Pepperl+Fuchs CC-LINK Series Installation instructions

CC-LINK GATEWAYS
FACTORY AUTOMATION
COMPACT MANUAL

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical Industry, published by the
Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie
(ZVEI) e.V.) in its most recent version as well as the supplementary clause: "Expanded reservation
of proprietorship".
CC-Link Gateways

3
02.05.2016
CC-Link Gateways
Table of contents
Table of contents
CC-Link Gateways
1 Introduction...........................................................................................5
2 Declaration of conformity....................................................................6
2.1 Declaration of conformity ...............................................................................6
3 Safety.....................................................................................................7
3.1 Symbols relevant to safety ............................................................................. 7
3.2 General notes on safety .................................................................................. 7
3.3 Disposal............................................................................................................ 7
4 Setting up the AS-i bus........................................................................8
5 Configuration and Start-up of the Safety Monitor.............................9
6 Data transmission modes of the CC-Link Gateways.......................10
6.1 Standard mode............................................................................................... 11
6.1.1 Remote IO Points.......................................................................................................... 11
6.1.2 Buffer memory area...................................................................................................... 13
6.1.3 Safety Status ................................................................................................................. 15
6.1.4 Fieldbus Bits.................................................................................................................. 15
6.1.5 Message Transmission................................................................................................. 16
6.2 Compatibility mode for VBG-CCL-G4F ........................................................ 17
6.2.1 Remote IO Points.......................................................................................................... 17
6.2.2 Buffer Memory Area...................................................................................................... 18
6.3 CC-Link V1 Mode ........................................................................................... 22
6.3.1 Remote IO Points.......................................................................................................... 22
6.3.2 Buffer Memory Area...................................................................................................... 23
6.4 Compatibility Mode for FX2N-32ASI-M ........................................................27
6.4.1 Remote IO Points.......................................................................................................... 27
6.4.2 Buffer Memory Area...................................................................................................... 27
6.5 Compatibility Mode for HK-ASICC ............................................................... 30
6.5.1 Remote IO Points.......................................................................................................... 30
6.5.2 Buffer Memory Area...................................................................................................... 30
7 Accessing command interface..........................................................31
7.1 Using BFM ...................................................................................................... 31
7.2 Using "Message Transmission"................................................................... 34

02.05.2016
4
CC-Link Gateways
Table of contents
8 Diagnostics......................................................................................... 36
8.1 System diagnostics on the PC......................................................................36
8.1.1 Software for diagnostics, service and release measurements.................................36
8.1.2 AS-i Control Tools.........................................................................................................36
8.1.3 ASIMON ..........................................................................................................................36
8.1.4 Web server .....................................................................................................................36
8.2 Diagnostics on the host controller...............................................................37
8.2.1 Diagnostics through process data ..............................................................................37
8.2.1.1 Diagnosing the AS-i circuits..........................................................................................37
Flags + Fault Detector (see chap. 6.1.1). ...................................................................37
8.2.1.2 Diagnosing the Safety Monitor......................................................................................37
Safety diagnostics in the Input Data Image ................................................................37
Fieldbus Bits and Safety Status .................................................................................37
Safety diagnostics in the Input Data Image (IDI) 38
Safety diagnostics of safe AS-i inputs ........................................................................38
Safety diagnostics of safe AS-i outputs ......................................................................39
Changing the base setting ..........................................................................................40
8.2.2 Diagnosing the safety unit using the command interface.........................................40
8.2.3 LEDs ...............................................................................................................................40
8.2.4 LC-Display......................................................................................................................40
8.2.5 AS-i Monitor ...................................................................................................................40
8.2.5.1 Duplicate address detection .........................................................................................40
8.2.5.2 Earth fault monitor ........................................................................................................41
8.2.5.3 Noise voltage detection ................................................................................................41
8.2.5.4 Overvoltage detection...................................................................................................41
9 Appendix............................................................................................. 42

