Pepperl+Fuchs ICE1 G60L-V1D Series User manual

R
ICE1-*-G60L-V1D,
ICE1-*-G60L-C1-V1D
Fieldbus Modules with
Multiprotocol Tech ology
Ma ual

With regard to the supply of products, the current issue of the following document is applicable: The
General Terms of Delivery for Products and Services of the Electrical ndustry, published by the Central
Association of the Electrical ndustry (Zentralverband Elektrotechnik und Elektroindustrie (ZVE ) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietor-
ship"
Worldwide
Pepperl+Fuchs Group
Lilienthalstr. 200
68307 Mannheim
Germany
Phone: [phone] - 0
E-mail: [email protected]epperl-fuchs.com
North America Headquarters
Pepperl+Fuchs nc.
1600 Enterprise Parkway
Twinsburg, Ohio 44087
USA
Phone: [phone]
E-mail: [e-mail]
Asia Headquarters
Pepperl+Fuchs Pte. Ltd.
P+F Building
18 Ayer Rajah Crescent
Singapore 139942
Phone: [phone]
E-mail: [e-mail]
https://www.pepperl-fuchs.com

3
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Contents
2019-10
1 Safety .......................................................................................................................... 5
1.1 I troductio .................................................................................................... 5
1.1.1 Content of this Document .................................................................. 5
1.1.2 Manufacturer...................................................................................... 5
1.1.3 Target Group, Personnel .................................................................... 5
1.1.4 Symbols Used ................................................................................... 6
2 Product Descriptio .................................................................................................. 7
2.1 Use a d Applicatio ...................................................................................... 7
2.2 Displays a d Operati g Eleme ts................................................................ 9
2.3 I terfaces a d Co ectio s .......................................................................12
2.4 Dime sio s................................................................................................... 14
3 I stallatio ................................................................................................................ 15
3.1 Ge eral I formatio ..................................................................................... 15
4 Commissio i g, Protocol Setti g .......................................................................... 17
4.1 Setti g Protocols ......................................................................................... 17
5 Commissio i g for EtherNet/IP ............................................................................. 19
5.1 Preparatio ................................................................................................... 19
5.2 Co figuratio ............................................................................................... 20
5.2.1 16D O Modules, Connections and Assembly Objects ..................... 21
5.2.2 16D Modules, Connections and Assembly Objects ........................ 25
5.2.3 8D /8DO Modules, Connections and Assembly Objects.................. 26
5.2.4 Configuration Parameters ................................................................ 26
5.2.5 Configuration Example..................................................................... 33
5.3 Bit Assig me t of Process Data ................................................................40
5.3.1 16D O Modules, Bit Assignment of Process Data............................ 40
5.3.2 Modules with Decentralized Control Function, Bit Assignment of Pro-
cess Data Extension42
5.3.3 16D Modules, Bit Assignment of Process Data............................... 43
5.3.4 8D /8DO Modules, Bit Assignment of Process Data ........................ 44
6 Commissio i g for PROFINET ............................................................................... 46
6.1 Preparatio ................................................................................................... 46
6.2 Co figuratio ............................................................................................... 46

