e r t i f i c a t e
IBExU19ATEXB016X
IECEx IBE 19.0026X
Manufacturer
Pepperl+Fuchs SE
Lilienthalstraße 200
68307 Mannheim
Germany
[e-mail]
www.pepperl-fuchs.com

2022-12
8
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Technical Specifications
3.2 Technical Data
3.3 Use
The handheld scanner is a piece of handheld device.
It enables portable recording and direct data transfer of barcodes and 2-D codes in explosion-
hazardous areas.The device is modified for use in explosion-hazardous areas of Zone 2 and
Zone 22.
IDM-Z2-164-M-1D-J2-BT-P-
N0
IDM-Z2-264-M-2D-J2-BT-N-
N0
Description Linear imager 2-D imager
Barcode One-dimensional 1-D (Bar-
code and stacked code incl.
PDF417)
One-dimensional 1-D & 2-D
(Barcode and stacked code
incl. PDF417)
Barcode types Code 39, Code 39 Trioptic, Code 32, Code 93, Code 11, Cod-
abar, Code 128, GS1-128 / EAN 128, UPC / EAN / JAN (with
addition), MSI/Plessey, UK/Plessey, IATA, Interleaved 2 of 5,
Standard and Industrial 2 of 5, Matrix 2 of 5, Telepen, GS1
DataBar, Australian Post, China Post, German Post, US
Planet, US Postnet, British Post, Intelligent Mail, Japan Post,
Korean Post, Dutch KIX Post
Stacked codes PDF417, MicroPDF417, Code
49, Code 16K, Composite,
Codablock F
2-D code types -Data Matrix, QR code,
MicroQR-Code, Aztec, Maxi-
Code
Light source LED, visible red light (630 nm)
Scan frequency 500 Hz 60 Hz
Reading distance 50 mm ... 800 mm 30 mm ... 380 mm
Code resolution Approx. ≥0.076 mm Approx. ≥0.13 mm
Immunity to extraneous light 100?000 lx
Electrical data
Current consumption 330 mA (Standby 80/130 mA; Peak 500 mA)
Battery Lithium ion battery 3.6 V; 1500 mAh
Battery power Up to 60?000 scans at full battery charge
Feedback
Visual 2 x LED (operating state/read confirmation)
Acoustic Buzzer (can be switched off)
Ambient conditions
Shock resistance 50 drop tests on concrete from a height of 2 m
Operating temperature -20°C to +50°C
Storage temperature -30°C to +70°C
Relative humidity 95% non-condensing
Mechanical data
Degree of protection IP65
Dimensions [W x H x D] 104 mm x 176 mm x 76 mm
Weight Approx. 220 g, incl. battery

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
2022-12
9
4 System Structure
4.1 Overview
The Bluetooth®handheld scanner and their accessories are presented in the following over-
view. Charging the handheld scanners batteries can take place within the hazardous area
using the Zone 2/22 certified base station and the associated power module. Furthermore, the
barcode scanner can be charged in the non-explosion-hazardous area using a base sta-
tion/charging cradle.
4.2 System Structure 1
Overview of the complete system structure 1: Base station with Bluetooth®handheld bar-
code scanner IDM-Z2-x64-M-* connected via serial communication protocol to the intrinsically
safe supply cable and a host PC in the non-explosion-hazardous area.
Figure 4.1
Optional Accessories:
Bluetooth®Barcode Scanner, serial connection to Host PC (stand-alone)
Item no. Product Name Description Photo
#548395 HOLDER-BRACKET-
AG1-IDMx61-B-N0
Bracket to mount IDMx61-B-J1-BTN0
Base station to AG1 housing
- Material: Stainless steel AISI 304
(1.4301)
- Assembly: Right side of AG1 housing or
Holder bracket
- Includes bracket and installation materi-
als
- Note: Base station and cables not
included!
#70142693 HOLDER-BRACKET-
SK-IDM-Z2-N0
Bracket to wall-mount SK-IDM-Z2-J2-*
barrier
- Material: Stainless steel AISI 304
(1.4301)
- NOTE: Barrier not included!
Note
The supply cable is available for RS-232 and USB, make sure to use the compatible RS-232
supply (SK-IDM-Z2-J2-5M-S-N) - and connection cables (CBL-IDMx60-D-J1-S *).