5
02.05.2016
CC-Link Gateways
Introduction
1. Introduction
Congratulations
You have chosen a device manufactured by Pepperl+Fuchs. Pepperl+Fuchs de-
velops, produces and distributes electronic sensors and interface modules for the
market of automation technology on a worldwide scale.
Before installing this equipment and put into operation, read this manual carefully.
This manual containes instructions and notes to help you through the installation
and commissioning step by step. This makes sure bring such a trouble-free use
of this product. This is for your benefit, since this:
• ensures the safe operation of the device
• helps you to exploit the full functionality of the device
• avoids errors and related malfunctions
• avoids costs by disruptions and any repairs
• increases the effectiveness and efficiency of your plant
Keep this manual at hand for subsequent operations on the device.
After opening the packaging please check the integrity of the device and the num-
ber of pieces of supplied.
Symbols used
The following symbols are used in this manual:
Contact
If you have any questions about the device, its functions, or accessories, please
contact us at:
Pepperl+Fuchs GmbH
Lilienthalstraße 200
68307 Mannheim
Telephone: [phone]
Fax: [phone]
E-Mail: [email protected]
Information!
This symbol indicates important information.
Attention!
This symbol warns of a potential failure. Non-compliance may lead to interruptions of
the device, the connected peripheral systems, or plant, potentially leading to total mal-
functioning.
Warning!
This symbol warns of an imminent danger. Non-compliance may lead to personal inju-
ries that could be fatal or result in material damages and destruction.

02.05.2016
6
CC-Link Gateways
Declaration of conformity
2. Declaration of conformity
2.1 Declaration of conformity
This product was developed and manufactured under observance of the applica-
ble European standards and guidelines.
The product manufacturer, Pepperl+Fuchs GmbH, D-68307 Mannheim, has a
certified quality assurance system that conforms to ISO 9001.
Information!
A Declaration of Conformity can be requested from the manufacturer.

7
02.05.2016
CC-Link Gateways
Safety
3. Safety
3.1 Symbols relevant to safety
3.2 General notes on safety
Only instructed specialist staff may operate the device in accordance with the op-
erating manual.
User modification and or repair are dangerous and will void the warranty and ex-
clude the manufacturer from any liability. If serious faults occur, stop using the de-
vice. Secure the device against inadvertent operation. In the event of repairs, re-
turn the device to your local Pepperl+Fuchs representative or sales office.
The connection of the device and maintenance work when live may only be car-
ried out by a qualified electrical specialist.
The operating company bears responsibility for observing locally applicable safe-
ty regulations.
Store the not used device in the original packaging. This offers the device optimal
protection against impact and moisture.
Ensure that the ambient conditions comply with regulations.
3.3 Disposal
Information!
This symbol indicates important information.
Attention!
This symbol warns of a potential failure. Non-compliance may lead to interruptions of
the device, the connected peripheral systems, or plant, potentially leading to total mal-
functioning.
Warning!
This symbol warns of an imminent danger. Non-compliance may lead to personal inju-
ries that could be fatal or result in material damages and destruction.
Information!
Electronic waste is hazardous waste. Please comply with all local ordinances when
disposing this product!
The device does not contain batteries that need to be removed before disposing it.

02.05.2016
8
CC-Link Gateways
Setting up the AS-i bus
4. Setting up the AS-i bus
1. Connect the unit to power.
2. Connect the AS-i cable to the unit.
3. One after the other connect the AS-i slaves to the AS-i cable and set the
slave addresses. 
You may set the addresses directly on the slave using a portable addresser
or by using the option [SLAVE ADR TOOL] in the display menu of your
gateway.
4. In the display menu select [QUICK SETUP] to use the configuration of all
AS-i circuits connected to the unit.
Confirm with [STORE+RUN].
5. Set the CC-Link address and connect the gateway to the host fieldbus con-
troller. 
You can set the addresses directly using the option [CC-LINK] in the dis-
play menu of your gateway or through the PC using the ASIMON software
with integrated AS-i Control Tools.
For more detailed information please refer to the installation guide for your gateway
which is included with the unit.