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Contents
4
2019-10
6.3 Assig i g Process Data..............................................................................60
6.3.1 16D O Modules, Bit Assignment of Process Data ............................60
6.3.2 Modules with Decentralized Control Function, Bit Assignment of Pro-
cess Data Extension63
6.3.3 16D Modules, Bit Assignment of Process Data ...............................64
6.3.4 8D /8DO Modules, Bit Assignment of Process Data......................... 64
7 Commissio i g for EtherCAT .................................................................................66
7.1 Preparatio ...................................................................................................66
7.2 Co figuratio ................................................................................................66
7.2.1 16D O Modules, PDO Mapping........................................................66
7.2.2 Modules with Decentralized Control Function, Bit Assignment of Pro-
cess Data Extension79
7.2.3 16D Modules, PDO Assignment......................................................80
7.2.4 8D 8DO Modules, PDO Assignment ................................................82
7.2.5 Device Parameters ...........................................................................86
7.2.6 Configuration Example with TwinCAT® 3.......................................... 91
8 The I tegrated Web Server ...................................................................................107
8.1 Overview a d Module Addressi g ...........................................................107
8.2 Me u Structure...........................................................................................107
8.3 Readi g Out the Process a d Diag ostic Data (JSON) .........................115
9 Dece tralized Co trol Fu ctio ............................................................................120
9.1 Basic I formatio .......................................................................................120
9.2 LDMicro Programmi g Tool ......................................................................124
9.3 DCU Web I terface.....................................................................................130
10 Firmware Update:...................................................................................................136
11 Troubleshooti g .....................................................................................................140
11.1 Ge eral Diag ostic Processi g................................................................140
11.2 Diag ostics I dicator i the I tegrated Web Server ..............................141
11.3 Module Diag ostic I formatio via EtherNet/IP .....................................142
11.4 Alarm Sig als a d Error Messages from Modules via PROFINET........142
11.5 Alarm Sig als a d Error Messages from Modules via EtherCAT..........144

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Safety
2019-10
5
1 Safety
1.1 I troductio
1.1.1 Co te t of this Docume t
This document contains information required to use the product in the relevant phases of the
product life cycle. This may include information on the following:
•Product identification
•Delivery, transport, and storage
•Mounting and installation
•Commissioning and operation
•Maintenance and repair
•Troubleshooting
•Dismounting
•Disposal
The documentation comprises the following parts:
•This document
•Datasheet
n addition, the documentation may comprise the following parts, if applicable:
•EU-type examination certificate
•EU declaration of conformity
•Attestation of conformity
•Certificates
•Control drawings
•nstruction manual
•Other documents
1.1.2 Ma ufacturer
1.1.3 Target Group, Perso el
Responsibility for planning, assembly, commissioning, operation, maintenance, and dismount-
ing lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation, com-
missioning, operation, maintenance, and dismounting of the product. The personnel must have
read and understood the instruction manual and the further documentation.
Prior to using the product make yourself familiar with it. Read the document carefully.
Note
For full information on the product, refer to the further documentation on the nternet at
www.pepperl-fuchs.com.
Pepperl+Fuchs Group
Lilienthalstraße 200, 68307 Mannheim, Germany
nternet: www.pepperl-fuchs.com

2019-10
6
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Safety
1.1.4 Symbols Used
This document contains symbols for the identification of warning messages and of informative
messages.
War i g Messages
You will find warning messages, whenever dangers may arise from your actions. t is mandatory
that you observe these warning messages for your personal safety and in order to avoid prop-
erty damage.
Depending on the risk level, the warning messages are displayed in descending order as fol-
lows:
I formative Symbols
Actio
This symbol indicates a paragraph with instructions. You are prompted to perform an action or
a sequence of actions.
Da ger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
War i g!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Cautio !
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants, or result in
their complete failure.
Note
This symbol brings important information to your attention.