2022-12
10
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
Description:
The Bluetooth®handheld scanner has been designed with the battery for explosion-hazard-
ous areas. For proper operation in explosion-hazardous areas, a IDM-Z2-x64-B-J2-BT-N0
base station, a supply cable SK-IDM-Z2-J2-5M-S-N and CBL-IDMx60-* connection cable are
required
The Bluetooth®handheld barcode scanner is designed to be used in explosion-hazardous
areas Zone 2/22.The connection in this structure uses the supply cable SK-IDM-Z2-J2-5M-S-
N which is connected to the communication interface and realizes the data and intrinsically
safe power supply. The RS-232 interface of the host PC is located in the non-explosion-hazard-
ous area. Data communication is via the RS-232 interface, while the base station is powered by
the additional power supply. The power is transferred within the supply cable SK-IDM-Z2-J2-
5M-S-N into intrinsically safe power.
Note
This scenario can also be realized with USB protocol. With the USB-interface version, the
maximum total cable length of the supply cable SK-IDM-Z2-J2-1M-U-N is 1 meter. Use the
compatible USB cables CBL-IDMx60-D-J1-U*.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
2022-12
11
4.3 System Structure 2
Overview of the complete system structure 2: Base station with Bluetooth®handheld bar-
code scanner IDM-Z2-x64-M-* connected via serial communication protocol to the supply
cable and a host PC in the non-explosion-hazardous area with optional GR.TJE.13.13.09.B-
S0008 connection box for long communication distances.
Figure 4.2
Optional Accessories:
Note
The Supply cable is available for RS-232 and USB, make sure to use the compatible RS-232
supply (SK-IDM-Z2-J2-5M-S-N) - and connection cables (CBL-IDMx60-D-J1-S *).
Bluetooth®Barcode Scanner, serial connection to Host PC with optional EPE
connection box (stand-alone)
Item no. Product Name Description Photo
#548395 HOLDER-BRACKET-
AG1-IDMx61-B-N0
Bracket to mount IDM-Z2-x64-B-J2-BT-
N0 Base station to AG1 housing
- Material: Stainless steel AISI 304
(1.4301)
- Assembly: Right side of AG1 housing or
Holder bracket
- Includes bracket and installation materi-
als
- Note: Base station and cables not
included!

