Pepperl+Fuchs OHV10-F228-R2 User manual

OHV10-F228-R2
1-D/2-D Code Handheld
Reader
Manual

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical ndustry, published by the Central
Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elektroindustrie (ZVE ) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor-
ship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: inf[email protected]s.com
North Ameri an Headquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [email protected]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [email protected]-fuchs.com
https://www.pepperl-fuchs.com

3
OHV10-F228-R2
Contents
2021-01
1 Introdu tion................................................................................................................ 4
1.1 Content of this Do ument............................................................................. 4
1.2 Target Group, Personnel ............................................................................... 4
1.3 Symbols Used ................................................................................................ 5
2 Produ t Des ription .................................................................................................. 6
2.1 Use and Appli ation ...................................................................................... 6
2.2 Indi ators and Operating Elements ............................................................. 7
2.3 Notifi ations ................................................................................................... 7
2.4 A essories.................................................................................................... 7
2.5 Storage and Disposal.................................................................................... 8
3 Installation.................................................................................................................. 9
3.1 Conne tion ..................................................................................................... 9
3.1.1 nstalling/Removing the Cable ............................................................................................ 9
3.1.2 Establishing a USB Connection........................................................................................ 10
3.1.3 Keyboard Mode ................................................................................................................ 10
3.1.4 Establishing an RS-232 Connection ................................................................................. 10
3.2 Installing Devi e Drivers ............................................................................. 11
4 Configuration ........................................................................................................... 12
4.1 Keyboard Layout.......................................................................................... 12
4.2 Configuration Using Control Codes........................................................... 12
4.2.1 Control Codes................................................................................................................... 13
5 Operation.................................................................................................................. 36
5.1 Reading Codes............................................................................................. 36
5.2 Operation Using a Mounting Bra ket......................................................... 37
5.3 Reading Firmware Version and Serial Number ......................................... 39
6 Maintenan e............................................................................................................. 40
7 Troubleshooting....................................................................................................... 41

2021-01
4
OHV10-F228-R2
ntroduction
1 Introdu tion
1.1 Content of this Do ument
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Other documents
1.2 Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.

OHV10-F228-R2
ntroduction
2021-01
5
1.3 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
Informative Symbols
A tion
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

2021-01
6
OHV10-F228-R2
Product Description
2 Produ t Des ription
2.1 Use and Appli ation
The handheld is a compact handheld reader for all common 1-D and 2-D codes. Special tech-
nology to prevent glare allows the device to read codes accurately on highly reflective surfaces.
With a resolution of 1.2 million pixels, it can read small and large codes from a wide range of
distances. A different-colored target projection makes it easier to see the relevant code. The
device responds via a vibration or a visual or audio signal.
Figure 2.1 Handheld reader
The device is only approved for appropriate and intended use. gnoring these instructions will
void any warranty and absolve the manufacturer from any liability.
Use the device only within the specified ambient and operating conditions.
Protection of the personnel and the plant is not ensured if the device is not used according to its
intended use.
Caution!
rritation caused by optical radiation
The optical unit on the handheld reader is equipped with very bright LEDs that can cause irrita-
tion in dark environments.
Do not point the handheld reader at people.
Do not look directly into the optical unit on the handheld reader.

OHV10-F228-R2
Product Description
2021-01
7
2.2 Indi ators and Operating Elements
1. Trigger button
2. Optical unit
3. 10-pin connector socket
4. Function indicator
2.3 Notifi ations
2.4 A essories
1
2
34
A tion Fun tion indi ator Audible signal Vibration
Handheld reader
successfully switched
on
Off Beeps twice Vibrates once
Handheld reader
ready
Off No audible signal No vibration
Code read
successfully
Function indicator briefly lights up
green
Beeps once Vibrates once
Control code read
successfully
Function indicator briefly lights up
green
Beeps twice Vibrates once
Designation Des ription
V45-G-2M-PVC-ABG-
USB-G
Connection cable for USB connection, approx. 1.8 meters
V45-G-2M-PVC-SUBD9 Connection cable for RS-232 connection, approx. 2.4 meters
(extended)
Data connection: Sub-D socket, 9-pin
Power supply: DC connector socket, 5.5 mm
ODZ-MAH-SUPPLY Power supply for RS-232 connection
5 VDC, 1.2 A, short-circuit protected
OHV-BRACKET Table mounting bracket

2021-01
8
OHV10-F228-R2
Product Description
2.5 Storage and Disposal
Keep the original packaging. Always store and transport the device in the original packaging.
Store the device in a clean and dry environment. The permitted ambient conditions must be
considered, see datasheet.
The device, built-in components, packaging, and any batteries contained within must be dis-
posed in compliance with the applicable laws and guidelines of the respective country.

OHV10-F228-R2
nstallation
2021-01
9
3 Installation
3.1 Conne tion
You can connect the handheld reader to the following interfaces.
•USB
•RS-232
3.1.1 Installing/Removing the Cable
Installing the Cable
1. Hold the end of the cable with the RJ50 plug and insert the plug into the RJ50 socket
underneath the handle.
Figure 3.1 nserting the cable
2. Make sure that the cable audibly snaps into place.
Removing the Cable
1. nsert a thin object such as a straightened paper clip into the hole on the side at the bottom of
the handle.
Figure 3.2 Removing the cable
2. Carefully pull the cable and the RJ50 plug out of the handle.