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
2019-10
7
2 Product Descriptio
2.1 Use a d Applicatio
Module Descriptio
The CE1-*-G60L-*- modules function as an interface in an industrial fieldbus system. They
enable communication between a central controller at the control level and the decentralized
sensors and actuators at the field level. To do so, in addition to the fieldbus interface, different
variants of the modules have a different number of ports for digital inputs and outputs.
The following module types are described in this manual:
•Ethernet O module with fixed number of inputs/outputs
8D 8DO modules
•CE1-8D 8DO-G60L-V1D: Ethernet O module with 8 digital inputs (8D ) and 8 digital
outputs (8DO)
•CE1-8D 8DO-G60L-C1-V1D: Ethernet O module with 8 digital inputs (8D ), 8 digital
outputs (8DO) and decentralized control function
16D modules
•CE1-16D -G60L-V1D: Ethernet O module with 16 digital inputs (16D )
•Ethernet O module with configurable inputs/outputs
16D O modules
•CE1-16D O-G60L-V1D: Ethernet O module with 16 digital inputs/outputs (16D O),
freely configurable
•CE1-16D O-G60L-C1-V1D: Ethernet O module with 16 digital inputs/outputs
(16D O), freely-configurable and decentralized control function
The modules have an integrated 2-port switch, have multiprotocol capability and can be config-
ured for EtherNet/ P, PROF NET, or EtherCAT. The resulting potential line or ring topologies that
can be achieved enable reliable data communication and a significant reduction in the amount
of wiring required, which therefore makes the costs for installation and maintenance reason-
able. Simple and rapid extension is also possible.
The CE1-*-G60L-* series modules have a robust metal housing made of die-cast zinc. Due to
the fully encapsulated device housing, the module electronics are protected against environ-
mental influences and can be used in a wide range of temperatures. Despite the robust design,
the modules have compact dimensions and a low weight. They are especially suitable for use
in machines and plants with a moderate /O concentration on distributed assemblies.
Multiprotocol (EtherNet/IP, PROFINET, or EtherCAT)
The Ethernet O modules are multiprotocol modules and allow you to select one of many differ-
ent protocols for communication within a fieldbus system. As a result, multiprotocol modules
can be integrated into different networks without the need to purchase protocol-specific mod-
ules. Thanks to this technology, you can also use one and the same module in different envi-
ronments.
Using rotary coding switches in the lower area of the modules, you can comfortably and easily
set both the protocol and the address of the module, provided the protocol to be used supports
this. f you have chosen a protocol and started the cyclic communication once, the module
remembers this setting and uses the selected protocol from this point on. To use another sup-
ported protocol with this module, perform a factory reset.

2019-10
8
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
Special Product Features
•Robust desig
Connectivity options for the module series include the widespread M12 connector with A
encoding for /O signals and D coding for the network. n addition, the connectors are
color-coded to prevent confusion of the ports. The output circuits are galvanically isolated
from the rest of the network and the sensor electronics. Controllers are therefore reliably
protected against noise. This does not apply to the 16D O modules due to the configu-
rable inputs/outputs.
•I tegrated web server
Network parameters such as P address, subnet mask, and gateway can be adjusted via
control switches (last byte of the P address) or the integrated web server. The modules
support the communication protocols BOOTP and DHCP for automated assignment of
network parameters via the corresponding servers.
•I tegrated etwork switch
The integrated 2-port Ethernet switch of the modules allows you to set up a line topology
for an EtherCAT® network or a ring topology for the EtherNet/ P network or PROF NET
network. The additionally implemented DLR or MRP protocol allows you to design a
highly available network infrastructure.
•Redu da cy fu ctio
The module firmware supports the redundancy function DLR (Device Level Ring) or MRP
(Media Redundancy Protocol) for ring topologies. This means that if the connection is
interrupted, the modules switch to an alternative ring segment and thus ensure interrup-
tion-free operation. The DLR class supported is "beacon-based" in accordance with the
EtherNet/ P specification.
•Fail-safe fu ctio
The modules with output functionality offer a fail-safe function. You can therefore choose
the behavior of each individual output channel in the event of an interruption or a loss of
communication.
•QuickCo ect
QuickConnect allows the modules to record the communication in an EtherNet/ P network
particularly quickly through an accelerated boot-up process. This allows you to switch
tools more quickly, for example.
•Force Mode
"Force Mode" allows the simulation of process data at the inputs/outputs without the need
to connect sensors and actuators. This means you can test an application in advance
without a full physical application. t is possible to simulate input switching states or to
switch outputs even without a controller. This feature eases and accelerates machine
commissioning and can be used to test new production plants.
•Dece tralized co trol fu ctio o C1 modules
CE1-*-G60L-C1-V1D modules with decentralized control function (DCU) can control
applications independently using an integrated programmable logic. They can therefore
run timers, counters and other functions and can optionally exchange data with a higher-
level controller. The program's residual storage is ideal for plug and play operation. This
allows installation and maintenance of these modules to be quick and intuitive. Details on
programming the decentralized control function can be found in the chapter "Decentral-
ized Control Function.”
•Flex-Bit tech ology o 16DIO modules (IO mappi g):
With Flex-Bit-technology, it is possible to change the O mapping of process data. As a
rule, each channel is statically assigned to a bit in the process data. This function allows
the data direction of a channel to be determined, along with its process data bit assign-
ment. By configuring the O mapping, it is therefore possible to operate Ethernet O mod-
ules in applications with bit mappings from other manufacturers.