9
02.05.2016
CC-Link Gateways
Configuration and Start-up of the Safety Monitor
5. Configuration and Start-up of the Safety Monitor
Configuration and start-up of the AS-i Safety Monitor is accomplished using a PC/
notebook running the ASIMON configuration software.
Configuration should be performed only by a safety specialist. All safety-related
commands are password protected.
Note!
For more detailed information please refer to the separate manual for the ASIMON
configuration software.
The correct safety functioning of the unit must absolutely be verified in the system!
Note!
Quick Start Guides for commissioning and service are provided on the website availa-
ble for download.

02.05.2016
10
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6. Data transmission modes of the CC-Link Gateways
There are several modes for the transmission of data in CC-Link:
1. Standard mode (see chap. 6.1)
2. Compatibility mode for VBG-CCL-G4F COMP (see chap. 6.2)
3. Compatibility mode for CC-Link V1 (see chap. 6.3)
4. Compatibility mode for FX2N-32ASI-M CP (see chap. 6.4)
5. Compatibility mode for HK-ASICC COMP (see chap. 6.5)
Information!
The selection of each data transmission mode takes place in the menu of the gateway
using the buttons and the display. Additional information can be foand in the descrip-
tion of the display menu of your gateway.
Summary of data transmission modes
Standard VBG-CCL-
G4F CC-Link V1 FX2N- 32ASI-M HK- ASICC
occupied stations 3 3 4 4 2
cycle setting 2 1 1 1 1
required CC-Link master V2 V1 V1 V1 V1
support of 2 AS-i circuits no no no no no
support of B-slaves yes (yes) yes no no
support of analog slaves yes yes yes no no
support of AS-i configuration
via CC-Link yes yes yes no no
Tab. 6-1.

11
02.05.2016
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.1 Standard mode
The Standard Mode has the following features:
• the gateway occupies 3 stations and has a double cycle setting.
• The last 2 words are reserved for "Message Transmission".
• The AS-i process data is mapped into the Buffer Memory Area (BFM).
• All acyclic requests are handled by "Message Transmission" using cyclic
data.
6.1.1 Remote IO Points
Remote to Host
Address 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXm reserved
RXm+1 AS-i circuit 1: EC-Flags and Fault Detector
RXm+2 reserved…
RXm+9
Tab. 6-2.
EC-Flags and Fault Detector
Bit Short Cut Name
0 Cfg. OK Configuration OK
1S0 Slave Address 0 detected
2 Aaasn Auto Address Assign
3Aaavail Auto Address Available
4 CM Configuration Mode active
5NA Normal Operation active
6 APF AS-i Power Fail (AS-i voltage below 19 V)
7Offl Off-line
8 NPF No Peripheral Fault
9reserved reserved
10 PWRw Power Warning (AS-i voltage below 22.5 V)
11 reserved reserved
12 EF Earth Fault
13 OV Over-voltage on AS-i
14 Noise Noise
15 reserved reserved
Tab. 6-3.

02.05.2016
12
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
Host to Remote
Address 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RYm PM CM AAE OFL
RYm+1 reserved
…
RYm+9
Tab. 6-4.
Flags in RYm
Bit Short Cut Name
0 OFL Offline
1AAE Auto Address Enable
2 CM Enter Configuration Mode on rising edge
3PM Enter Protected Mode on rising edge
4 … 15 reserved
Tab. 6-5.

