Pepperl+Fuchs RocketLinx ICRL-U-5RJ45-G-DIN User manual

Quick Installation Guide
DOCT-6559 | Release Date- February 2020
ROCKETLINX
ICRL-U-5RJ45-G-DIN
ICRL-U-4RJ45/SFP-G-DIN
Electronic.indd 1 12/4/2019 9:16:57 AM

Introduction
ICRL-U-5RJ45-G-DIN and ICRL-U-4RJ45/SFP-G-DIN are a compact
size Ethernet unmanaged Gigabit switches, which ensure high
switching performance and easy installation. Along with its high
switching performance, it supports multiple internal performance
features, such as 9K bytes Jumbo Frame, Flow Control, and it ensures
quality trac transmission.
The ICRL-U-5RJ45-G-DIN provides five 10/100/1000T(X) RJ45 ports.
The ICRL-U-4RJ45/SFP-G-DIN provides four 10/100/1000T(X) RJ45
ports and one 1000BASE-F(X) SPF port.
The switch provides a rugged metal case design (IP31) to operate in
harsh environments (-40 to 75°C).
It features one relay output to alarm users if power fails.
Wiring the Power Inputs
The switch provide power redundancy and polarity reverse protection.
Use a UL Listed power supply with a recommended working voltage of
24VDC with an input range of 10-60VDC.
PWR1 and PWR2 are dual power inputs that can be connected to
power sources simultaneously. When the primary power source fails
(PWR1), the system automatically switches to the secondary power
source (PWR2), preventing any power interruption.
Both of PWR1 and PWR2 support positive electricity and negative
electricity power systems. Please notice the power system for PWR1
and PWR2 only accept either positive or negative electricity power
system at one time
2
Electronic.indd 2 12/4/2019 9:16:57 AM

1. Insert the positive and negative wires into the V+ and V- contact
on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires
loosened.
Wiring the Relay Output (DO)
The relay output contacts are in the middle of the terminal block
connector as shown below. Insert the wires as show below to connect
the relay output alarm so that it detects power fault and avoids
forming a short-circuit.
Note: The relay contact only support 1A current, 24VDC.
Pepperl+Fuchs does not recommend apply higher voltage and current
that over this specification.
3
Electronic.indd 3 12/4/2019 9:16:57 AM

Connecting to Network
Connect one end of an RJ45 Ethernet cable into the UTP port of
switch, while the other end is connected to the attached networking
device. The UTP port supports the auto MDI/MDIX function.
Ethernet cables are categorized into unshielded twisted-pair (UTP)
and shielded twisted-pair (STP) cables. Category 3, 4, 5 Ethernet
cables are suitable for systems with 10 Mbps transmission speed.
For systems with 100/1000 Mbps transmission speed, Category 5e or
Category 6 Ethernet cables are the only suitable specifications for this
environment. Also make sure that the distance between each node
cannot be longer than 100 meters (328 feet).
The ICRL-U-4RJ45/SFP-G-DIN SFP port
supports hot-swapping and you can change
the SFP fiber transceiver without system
power o. This feature is useful for field
site installations if the fiber signal cannot
attach the other end device - just change
to a dierent SFP transceiver type with
larger power launch power budget. The SFP port accepts a standard
Gigabit MINI GBIC SFP transceiver. Plug in the SFP transceiver and
cross-connect the transmit channel at each end to receive channel at
the opposite end.
4
Electronic.indd 4 12/4/2019 9:16:57 AM

ATTENTION This is a Class 1 Laser/LED product. Do not look
into the Laser/LED beam.
LEDs
The LNK / ACT LED turns on for link up and blinks for packet transmit
and receive. The Speed LED turns on for Gigabit link and turns o for
10/100Mbps link.
LED Color Function
P1, P2 Green Power (1,2) on
P-F Red Power failure (1 or 2)
1-5
(ICRL-U-5RJ45-G-DIN)
1-4
(ICRL-U-4RJ45/SFP-G-DIN)
Green Link
Flashes Green Activity
Amber Gigabit speed
SFP
(ICRL-U-4RJ45/SFP-G-DIN)
Green Link
Flashes Green Activity
Grounding the Switch
There is one grounding screw on the bottom side of switch. Connect
the earth ground screw of the switch to the grounding surface to
ensure safety and prevent noise.
5
Electronic.indd 5 12/4/2019 9:16:57 AM

Mounting the Switch
You can mount the switch on a DIN rail. The
DIN rail clip is attached to the switch, which
supports the EN 50022 DIN Rail standard.
1. Insert the upper end of DIN rail clip into
the back of DIN rail track from its upper
side.
2. Lightly push the bottom of DIN rail clip
into the track.
3. Verify that the DIN rail clip is tightly
attached on the track.
6
Electronic.indd 6 12/4/2019 9:16:57 AM

Customer Service
You can use one of the following methods to contact Pepperl+Fuchs.
Worldwide Headquarters
Pepperl+Fuchs AG
68307 Mannheim, Germany
[phone]
[email protected]
USA Headquarters
Pepperl+Fuchs, Inc.
Twinsburg, Ohio 44087 - USA
[phone]
[email protected]
Asia Pacific Headquarters
Pepperl+Fuchs Pte Ltd.
Company Registration No.199003130E
Singapore 139942
[phone]
[email protected]
7
Electronic.indd 7 12/4/2019 9:16:57 AM