PERFECTPRO Rock Bull User manual

GB
E
NL
GBINSTRUCTION MANUAL
MODE D’EMPLOI
BENUTZERHANDBUCH
HANDLEIDING
F
D
NL

CONTENTS
1. CONTENTS………....................……………………………………………………… 1
2. IMPORTANT GENERAL SAFETY INSTRUCTIONS……............……………. 2
3. CONTROLS…………………………………………………….............…………... 3
4. POWER SUPPLY………………………………………….............……………… 4
5. GENERAL FUNCTIONS………………………………..............………………… 4
6. USING THE RADIO FOR THE FIRST TIME…………...............……………….. 5
7. DAB MODE………………………………………………...............……………….. 5
8. FM MODE…………………………………………………..............………………. 8
9. PRESET STATIONS……………………………………................………………... 9
10. AUX-IN MODE……………………………………………................………………. 10
11. MANUALLY SETTING CLOCK……………………….............…………………. 11
12. VOLUME & SOUND……………………………….............……………………… 11
13. LOUDNESS………………………………………….............…………………….. 12
14. SURROUND SOUND……………………………...............………………………. 12
15. EQUALIZER…………………………………………................…………………….. 12
16. ADDITIONAL METAL TELESCOPIC ANTENNA……….....……………… 13
17. LANGUAGE SETTING……………………………………................……………… 13
18. SOFTWARE VERSION………………………………………...............…………... 14
19. SYSTEM RESET………………………………………................………………….. 14
20. BACKLIGHT…………………………………………...............…………………….. 14
21. ATP PASSCODE……………………………………...................…………………….. 15
22. WARRANTY………………………………………….................…………………….. 15
23. INFORMATION…………………………...............…………………………………. 16
WARNING ! WARRANTY BECOMES VOID ONCE THE DEVICE CABINET HAS BEEN
OPENED OR ANY MODIFICATIONS OR ALTERATIONS TO THE ORIGINAL DEVICE
HAVE BEEN MADE
1 2
GB
GB
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves or
 otherapparatus(includingampliers)thatproduceheat.
8. Do not defect the safety purpose of the polarized or grounding – type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third prong
 isprovidedforyoursafety.Iftheprovidedplugdoesnottintoyouroutlet,consult
an electrician for replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched particularly at plug,
convenience receptacles, and the point where they exit from the apparatus.
10. Onlyuseattachments/accessoriesspeciedbythemanufacturer.
11. Useonlywiththecart,stand,tripod,bracket,ortablespeciedbythemanufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of
time.
13. Referallservicingtoqualiedservicepersonnel.Servicingisrequiredifthe
apparatus has been damaged in any, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
14. Toreducetheriskofreorelectricshock,donotexposethisappliancetorainor
moisture.
15. Do not remove the cover; there are no user-serviceable parts inside.
16. Nonakedamesourcesshallbeplacedontheapparatus.
17. For outdoors use, to avoid electric shock, if the radio has been exposed to rain or
water, the power supply cord and plug must be completely dried before plugging
into the mains socket outlet.
18. The power plug should be close to the apparatus, and easy to be approached that
during emergency, to disconnect the power from the apparatus, just unplug the
power plug from the AC power slot.
19. The marking information is located at the bottom of the apparatus.
20. Thisapparatusisprovidedwithprotectionagainstsplashingwater(IPX4).
21. Incaseofmalfunctionduetoelectrostaticdischargeorfasttransient(burst),
remove and reconnect the power supply.

CONTROLS
1. Aux-in
2. Volume
3. Display
4. Key pad
5. Tuning
6. Antenna
7. Power cord
3 4
GB
GB
1 2 543
6 7
POWER SUPPLY
AC operation
1. Before plugging the AC power cord into the AC socket, be sure the voltage is
correct.
2. AC power cord and plug storage is designed to store the cord and plug when the
radio is not in use
Note:
In order to disconnect the unit from the AC mains completely, the AC power cord should
be removed from the mains socket completely and it shall remain readily operable and
should not be obstructed during intended use.
Incaseofmalfunctionduetoelectrostaticdischargeorfasttransient(burst),removethe
power supply from power supply and reconnect the power supply after half approximate
minute.
GENERAL FUNCTIONS
1. Switching on and off
Press the On/Off button to turn the radio on or in standby.
2. Switching among DAB / FM / AUX-IN modes
Press the SOURCE button to switch between modes.
3. Tuning the Radio
Tune the radio using the TUNING knob on the right.
4. Adjusting the Volume
Adjust the volume with the VOLUME knob on the left.
5. Selecting the preset Equalizer
Press the EQUALIZER button repeatedly to select the desired preset EQ.
6. Selecting Stereo or Mono mode (in FM mode only)
Press the MONO/STEREO button to switch between FM Mono and FM Stereo.
7. Using the AUX-IN feature
Connect the audio output of an external audio device to the Ø3.5mm AUX-IN socket
and play music from the external device.
8. Anti-Theft-Protection (ATP) System
 Pressthepresetbuttons(1-10)toenterthe4-digitsnumericpasscode.