13
02.05.2016
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.1.2 Buffer memory area
Buffer memory
for master without integr. safety monitor
Address 1 Master
read write
0 … 7 AS-i 1, input A + single slaves AS-i 1, output A + single slaves
8 … 15 AS-i 1, input B slaves AS-i 1, output B slaves
16 … 23 reserved
Tab. 6-6.
Buffer memory (read)
for master with integr. safety monitor
Address Bit 15 … 12 Bit 11 … 8 Bit 7 … 4 Bit 3 … 0
RWrm0 AS-i 1: Inp. Slv3 AS-i 1: Inp. Slv2 AS-i 1: Inp. Slv1 flags AS-i 1
RWrm1 AS-i 1: Inp. Slv7 AS-i 1: Inp. Slv6 AS-i 1: Inp. Slv5 AS-i 1: Inp. Slv4
RWrm2 AS-i 1: Inp. Slv11 AS-i 1: Inp. Slv10 AS-i 1: Inp. Slv9 AS-i 1: Inp. Slv8
RWrm3 AS-i 1: Inp. Slv15 AS-i 1: Inp. Slv14 AS-i 1: Inp. Slv13 AS-i 1: Inp. Slv12
RWrm4 AS-i 1: Inp. Slv19 AS-i 1: Inp. Slv18 AS-i 1: Inp. Slv17 AS-i 1: Inp. Slv16
RWrm5 AS-i 1: Inp. Slv23 AS-i 1: Inp. Slv22 AS-i 1: Inp. Slv21 AS-i 1: Inp. Slv20
RWrm6 AS-i 1: Inp. Slv27 AS-i 1: Inp. Slv26 AS-i 1: Inp. Slv25 AS-i 1: Inp. Slv24
RWrm7 AS-i 1: Inp. Slv31 AS-i 1: Inp. Slv30 AS-i 1: Inp. Slv29 AS-i 1: Inp. Slv28
RWrm8 AS-i 1: Inp. Slv3B AS-i 1: Inp. Slv2B AS-i 1: Inp. Slv1B
RWrm9 AS-i 1: Inp. Slv7B AS-i 1: Inp. Slv6B AS-i 1: Inp. Slv5B AS-i 1: Inp. Slv4B
RWrm10 AS-i 1:
Inp. Slv11B AS-i 1: Inp. Slv10B AS-i 1: Inp. Slv9B AS-i 1: Inp. Slv8B
RWrm11 AS-i 1:
Inp. Slv15B AS-i 1: Inp. Slv14B AS-i 1: Inp. Slv13B AS-i 1: Inp. Slv12B
RWrm12 AS-i 1:
Inp. Slv19B AS-i 1: Inp. Slv18B AS-i 1: Inp. Slv17B AS-i 1: Inp. Slv16B
RWrm13 AS-i 1:
Inp. Slv23B AS-i 1: Inp. Slv22B AS-i 1: Inp. Slv21B AS-i 1: Inp. Slv20B
RWrm14 AS-i 1: Inp.
Slv27B AS-i 1: Inp. Slv26B AS-i 1: Inp. Slv25B AS-i 1: Inp. Slv24B
RWrm15 AS-i 1:
Inp. Slv31B AS-i 1: Inp. Slv30B AS-i 1: Inp. Slv29B AS-i 1: Inp. Slv28B
RWrm16 fieldbus bits 15 … 8 fieldbus bits 7 … 0
RWrm17 Safety Status OSSD2 Safety Status OSSD1
RWrm18 Safety Status OSSD4 Safety Status OSSD3
RWrm19 Safety Status OSSD6 Safety Status OSSD5
Tab. 6-7.