2022-12
12
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
Description:
The Bluetooth®barcode scanner is designed to be used in explosion-hazardous areas Zone
2/22. For proper operation in explosion-hazardous areas, the permissible RS-232 cordsets
CBL-IDMx60-D-J1-S* must be used. The intrinsically safe power supply and data transfer are
realized via this cable. The connection in this structure uses the supply cable SK-IDM-Z2-J2-
5M-S-N which is connected to the communication interface.
The RS-422 interface of the host PC is located in the non-explosion-hazardous area. Data
communication is via the RS-422 interface, while the handheld barcode reader is powered by
the additional power supply. The power is transferred within the supply cable SK-IDM-Z2-J2-
5M-S-N into intrinsically safe power. To overcome long communication distances up to 200 m,
an optional GR.TJE.13.13.09.B-S0008 connection box can be installed.
#70142693 HOLDER-BRACKET-
SK-IDM-Z2-N0
Bracket to wall-mount SK-IDM-Z2-J2-*
barrier
- Material: Stainless steel AISI 304
(1.4301)
- NOTE: Barrier not included!
#70142118 GR.TJE.13.13.09.B-
S0008
Enclosure material: glass fiber reinforced
polyester (GRP)
Enclosure size (HxWxD): 130 x 130 x 130
mm
Finish: inherent color black
enclosure cover: fully detachable
Gasket: foamed silicone
Explosion protections gas: Ex eb IIC T4
Gb
Explosion protection dust: Ex tb IIIC
T135°C Db
Ambient temperature: -40°C to +60°C
Degree of protection: IP66
Certification: ATEX, IECEx & UK Ex (oth-
ers on request)
Equipped with: 7x MUT2.5, labeled "1-7"
2x MUT2.5-PE, labeled "PE"
1x M20 –top centered
1x M16 (connection barcode reader
cable) –bottom centered
1x Blind plug or Cable gland M16 left side
1x Blind plug or Cable gland M20 right
side
Item no. Product Name Description Photo
Note
It is the customer's responsibility to ensure that the voltage applied at the front arrives at the
rear of the unit.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
2022-12
13
4.4 System Structure 3
Overview of the complete system structure 3: Bluetooth®handheld barcode scanner IDM-
Z2-x64-M-* connected via supply cable SK-IDM-Z2-J2-1M-U-N to the USB interface of the Vis-
uNet FLX system.
Figure 4.3
Required Components:
•VisuNet FLX System configured with adapter ADAPTER-3200-10-304B-M12
•IDM-Z2-x64-B-J2-BT-N0 base station
•Bluetooth®Barcode Scanner
•CBL-IDMx61-B-Jx-U-S07-N0 base station connection cable
•SK-IDM-Z2-J2-1M-U-N Supply Cable (USB)
•HOLDER-BRACKET-XX00-IDMx61-B-N
Description:
The handheld scanner is designed to be used in explosion-hazardous areas. For proper opera-
tion in explosion-hazardous areas, the permissible USB supply cable SK-IDM-Z2-J2-1M-U-N
cordsets must be used. The intrinsically safe power supply and data transfer are realized via
this cable and directly connected to the USB Port of the VisuNet FLX through the M12 cable
gland of the backside of the system housing. The required adapter ADAPTER-3200-10-304B-
M12 provides the housing feedthrough and has a connection socket that fits the scanner con-
nection cable.
With the accessory cable CBL-IDMx61-B-Jx-U-S07-N0 the base station can easily be con-
nected to the connection socket of the adapter.
Zone 2/22 Barcode Scanner, USB connection to VisuNet FLX
Note
Find details regarding the mechanical installation in the VisuNet FLX system manual.