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
2019-10
9
•Automatic co figuratio of i puts/outputs o 16DIO modules via i put/output
profiles
The 16D O modules can be used universally and offer a variety of input/output profiles as
basic configuration. By selecting a predefined profile, you can very easily preconfigure a
16D O module as, among other things, a 16D , 16DO, or 8D 8DO module. This allows
quick and easy replacement of existing modules within the plant.
2.2 Displays a d Operati g Eleme ts
1LED channel indicator
2LED status indicator
3Rotary switch
20X10X
X03
X4 X8
7X
3
X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
X02X01
US UL
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
RUN ERR
0E/IP
P
00
FM
C
MS NSE/IP:
P:
EC:
EC
1
2
3
Note
The LEDs in the lower area of the Ethernet O module have different names and functions
depending on the selected protocol. The following LED descriptions are therefore divided into
a general part (1), which is valid for all protocol settings, and LED descriptions for a specific
protocol setting (2).
Figure 2.1
•E/ P: EtherNet/ P
•P: PROF NET
•EC: EtherCAT
1
2

2019-10
10
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
Displays - Ge eral Part
Description for LED A, B, D A, U
S
, U
S
, DCU/FM
EtherNet/IP Displays
E/ P area: relevant LEDs Lnk/Act, MS, NS
LED Fu ctio
LED A (for each of X1
- X8)
D A
White: channel A status is "on”
Off: no error, not connected
Red: peripheral error (sensor/actuator overload or short circuit)
LED B X1 - X8 B
D A
White: channel B status is "on”
Off: no error, not connected
Red: peripheral error (sensor/actuator overload or short circuit)
LED U
S
Green: voltage 19 V  U
S
 30 V
Red: voltage U
S
< 19 V or U
S
> 30 V
LED U
L1
1. Only 8D 8DO and 16D O
Green: voltage 19 V  U
L
 30 V
Red: voltage U
L
< 19 V or U
L
> 30 V
LED C/FM
Only CE1-8D 8DO-
G60L-C1-V1D
And CE1-16D O-
G60L-C1-V1D
Blue: DCU function is stopped
Flashing blue: DCU function is working
Off: DCU function not active; Force Mode disabled
Flashing red: DCU function error
Flashing blue/red: Force Mode enabled
LED FM
For modules without
decentralized control
function (C1 modules)
Off: Force Mode disabled
Flashing blue/red: Force Mode enabled
Table 2.1
LED Fu ctio
LED Lnk/Act Green: connection to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED MS Green: module ready for operation
Flashing green: missing configuration
Flashing red/green: self-test
Red: non-recoverable, serious error
Flashing red: minor recoverable error (e.g., incorrect configuration)
Off: module switched off
LED NS Green: module has at least one connection
Flashing green: module has no connections P address is available
Red/green: module is performing a self-test
Red: module has determined that the assigned P address already
exists
Off: module is turned off or does not have an P address
Table 2.2