02.05.2016
14
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
Bits in flags
Bit Name
0 0: No Config Error
1 0: AS-i Power OK
2 0: Normal Operation active
3 0: Protected Mode active
Tab. 6-8.
Buffer memory (write)
for master with integr. safety monitor
Address Bit 15 … 12 Bit 11 … 8 Bit 7 … 4 Bit 3 … 0
RWwm0 AS-i 1: Outp. Slv3 AS-i 1: Outp. Slv2 AS-i 1: Outp. Slv1
RWwm1 AS-i 1: Outp. Slv7 AS-i 1: Outp. Slv6 AS-i 1: Outp. Slv5 AS-i 1: Outp. Slv4
RWwm2 AS-i 1: Outp.
Slv11 AS-i 1: Outp. Slv10 AS-i 1: Outp. Slv9 AS-i 1: Outp. Slv8
RWwm3 AS-i 1:
Outp. Slv15 AS-i 1: Outp. Slv14 AS-i 1: Outp. Slv13 AS-i 1: Outp. Slv12
RWwm4 AS-i 1:
Outp. Slv19 AS-i 1: Outp. Slv18 AS-i 1: Outp. Slv17 AS-i 1: Outp. Slv16
RWwm5 AS-i 1:
Outp. Slv23 AS-i 1: Outp. Slv22 AS-i 1: Outp. Slv21 AS-i 1: Outp. Slv20
RWwm6 AS-i 1:
Outp. Slv27 AS-i 1: Outp. Slv26 AS-i 1: Outp. Slv25 AS-i 1: Outp. Slv24
RWwm7 AS-i 1:
Outp. Slv31 AS-i 1: Outp. Slv30 AS-i 1: Outp. Slv29 AS-i 1: Outp. Slv28
RWwm8 AS-i 1:
Outp. Slv3B AS-i 1: Outp. Slv2B AS-i 1: Outp. Slv1B
RWwm9 AS-i 1:
Outp. Slv7B AS-i 1: Outp. Slv6B AS-i 1: Outp. Slv5B AS-i 1: Outp. Slv4B
RWwm10 AS-i 1:
Outp. Slv11B AS-i 1: Outp. Slv10B AS-i 1: Outp. Slv9B AS-i 1: Outp. Slv8B
RWwm11 AS-i 1:
Outp. Slv15B AS-i 1: Outp. Slv14B AS-i 1: Outp. Slv13B AS-i 1: Outp. Slv12B
RWwm12 AS-i 1:
Outp. Slv19B AS-i 1: Outp. Slv18B AS-i 1: Outp. Slv17B AS-i 1: Outp. Slv16B
RWwm13 AS-i 1:
Outp. Slv23B AS-i 1: Outp. Slv22B AS-i 1: Outp. Slv21B AS-i 1: Outp. Slv20B
RWwm14 AS-i 1:
Outp. Slv27B AS-i 1: Outp. Slv26B AS-i 1: Outp. Slv25B AS-i 1: Outp. Slv24B
RWwm15 AS-i 1:
Outp. Slv31B AS-i 1: Outp. Slv30B AS-i 1: Outp. Slv29B AS-i 1: Outp. Slv28B
RWwm16 fieldbus bits 15 … 8 fieldbus bits 7 … 0
…reserved
RWwm19
Tab. 6-9.

15
02.05.2016
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.1.3 Safety Status
6.1.4 Fieldbus Bits
The fieldbus bits enable communication between the controller and the safety
program. The fieldbus bits can be used to pass any acknowledgment signals or
similar to the safety program and provide status information to the controller.
The states of the AS-i Safety in- and outputs are sent to the controller via the in-
put data image (see par. <Safety diagnostics in the Input Data Image (IDI)>).
Bits in flags
Bit Name
0 0: No Config Error
1 0: AS-i Power OK
2 0. Normal Operation active
3 0: Protected Mode active
Tab. 6-10.
Bits in Safety Status
Bit 2726252423222120
one or more
devices are red
flashing
one or more
devices are yellow
flashing reserved
OSSD Color
0: green
1: flashing green
2: yellow
3: yellow flashing
4: red
5: flashing red
6: grey
7: reserved
Tab. 6-11. Bits in Safety Status
Information!
This functionality is only available in devices in the safety version ’SV 4.3’ (see lateral
label)!
Output data (device fieldbus bit in ASIMON)
215 214 213 212 211 210 29282726252423222120
FB15 FB14 FB13 FB12 FB11 FB10 FB09 FB08 FB07 FB06 FB05 FB04 SI4SI3SI2SI1
Tab. 6-12.
Input data (output assignment fieldbus bit in ASIMON)
215 214 213 212 211 210 29282726252423222120
FB15 FB14 FB13 FB12 FB11 FB10 FB09 FB08 FB07 FB06 FB05 FB04 FB03 FB02 FB01 FB00
Tab. 6-13.
FB: fieldbus bit
SI1 … SI4: monitor inputs