2022-12
14
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
System Structure
4.5 System Structure 4
Overview of the complete system structure 4: Wired 1-D or 2-D handheld scanner IDM-Z2-
x64-M-* connected via base station/charger to the power module and the USB Ex i interface
"3" (Module A or B) of the VisuNet GXP.
Figure 4.4
Required components:
•VisuNet GXP system with interface "3"
•DATL-IDM-DB-S-XX00-N0 connection cable VisuNet GXP interface
•CBL-IDMx61-B-Jx-S-S07-N0 base station connection cable
•Bluetooth®barcode scanner (1-D or 2-D)
•IDM-Z2-x64-B-J2-BT-N0 base station
•HOLDER-BRACKET-XX00-IDMx61-B-N
Description
The Bluetooth®handheld barcode scanner is designed to be used in explosion-hazardous
areas. For proper operation in explosion-hazardous areas, an IDM-Z2-x64-B-J2-BT-N0 base
station, the permissible RS-232 cordsets CBL-IDMx60-D-J1-S* and the DATL-IDM-DB-SXX00-
N0 connection cable must be used. An accessory cable DATL-IDM-DB-S-XX00-N0 is required
for a connection to the VisuNet GXP in the AG-XX00 housing via the interface "3" option.This
provides the housing feedthrough and has a connection socket that fits the scanner connection
cable.The intrinsically safe power supply and data transfer are realized via the CBL-IDMx61-B-
Jx-U-S07-N0 connection cable.
Z2 Bluetooth®Barcode Scanner connection to VisuNet GXP via "S3" interface
Note
The installation of the IDM-Z2-x64-B-J2-BT-N0 base station with either the IDM-Z2-164-M-1D-
J2-BT-P-N0 or IDM-Z2-264-M-2D-J2-BT-N-N0 barcode scanner to the integrated barrier of the
VisuNet GXP requires the optional interface "3". Refer to the VisuNet GXP technical data
(Module A and B) for further information regarding the interfaces.
Warning!
Zone 2/22 VisuNet GXP system installations are only suitable for use in Explosion Group IIB.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
2022-12
15
5 Commissioning
The battery BAT-IDM-Z2-x61-M is required for commissioning the Bluetooth®Zone 2/22 hand-
held barcode scanner.
5.1 Preparing Bluetooth®Handheld Scanners
Preparation of Bluetooth®handheld scanners
1. The battery compartment is on the underside of the Bluetooth®handheld scanner. Loosen the
screw with a suitable tool to remove the cover. After loosening the screw, some force is required
to remove the cover.
Figure 5.1 Removing the battery compartment lid.
2. The battery is required to commission the Bluetooth®handheld scanner. The protective cap
must be removed before inserting the battery into the handheld scanner.
Caution!
Battery!
Only this battery, which is intended for this purpose, may be used!
Note
Charge the new battery pack for 8 hours prior to the first use!
Warning!
Self discharge of the batteries!
When the batteries are inserted in the barcode reader, they tend to discharge more quickly.
This effect can also occur when the barcode reader is not in use and is in stand-by mode. If the
batteries are not inserted in the device, they will discharge more slowly. If the batteries are
inserted in the scanner, i.e. in stand-by mode, it is recommended to charge them regularly.
Danger!
The battery must not be changed or inserted in explosion-hazardous areas. Improper handling
can void the type approval.

2022-12
16
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
Figure 5.2 Removing the protective battery cap.
3. The battery is inserted into the compartment on the handheld scanner. The end of the pull tab
must be seen protruding out of the opening of the handheld scanner. If the battery is inserted
correctly and connected to the contacts, there is an audible and visual signal. The opening
must be completely sealed again. Before commissioning, check whether the screw cap has
been properly sealed.
Figure 5.3 Inserting the battery and closing the protective cap.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
2022-12
17
Using the base station in explosion-hazardous areas - system structure
1
1. Use the connection cable CBL-IDMx* to connect the base station to the cable barrier SK-IDM-
Z2-J2-*. First, install the RJ50 male connector of the connection cable into the RJ50 port of the
base station. The port is on the bottom side of the base station. The connection cable is
properly installed when you can hear an acoustical click. Ensure that the connection cable is
firmly connected. Then proceed and connect the M12 connector of the connection cable with
the female M12 connector of the cable barrier connection cable.This cable is pre-installed and
shipped with the cable barrier.
Figure 5.4 Connecting RJ50 connector of connection cable CBL-IDM* to base station.
Figure 5.5 Male M12 connector of connection cable CBL-IDM*.

2022-12
18
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
Figure 5.6 Female M12 connector of pre-installed base connection cable of the cable barrier SK-
IDM-Z2-J2-*.
Figure 5.7 Connecting the plug coupling to the supply module basic connection line.

IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
2022-12
19
2. The handheld reader is placed in the charger.The underside of the handle is used first to
ensure that the charging contacts are properly connected. The LED light on the scanner head
indicates successful charging.
Figure 5.8 Inserting the scanner into the base station.

2022-12
20
IDM-Z2-264-M-2D-J2-BT-N-N0, IDM-Z2-164-M-1D-J2-BT-P-N0
Commissioning
Using the base station in non-explosion-hazardous areas - system
structure 2
1. With a non-explosion-protected base station, charging in non-explosion-hazardous areas can
be performed using the PSU-IDMx61-BC-N0-N0 power supply. The cable is plugged into the
opening for this at the bottom of the base station. For a base station for explosion-hazardous
areas, this connection is sealed at the factory.
Figure 5.9 Connecting the power supply for the non-explosion-hazardous base station.