5 6
GB
GB
USING THE RADIO FOR THE FIRST TIME
1. Placetheradioonaatsurface.
2. Carefully extend the antenna located on the top of the radio. Adjust the antenna so
it is vertically extending above the radio.
3. Plug the AC power cord into the AC socket. The radio will start up and the display
will show “Welcome To Digital Radio” for a few seconds. Then the radio will
automatically perform an auto scan of the Band III DAB channels and the FM band.
The display will show “Scanning” in DAB and “Auto” in FM.
4. When the scan is completed, the 10 strongest stations of DAB and FM will be
stored as presets. The radio will switch to standby with the updated clock and date
showing on the display.
5. If no signals are found, the clock will not be updated. It may be necessary to
relocate the radio to a position with better reception.
DAB MODE (DAB – DAB+)
Operating the radio – DAB
1. Carefully extend the antenna. Press the On/Off button to switch on the radio.
2. Select DAB by pressing the SOURCE button.
3. Therststationinthelistofstationsfoundwillbeplayed.Thedisplaywillshow
the station name. If the radio has been used before, the last used station will be
selected.
4. If no DAB signals are detected, “No stations available” will be displayed. It may
be necessary to relocate the radio to a position with better reception. You should
 thencarryoutanautoscantondstations,pleaserefertothesection“Find new
stations - DAB”.
Selecting a station – DAB
1. Press the On/Off button to switch on the radio. The display will show “Connecting”
and “Playing” for a few seconds.
2. The display shows the name of the radio station currently selected.
3. Rotate the TUNING knob to scroll through the list of available stations.
4. When the desired station name appears on the display, press the TUNING knob to
select the station.
Note: If after selecting a station the display shows “No stations available”, it may be
necessary to relocate the radio to a position with better reception.
Display modes – DAB
In DAB mode, the radio can display a range of information on the display.
Press the INFO button to cycle through the various modes.
a. Scrolling text Displays scrolling text message e.g. station information,
artist/track name, phone-in number, etc.
b. Signal strength Displays the signal strength of radio reception. The
  clearunlledrectangleindicatesminimumsignallevel
required for satisfactory reception.
c. Program type Displays the type of station being listened to e.g. Pop,
Classic, News, etc.
d. Multiplex name Displays the name of multiplex to which the current
station belongs.
e. Channel & frequency Displays the channel number and frequency for the
currently tuned DAB station.
f. Bit rate & audio format Displays the digital audio bit rate and audio format.
g. Time & date Displays the current time and date.
Finding new stations – DAB
Fromtimetotime,newstationsmaybecomeavailable.Youmayproceedtondnew
stations as follows:
1. In DAB mode, press the MENU button, “Full Scan” shows on the display.
2. Press the TUNING knob, the radio will perform a scan of the Band III DAB
channels. As new stations are found, the station counter on the right-hand side of
the display will increase and new radio stations found will be added to the list stored
in the radio.
Manual Tuning – DAB
Manualtuningisanalternativemethodofndingnewstations.Insteadofscanningthe
entire Band III channels automatically, you may tune the radio directly to a known DAB
channel and store all the multiplex in that channel into the available station list.
1. In DAB mode, press the MENU button and rotate the TUNING knob until the LCD
display shows “Manual tune”, then press the TUNING knob. The display will show
DAB channel and Frequency.
2. Rotate the TUNING knob to select the desired Channel or Frequency and then
press the TUNING knob to tune to the chosen frequency.
3. When DAB stations in the tuned channel are found, the display will show the name
of the station. Any new radio stations found will be added to the list stored in the radio.
4. Thesignalstrengthdisplayshowsthereceptionofthestation.Theclearunlled
rectangle indicates minimum signal level required for satisfactory reception. The
signal strength bars will go up or down showing the changing signal strength as you
adjust the antenna or the radio position.