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
2019-10
11
PROFINET Displays
P area: relevant LEDs Lnk/Act, BF, D A
EtherCAT Displays
EC area: relevant LEDs X01, X02 , RUN, ERR
Operati g Eleme ts
LED Fu ctio
LED Lnk/Act Green: connection to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED BF Red: no configuration, slow or no physical connection
Flashing red: no data exchange with O device
Off: no error
LED D A Red: watchdog timeout or diagnosis occurring, or system error
Flashing red for 3 sec: DCP signal service triggered via the bus
Off: no error
Table 2.3
LED Fu ctio
LED X01 Green: connection to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED X02 Green: connection to an Ethernet node
Flashing yellow: data exchange with an O device
Off: no connection
LED RUN Green: OPERAT ONAL status
1 x flashing green: SAFE OPERAT ONAL status
Flashing green: PRE-OPERAT ONAL status
Flickering green: module is starting up and is not yet in N T state, or
module is in BOOTSTRAP state and is loading firmware.
Off: N T status
LED ERROR Red: control error, e.g., PD watchdog timeout
Flickering: error during booting
Flashing red: incorrect configuration; general configuration error
1 x flashing red: local error, undesired status change
2 x flashing red: watchdog error
Off: no error
Switch Fu ctio
Rotary switch X100 Setting the fieldbus protocol
Setting the P address
1
1. Only EtherNET/ P
Rotary switch X10 Setting the P address
Rotary switch X1 Setting the P address
Note
Details on setting the protocol and the P address can be found in the chapter "Commissioning,
Protocol Setting”

2019-10
12
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
2.3 I terfaces a d Co ectio s
The contact arrangements below show the front view of the plug-in area of the connectors.
Fieldbus Co ectio X01, X02
•Connection: M12 socket, 4 pin, D-coded
•Color coding: green
Figure 2.2 Schematic drawing of port X01, X02
Co ectio for Power Supply X03, X04
•Power supply with M12 power L-coded
•Color coding: gray
Figure 2.3 Schematic drawing of M12 L-encoding (plug); port X03 ( N)
Port Pi Sig al Fu ctio
Ports X01, X02 1 TD+ Transmit data +
2 RD+ Receive data +
3 TD- Transmit data -
4 RD- Receive Data -
Table 2.4 Assignment of port X01, X02
1
3
2
4
Cautio !
Risk of destruction!
Never route the power supply to the data cable.
Cautio !
Loss of function when the system supply voltage is too low.
Ensure in all cases that the supply voltage measured at the most remote participants (sen-
sor/actuator) does not drop below 18 V DC in terms of system supply voltage.
Note
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary supply via U
L
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the Ethernet O module can continue working even if there is a failure of the load power supply.
Where several Ethernet O modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
L
.
4
1
3
2
FE

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
2019-10
13
Figure 2.4 Schematic drawing of M12 L-encoding (socket); port X04 (OUT)
Co ectio for I puts/Outputs X1 ... X8
•Connection: M12 socket, 5 pin, A-coded
•Color coding: black
Figure 2.5 Schematic drawing of M12 socket, 5-pin, A-encoded, port X1 ... X8
Modules ICE1-8DI8DO-G60L-V1D a d ICE1-8DI8DO-G60L-C1-V1D
Port Pi Sig al Fu ctio
Power supply
X03, X04
1 U
S
(+24 V) Sensor/system supply
2 GND U
L
Ground/reference potential V
Aux
3 GND U
S
Ground/reference potential V
s
4 U
L
(+24 V) Auxiliary power supply (galv. insulated)
FE (5) FE (FE) Functional ground
4
1
3
2
FE
Note
For the system/sensor and actuator supply, use only power supplies that comply with PELV
(protective extra-low voltage) or SELV (safety extra-low voltage). Power supplies according to
EN 61558-2-6 (transformer) or EN 60950-1 (switching power supplies) fulfill these
requirements.
1
5
3
2
4
Note
Depending on the module type, the pins of ports X1 ... X8 are occupied differently.
Note
For inductive loads of usage category DC13 (EN60947-5-1), the outputs are able to control
currents of 1.6 A at a frequency of 1 Hz.
Port Pi Sig al Fu ctio
nputs
X1 ... X4
1 +24 VDC Sensor/system supply
2 N B Digital input B
3 0 VDC Ground/reference potential
4 N A Digital input A
5 FE (FE) Functional ground