02.05.2016
16
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.1.5 Message Transmission
"Message Transmission" provides only command interface commands (see se-
parate manual "AS-i 3.0 Command Interface").
Information!
More detailed information can be found in the manual "ASIMON configuration soft-
ware", sections: "Monitoring devices -> Fieldbus bit" and "Output assignment"..
Information!
For details on the Message Transmission protocol, please refer to the CC-Link specifi-
cation. For more information or PLC program examples, how to use Message Trans-
mission, please refer to the documentation of your CC-Link master in use.

17
02.05.2016
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.2 Compatibility mode for VBG-CCL-G4F
The Compatibility Mode for VBG-CCL-G4F has the following features:
• 3 stations are occupied using a single cycle setting.
• All functions of VBG-CCL-G4F are implemented.
• The AS-i process data or the command interface is mapped into the buffer
memory area (BFM) (as done in the VBG-CCL-G4F).
• "Message Transmission" is not supported 
(since VBG-CCL-G4F also does not use it).
6.2.1 Remote IO Points
Remote to Host
Address 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXm reserved BfEAck MbAck reserved
RXm+1
…
RXm+5 reserved
Tab. 6-14.
Flags in RXm
Bit Short Cut Name
0 … 3 reserved
4 MbAck Acknowledge bit for Y4
5 BfEAck Acknowledge bit for Y5
6 … 15 reserved
Tab. 6-15.
Host to Remote
Address 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RYm reserved BfE Mb PM CM AAE OFL
RYm+1
…
RYm+5 reserved
Tab. 6-16.

02.05.2016
18
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
6.2.2 Buffer Memory Area
Flags in RYm
Bit Short Cut Name
0 OFL Offline
1 AAE Auto Address Enable
2 CM Enter Configuration Mode on rising edge
3 PM Enter Protected Mode on rising edge
4 Mb 0: BFM used for IO data only 
1: BFM used for command interface
5 BfE 0: Enable use of BFM
6 … 15 reserved
Tab. 6-17.
Buffer memory (read) when using ’IO data only mode’
Address Bit 15 … 12 Bit 11 … 8 Bit 7 … 4 Bit 3 … 0
RWrm0 AS-i 1: Inp. Slv3 AS-i 1: Inp. Slv2 AS-i 1: Inp. Slv1 flags
RWrm1 AS-i 1: Inp. Slv7 AS-i 1: Inp. Slv6 AS-i 1: Inp. Slv5 AS-i 1: Inp. Slv4
RWrm2 AS-i 1:
Inp. Slv11 AS-i 1: Inp. Slv10 AS-i 1: Inp. Slv9 AS-i 1: Inp. Slv8
RWrm3 AS-i 1:
Inp. Slv15 AS-i 1: Inp. Slv14 AS-i 1: Inp. Slv13 AS-i 1: Inp. Slv12
RWrm4 AS-i 1:
Inp. Slv19 AS-i 1: Inp. Slv18 AS-i 1: Inp. Slv17 AS-i 1: Inp. Slv16
RWrm5 AS-i 1:
Inp. Slv23 AS-i 1: Inp. Slv22 AS-i 1: Inp. Slv21 AS-i 1: Inp. Slv20
RWrm6 AS-i 1:
Inp. Slv27 AS-i 1: Inp. Slv26 AS-i 1: Inp. Slv25 AS-i 1: Inp. Slv24
RWrm7 AS-i 1:
Inp. Slv31 AS-i 1: Inp. Slv30 AS-i 1: Inp. Slv29 AS-i 1: Inp. Slv28
RWrm8 AS-i 1:
Inp. Slv3B AS-i 1: Inp. Slv2B AS-i 1: Inp. Slv1B
RWrm9 AS-i 1:
Inp. Slv7B AS-i 1: Inp. Slv6B AS-i 1: Inp. Slv5B AS-i 1: Inp. Slv4B
RWrm10 AS-i 1:
Inp. Slv11B AS-i 1: Inp. Slv10B AS-i 1: Inp. Slv9B AS-i 1: Inp. Slv8B
RWrm11 AS-i 1:
Inp. Slv15B AS-i 1: Inp. Slv14B AS-i 1: Inp. Slv13B AS-i 1: Inp. Slv12B
Tab. 6-18.
Bits in Flags
Bit Name
0 0: No Config Error
1 0: AS-i Power OK
2 0. Normal Operation active
3 0: Protected Mode active
Tab. 6-19.