7 8
GB
GB
5. Repeat step 1 to 4 for other channels with new stations.
6. Press the MENU button twice to exit manual tuning and return to normal DAB
operation.
Dynamic Range Control (DRC) settings – DAB
DRC can make quieter sounds easier to hear when your radio is used in a noisy
environment.
1. In DAB mode, press the MENU button and rotate the TUNING knob until the display
shows “DRC Value”, then press the TUNING knob.
2. Rotate the TUNINGknobtoselectrequiredDRCsetting(defaultisOFF).
DRC off DRC is switched off, broadcast DRC will be ignored.
DRC high DRC is set as sent by broadcaster.
DRC low DRC level is set to 1/2 that sent by broadcaster.
3. Press the TUNINGknobtoconrmthesetting.Thedisplaywillreturntonormal
radio display.
Note: Not all DAB broadcasts are able to use the DRC function. If the broadcast does
not support DRC, then the DRC setting in the radio will have no effect.
Prune stations – DAB
If you move to a different part of the country, some of the stations that were listed
may no longer be available. Also, from time to time, some DAB services may stop
broadcasting, or may change location or frequency. The Prune stations function will
delete the unavailable DAB stations from your station list.
1. In DAB mode, press the MENU button.
2. Rotate the TUNING knob until the display shows “Prune”.
3. Press the TUNING knob to enter the setting.
4. Rotate the TUNINGknobtoselectbetween“Yes”or“No”(defaultisNo).Select“Yes”
to enable this function if required, otherwise, select “No”.
5. Press the TUNINGknobtoconrmyoursetting.Thedisplaywillreturntolastmenu
and press MENU to go to the normal radio display.
Note: If you have moved the radio to a different part of the country, you should also carry
out a search for new stations (please see the section “Finding new stations – DAB”).
FM MODE
Operating the radio – FM seek station
1. Press the On/Off button to switch on the radio.
2. Select the FM RADIO waveband by pressing the SOURCE button.
3. IfthisisthersttimetoswitchtoFMmode,thestationinpreset1willbeplayed.If
the radio has been used before, the last listened station will be played.
4. To seek station, press the TUNINGknob.Thescanstopsautomaticallywhenitnds
 astationofsufcientstrength.
5. After a few seconds, the display will update and show station name if RDS
information is being received.
6. Tondotherstations,presstheTUNING knob again.
7. To seek station in an opposite direction, rotate the TUNING knob clockwise (to scan
 fromlowfrequencytohighfrequency)orrotatetheTUNING knob anti-clockwise (to
 scanfromhighfrequencytolowfrequency),andpresstheTUNING knob.
8. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.
Manual tuning – FM
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Rotate the TUNING knob to reach the required FM station. The radio will change
the frequency in steps of 50 kHz.
4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a station
 ofsufcientsignalstrengthwithRDSinformationpresent,thedisplaymaychange
to show the station name.
5. When the waveband end is reached, the radio will recommence tuning from the
opposite waveband end.
RDS station service – FM
RDS(RadioDataSystem)isaninformationsystemwhichinaudibledigitalinformation
is transmitted in addition to the normal FM radio program. When the radio is receiving a
RDSstationandthereceptionstrengthissufcient,thestationnamewillappearinthe
display. It may take some time before the RDS information is available.

9 10
GB
GB
Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the INFO
button to cycle through the information. This will only function if the reception level is
sufcientandclear.
a. Stationname(PS) Displaysthenameofstationbeinglistenedto.
b. Radiotext(RT) Displaysthemessageaboutthestationbeinglistenedtoas
ticker text.
c. Programtype(PTY) Displaysthetypeofstationbeinglistenedto,e.g.Pop,
Classic, News, etc.
d. Frequency Displays the frequency of the station being listened to.
e. Stereo or Mono Displays Stereo or Mono.
f. Signal level Displays the signal strength.
g. Time&date Displaysthecurrenttime(24hourclock)anddate.
Scan sensitivity setting – FM
The radio will normally scan all stations from FM broadcasts including the weaker
signals.However,youmaywishtheAuto-scantondonlythosestationswithstrong
enough signals to give good reception.
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the MENU button, the display shows “Scan Setting”.
4. Press the TUNING button.
5. Rotate the TUNING knob to select “All Stations” or “Strong Station” (default is “All
 Stations”).The“StrongStation”optionwillallowtheradiotondstrongsignalsonly
when scanning.
6. PresstheTUNINGknobtoconrmyoursetting.Thedisplaywillreturntonormal
radio display.
FM stereo / mono
1. If the FM station being received is weak, some hiss may be audible. To reduce
the hiss, press the Mono/Stereo button to switch to mono mode, the display will
show “Mono”.
2. To return to stereo mode, press the Mono/Stereo button and the display shows
“Stereo”, the radio will switch to stereo mode automatically if the reception is good.
3. “Mono” and “Stereo” can be displayed on the LCD display (See “Calling up RDS
information”above)
PRESET STATIONS
Storing preset stations
There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are
remembered by the radio in the event of a power failure.
1. Press the On/Off button to switch on the radio.
2. Select the desired waveband by pressing the SOURCE button.
3. Tune to the required station.
4. Press and hold the required Preset(1–10)buttonuntiltheradiobeepsandshows
“Saved”.
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written again by following the
above procedures.
Recalling preset stations
1. Press the On/Off button to switch on the radio.
2. Select the desired waveband by pressing the SOURCE button.
3. BrieyPresstherequiredPreset(1-10)button.InFMmodethedisplaywillshow
for example ”P1” on top right hand side.
AUX-IN MODE
A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (Aux cable not
includedwiththisradio).
1. Connect an audio source to the AUX-IN socket.
2. Press the SOURCE button to select AUX input. Display will show “AUX IN”.
3. Play the external player.
4. Adjust the VOLUME of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover well closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal* from the Aux-In socket for a period of over 15 minutes, the radio will automatically
switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.