2019-10
14
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Product Description
Module ICE1-16DI-G60L-V1D
Modules ICE1-16DIO-G60L-V1D a d ICE1-16DIO-G60L-C1-V1D
2.4 Dime sio s
Figure 2.6 CE1-8D 8DO-G60L-V1D
CE1-8D 8DO-G60L-C1-V1D
CE1-16D -G60L-V1D
CE1-16D O-G60L-V1D
CE1-16D O-G60L-C1-V1D
Port Pi Sig al Fu ctio
Outputs
X5 ... X8
1 Not used
2 OUT B Digital output B
3 0 VDC Ground/reference potential
4 OUT A Digital output A
FE (5) FE (FE) Functional ground
Port Pi Sig al Fu ctio
nputs
X1 ... X8
1 +24 VDC Sensor/system supply
2 n B Digital input B
3 0 VDC Ground/reference potential
4 n A Digital input A
FE (5) FE (FE) Functional ground
Port Pi Sig al Fu ctio
Outputs
X1 ... X8
1 +24 VDC Sensor/system supply
2 N B/OUT B Can be configured as digital input B or
output B
3 0 VDC Ground/reference potential
4 N A/OUT A Can be configured as digital input A or
output A
FE (5) FE (FE) Functional ground
17.6
30.7
214.5
20
30
59.6
27 27 27 M12 x1 (10x) 27 11.5
16.5
190.3
191.8
200
M4

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
nstallation
2019-10
15
3 I stallatio
3.1 Ge eral I formatio
nstall the module with two M6x25/30 size screws on a level surface. The required torque is
1 Nm. Use washers according to D N 125. For the installation holes, use a spacing of
237.3 mm to 239.7 mm.
Note
Power supply connection
When connecting the power supply, ensure a separate power supply to the sensor and system
via U
s
and auxiliary supply via U
L
for e.g., actuators. Where the plant has a separate power
supply concept for system current and load current, this means the sensor and system area of
the Ethernet O module can continue working even if there is a failure of the load power supply.
Where several Ethernet O modules are connected in series, ensure the separate power
supplies are connected properly U
s
.U
L
.
Note
To dissipate interference currents and the EMC strength, the modules use a short circuit to
ground with an M4 thread. This is marked with the symbol for grounding and the label "XE.”
Note
Connect the module using a low-impedance connection with the reference ground. n the case
of a grounded mounting surface, you can connect the module directly via the fixing screws.
Note
For non-grounded mounting surfaces, use a ground strap or a suitable FE conductor. Connect
the ground strap or FE conductor to the grounding point using an M4 screw and place a washer
and a serrated washer under the fixing screw if possible.
Note
To program the controller, please consult the manufacturer information and use only the
appropriate accessories.
Note
For UL application:
Only connect Ethernet O modules using a UL-certified cable with suitable ratings (CYJV or
PVVA).
Approved only for indoor use. Please observe the maximum altitude of 2000 meters. Approved
up to a maximum of pollution degree 2.
War i g!
Terminals, the housing of field-wired terminal boxes or components may exceed a temperature
of 60 °C.

2019-10
16
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
nstallation
War i g!
Use temperature-resistant cable with heat resistance up to at least 96 °C for the following
Ethernet O modules:
CE1-8D 8DO-G60L-C1-V1D and CE1-8D 8DO-G60L-V1D
CE1-16D O-G60L-V1D and CE1-16D O-G60L-C1-V1D