19
02.05.2016
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
Buffer memory (read) when using ’command interface mode’
Address Bit 15 … 12 Bit 11 … 8 Bit 7 … 4 Bit 3 … 0
RWrm0 command interface:
circuit command interface: command
RWrm1 command interface:
response byte 2 command interface: response byte 1
RWrm2 command interface:
response byte 4 command interface: response byte 3
RWrm3 command interface:
response byte 6 command interface: response byte 5
RWrm4 command interface:
response byte 8 command interface: response byte 7
RWrm5 command interface:
response byte 10 command interface: response byte 9
RWrm6 command interface:
response byte 12 command interface: response byte 11
RWrm7 command interface:
response byte 14 command interface: response byte 13
RWrm8 command interface:
response byte 16 command interface: response byte 15
RWrm9 command interface:
response byte 18 command interface: response byte 17
RWrm10 command interface:
response byte 20 command interface: response byte 19
RWrm11 command interface:
response byte 22 command interface: response byte 21
Tab. 6-20.

02.05.2016
20
CC-Link Gateways
Data transmission modes of the CC-Link Gateways
Buffer memory (write) when using ’IO data only mode’
Address Bit 15 … 12 Bit 11 … 8 Bit 7 … 4 Bit 3 … 0
RWwm0 AS-i 1:
Outp. Slv3 AS-i 1: Outp. Slv2 AS-i 1: Outp. Slv1 flags
RWwm1 AS-i 1:
Outp. Slv7 AS-i 1: Outp. Slv6 AS-i 1: Outp. Slv5 AS-i 1: Outp. Slv4
RWwm2 AS-i 1:
Outp. Slv11 AS-i 1: Outp. Slv10 AS-i 1: Outp. Slv9 AS-i 1: Outp. Slv8
RWwm3 AS-i 1:
Outp. Slv15 AS-i 1: Outp. Slv14 AS-i 1: Outp. Slv13 AS-i 1: Outp. Slv12
RWwm4 AS-i 1:
Outp. Slv19 AS-i 1: Outp. Slv18 AS-i 1: Outp. Slv17 AS-i 1: Outp. Slv16
RWwm5 AS-i 1:
Outp. Slv23 AS-i 1: Outp. Slv22 AS-i 1: Outp. Slv21 AS-i 1: Outp. Slv20
RWwm6 AS-i 1:
Outp. Slv27 AS-i 1: Outp. Slv26 AS-i 1: Outp. Slv25 AS-i 1: Outp. Slv24
RWwm7 AS-i 1:
Outp. Slv31 AS-i 1: Outp. Slv30 AS-i 1: Outp. Slv29 AS-i 1: Outp. Slv28
RWwm8 AS-i 1:
Outp. Slv3B AS-i 1: Outp. Slv2B AS-i 1: Outp. Slv1B
RWwm9 AS-i 1:
Outp. Slv7B AS-i 1: Outp. Slv6B AS-i 1: Outp. Slv5B AS-i 1: Outp. Slv4B
RWwm10 AS-i 1:
Outp. Slv11B AS-i 1: Outp. Slv10B AS-i 1: Outp. Slv9B AS-i 1: Outp. Slv8B
RWwm11 AS-i 1:
Outp. Slv15B AS-i 1: Outp. Slv14B AS-i 1: Outp. Slv13B AS-i 1: Outp. Slv12B
Tab. 6-21.