2021-01
10
OHV10-F228-R2
nstallation
3.1.2 Establishing a USB Conne tion
Establishing a USB Conne tion
1. nsert the USB plug on the connection cable into a free USB port on the PC. This step can be
carried out even during operation.
2. When the handheld reader is successfully connected, an audible signal will be emitted and the
handheld reader will vibrate.
The handheld reader is now ready.
3.1.3 Keyboard Mode
A tivating Keyboard Mode
Read the following code using the handheld reader.
Figure 3.3 Keyboard Mode
The function indicator on the handheld reader briefly lights up green.
3.1.4 Establishing an RS-232 Conne tion
Establishing an RS-232 Conne tion
1. Switch off the PC.
2. nsert the RS-232 plug on the connection cable into the RS-232 port on the PC.
3. nsert the low-voltage plug on the power supply unit into the low-voltage socket on the RS-232
connection cable.
4. Connect the mains power plug on the power supply unit to the mains.
5. Switch on the PC.
Once you have switched on the PC, the handheld reader will switch itself on automatically.
6. f the connection is successful, the function indicator lights up green, an acoustic signal
sounds, and the handheld reader vibrates.
The handheld reader is now ready.
7. Read the following code using the handheld reader.
Note
Data is transferred using a US English keyboard layout by default.
f data is not transferred correctly in keyboard mode, modify the keyboard layout.

OHV10-F228-R2
nstallation
2021-01
11
Figure 3.4 RS-232 Connection
The function indicator on the handheld reader lights up green. An RS-232 connection is
established.
The handheld reader uses the following RS-232 factory settings:
•115,200 baud
•8 data bits
•No parity
3.2 Installing Devi e Drivers
The handheld reader registers itself as an input device or keyboard. Special device drivers are
not needed.
The operating system automatically installs the drivers for input devices (Human nterface
Device).

2021-01
12
OHV10-F228-R2
Configuration
4 Configuration
The handheld reader is configured using control codes (see chapter 4.2.1). The control codes
can be used to set the communication mode, general read mode settings, keyboard language,
and other settings of the handheld reader.
4.1 Keyboard Layout
You can use the following control codes to modify the keyboard layout for the current operating
mode.
Mi rosoft Windows
4.2 Configuration Using Control Codes
The handheld reader is configured using control codes. Control codes allow direct configura-
tion without using a PC. To change a parameter, scan the appropriate control code using the
handheld reader.
German (Germany) English (US nternational) French (France)
talian Japanese Russian
Spanish (Spain) Chinese (Simplified) US English (default)

OHV10-F228-R2
Configuration
2021-01
13
4.2.1 Control Codes

2021-01
14
OHV10-F228-R2
Configuration

OHV10-F228-R2
Configuration
2021-01
15

2021-01
16
OHV10-F228-R2
Configuration
Configuration Guide
general-reading-mode-
settings
general-reading-mode-
settings
general-reading-mode-
settings
general-reading-mode-
settings
general-reading-mode-
settings
Continuous Scan Mode On Disable Cell Phone Reading
Enhancement - Default
Disable Target LED During Image
Capture
Disable Targeting-Always-On Enable Cell Phone Reading
Enhancement
Enable Stand Detection -
Default
Enable Target LED During Image
Capture - Default
Enable Targeting-Always-On Motion Detect Always On
Motion Detect or Continuous Scan
Off (Out of Stand) - Default
Motion Detection On In Stand -
Default
No Scan Delay with Motion
Detection in stand
Set Motion Detect Maximum
Brightness to 100% - Default
Reader Raw Text Commands Off
- Default
Reader Raw Text Commands On

OHV10-F228-R2
Configuration
2021-01
17
Configuration Guide
general-reading-mode-
settings
keyboard-language-
settings
keyboard-language-
settings
keyboard-language-
settings
keyboard-language-
settings
Set Motion Detect Maximum
Brightness to 25%
Set Motion Detect Maximum
Brightness to 50%
Set Motion Detect Maximum
Brightness to 75%
Control Character Input -
Alt + Keypad
Control Character Input -
Ctrl + Character
Control Character Input -
Language Default - Default
Control Character Input -
Alt + Leading Zero
Data Encoding: ASCII to Unicode
Codepoint - Alt Sequences for
Windows
Data Encoding: Raw ASCII to
Keyboard XML File Lookup -
Default
Keyboard Support: English
Keyboard Mapping for Apple
Keyboard Support: French
Keyboard Mapping for Apple
Keyboard Support: French
Keyboard Mapping for
Windows
Keyboard Support: French-Belgian
Keyboard Mapping for
Windows

2021-01
18
OHV10-F228-R2
Configuration

OHV10-F228-R2
Configuration
2021-01
19

2021-01
20
OHV10-F228-R2
Configuration