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Commissioning, Protocol Setting
2019-10
17
4 Commissio i g, Protocol Setti g
4.1 Setti g Protocols
Multiprotocol
You can use the multiprotocol modules to select various protocols for communication within a
fieldbus system. This allows you to integrate the multiprotocol modules into different networks
without having to obtain a specific module for each protocol. This technology also allows you to
use the same module in different environments. Using the rotary switches on the front of the
modules, you can easily and conveniently set the protocol and address of the module if the pro-
tocol to be used supports this. Once you have selected a protocol and started the cyclical com-
munication, the module recognizes these settings and uses the selected protocol from this
point on. To use another supported protocol with this module, perform a factory reset.
Setti g a Protocol
Multiprotocol modules have a total of three rotary switches. Alter the switch position for the first
rotary switch X100 to set the protocol. For the other rotary switches, set the last two digits of the
P address when using EtherNet/ P.
Figure 4.1 Rotary switch X100
Assig i g the Protocol Usi g the Rotary Switches
The default settings of the module do not contain any protocol settings. n this case, simply
select the desired protocol. To use a modified rotary switch setting (protocol setting), you have
to execute a power cycle or "Reset" of the web interface. Once you have set the protocol using
the rotary switches, the module saves these settings as soon as it starts a cyclical communica-
tion. From this point, you can no longer change the protocol using the rotary switch. To change
the protocol, perform a factory reset first.
f you set the rotary coding switch to an invalid position, the device signals this with a flash
code: the BF/MS/ERR LED flashes red three times.
You can change the P address depending on the selected protocol.
Protocol X100 X10 X1
EtherNet/ P 0-2 0-9 0-9
PROF NET P - -
EtherCAT EC - -
20X10X
X03
X4 X8
7X3X
X6
5
X1
X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
X02
X01
US
16DI
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
P
00
9
EC
RUN ERR
FM
C
R
0E/IP
P
EC
X100
9

2019-10
18
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Commissioning, Protocol Setting
EtherNet/IP
f you use EtherNet/ P as the protocol, use rotary switch X100 to set the value 100 as the last
octet of the P address for the module. With the X100 rotary switch, you can set a value of 0 to 2
for the P address. With the X10 and X1 rotary switches, you can set values between 0 and 9.
You can use rotary switch X10 to configure position 10 of the last octet of the P address. With
rotary switch X1 you can configure position 1 of the last octet of the P address.
The default setting for the first three octets of the P address is 192.168.1.
Example: Rotary switch settings 2 (X100), 1 (X10), and 0 (X1) result in an P address of
192.168.1.210 for EtherNet/ P.
Alternatively, the required network parameters can be obtained via DHCP or BOOTP if the
rotary switch is set to zero.
PROFINET
f you use PROF NET as the protocol, set rotary switch X100 to the value "P.”
EtherCAT
f you are using EtherCAT as the protocol, set rotary switch X100 to the value "EC.”
Factory Setti gs
A factory reset erases any changes you have made to settings etc. and restores the factory set-
tings. The saved protocol selection is also reset.
To perform a factory reset, set rotary switch X100 to 9, rotary switch X10 to 7 and rotary switch
X1 to 9. Then switch the module off and on again. The factory settings are restored after 10
seconds.
To select a new protocol, follow the instructions in this chapter.
Figure 4.2 Restoring factory settings: X100 = 9, X10 = 7, X1 = 9
20X10X
X03
X4 X8
7X3X
X6
5
X1X
X2
A
DIA
B
XE
X04
BF DIA
Lnk/Act
X02
X01
US
16DI
A
DIA
B
A
DIA
B
A
DIA
B
x100 x10 x1
MS NS
0E/IP
P
00
9
EC
RUN ERR
FM
CX10
0
X1
0
X100
0E/IP
P
EC
9
Cautio !
Destruction of the Operating System
When restoring the factory settings, ensure that the module is connected to the power supply
and switched on for at least 10 seconds. f it has been on for less than 10 seconds, the operat-
ing system may be destroyed. The module then has to be sent to Pepperl+Fuchs for repair.

CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Commissioning for EtherNet/ P
2019-10
19
5 Commissio i g for EtherNet/IP
5.1 Preparatio
To configure a module in the controller, you need an EDS file. Each of the module variants
requires its own EDS file.
Dow loadi g the EDS File
You can find the relevant EDS file in the Software section of the product detail page for the
device.
To access the product detail page for the device, go to http://www.pepperl-fuchs.com and type
information about the device, e.g., the product description or the item number, into the search
function.
Use the hardware or network configuration tools from your controller manufacturer to install the
EDS file for the module variant used. After installation, the modules can be found in the hard-
ware catalog as "General Purpose Discrete /O" devices.
Readi g MAC IDs
Each module has a unique, manufacturer-assigned MAC D that cannot be changed by the
user. The assigned MAC D is printed on the right-hand side of the module.
Setti g the Network Parameters
Using the three control switches on the front of the modules, you can set the operating mode
for receiving network parameters such as the P address, subnet mask, and gateway address.
Please note that a fixed P address is required to use QuickConnect.
Once the power supply has been restored, the modules read in the switch positions. The
selected operating mode overwrites the saved settings.
The devices support the DHCP and BOOTP protocols for receiving the required network
parameters such as P address and subnet mask.
The factory settings of the static network parameters are:
•P address: 192.168.001.001
•Subnet mask: 255.255.255.000
•Gateway address: 000.000.000.000
The following settings are possible via the rotary coding switches:
Rotary switch posi-
tio Fu ctio
000
(As delivered)
The DHCP and BOOTP functionality is activated as standard on deliv-
ery. The network parameters are initially requested using DHCP
requests. f this is not successful, the request is made using BOOTP
requests. The network parameters are not saved; however, it is possi-
ble to save them via the integrated web server.
000
(Network parameters
already saved)
The last-saved network parameters are used ( P address, subnet
mask, gateway address, DHCP on/off , BOOTP on/off).
001 to 254 The last three digits of the saved or default P address are overwritten
by the control switch setting.
255 to 298
(Default: 299)
The network parameters are requested via DHCP and BOOTP but are
not saved.

2019-10
20
CE1-*-G60L-V1D, CE1-*-G60L-C1-V1D
Commissioning for EtherNet/ P
5.2 Co figuratio
Implicit a d Explicit Messagi g
The Ethernet O modules support implicit and explicit messaging for EtherNet/ P communica-
tion. O process data is transmitted on a cyclical basis via assembly objects and an existing
connection using implicit messaging.
Low-priority data, non-time-critical data, configuration and diagnostic data can be exchanged
via non-cyclical messages using explicit messaging.
Co ectio s a d Assembly Object
The Ethernet O modules support connection types Exclusive Owner, nput Only and Listen
Only for exchanging O process data and communication via implicit messaging.
•Exclusive ow er
This connection is bidirectional: the controller sends data to the module and the module
sends data to the controller. This type of connection is known as exclusive owner because
it connects o e module to the controller in each case.
•I put o ly
With this type of connection, only the module sends data to the controller. The module
sends a heartbeat, possibly at reduced intervals. This enables the controller to detect
interruptions to the connection.
•Liste o ly
This connection corresponds to the input only connection but can only be established if
an exclusive owner or input only connection also exists between another module and the
controller.
An “exclusive owner” connection is only available for modules with output functionality (variants
16D O and 8D 8DO). By selecting the corresponding instance D for the assembly object, you
determine whether the module adds diagnostic data to the standard process data.
The 16D O-variant Ethernet modules are universally applicable and provide a variety of profiles
for basic configuration. Using these, you can preconfigure a 16D O module as a 16D , 16DO or
8D /8DO module, among other things, and replace a module where required, for example.
Each /O channel can be used as an input or output for the 16D /DO profile. f an /O channel is
used as an input, the PLC programmer should not set the corresponding output bit.
By using the preconfigured alternate profiles, the risk of incorrect configuration is reduced
through the use of profiles 16D , 16DO or 8D /8DO. n these profiles, the /O channels are con-
figured as "input" or "output."
Ethernet O modules of type CE1-8D 8DO-G60L-C1-V1D CE1-16D O-G60L-C1-V1D have
the DCU function. For these, the process data is extended in both directions by 18 additional
bytes.
979 The device performs a reset to factory settings. The network parame-
ters are also reset to the default values. Communication is not possi-
ble in this operating mode.
Table 5.1
Rotary switch posi-
tio Fu ctio