11 12
GB
GB
MANUALLY SETTING CLOCK
The clock can only be set when the radio is in standby mode. If no buttons are pressed
for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the TIME SETknobfor12secondsuntilthehourdigitsashonthe
display.
2. Rotate the TIME SET knob to set the hour.
3. Press the TIME SETknobtoconrm,theminutedigitsash.
4. Rotate the TIME SET knob to set the minute.
5. Press the TIME SETknobtoconrm.Thedayashes.
6. Rotate the TIME SET knob to set the current day.
7. Press the TIME SETknobtoconrm.Themonthashes.
8. Rotate the TIME SET knob to set the current month.
9. Press the TIME SETknobtoconrm.Theyearashes.
10. Rotate the TIME SET knob to set the current year.
11. Press the TIME SETknobtoconrm.“Synclockon”ashes.
12. Rotary the TIME SET knob to choose either “Synclock on” or “Synclock off”.
13. Press the TIME SETknobtoconrmandnishtheclocksetting.
Automatic time synchronization
If “Synclock on” option is selected, the clock can be automatically set and updated every
time the radio is switched on. The clock will be synchronized to the DAB or FM radio
station received during the last radio operation.
Iftheclockisstoppedorresetduetopowerinterruption(oraftera“SystemReset”),
the clock will be automatically set again and updated to the DAB or FM radio station
received during the last radio operation. This will be done no matter the “Synclock”
option is set to on or off.
Auto time set or time synchronization can take few minutes, which depends on the
signal strength of the radio station. If it is not successful after 10 to15 minutes, it may be
necessary to relocate the radio to a position with better radio reception.
VOLUME & SOUND
To adjust the volume, simply rotate the VOLUME knob when the radio is on. The volume
level(from00to40theloudest)willbeshownontheLCDDisplay.
2-Way Speakers
The ROCKBULL radio has built-in 2-way speakers for each channel. The woofer in each
channel reproduces the lower frequencies and the tweeter in each channel reproduces
the high frequencies. 2-way speakers can reproduce dynamic and powerful sound while
maintains high clarity and accurate sound image.
LOUDNESS
The Loudness function enables to get compensation on lower and higher frequency.
The effect will be more audible when the radio is on a lower volume level (Dynamic
Loudness).
1. Press the On/Off button to switch on the radio.
2. Press the LOUNDNESS button alternatively, and then select between “Loudness
on” or “Loudness off”.
3. The display will return to normal in 3 seconds, and resume operation.
SURROUND SOUND
The ROCKBULL radio uses a digital signal processor to adjust the original audio signal
to reproduce a digital virtual Surround sound. The sound reproduction quality is highly
enrichedofferingyouaspaciousandperspectivesoundeld.
1. Press the On/Off button to switch on the radio.
2. Press the SOURCE button to select DAB or AUX-IN mode.
3. Press the SURROUND button alternatively, and then select between “Surround on”
or “Surround off”.
4. The display will return to normal in 3 seconds, and resume operation.
The Surround Sound effect varies strongly per music type. Mostly the best result will be
obtained with “lighter and easy listening” music. “Loud and heavy” music will often result
inaless“opensound”orevendistortion.Allthisisofcoursestronglyinuencedbythe
volume level and selected equalizer setting.
TheSurroundSoundeffectisbestusedinalargerroomwithreectingwallsand
listening at a few metres away from the radio. Very close to the radio the Surround
Sound effect is not optimal.
Note: The Surround Sound is not available in FM mode.
EQUALIZER
The EQUALIZER function enables you to select a setting from 12 presets. Each presets
EQ contains a group of parametric controls in the digital audio processor, which offer
you optimum adjustments for various kinds of music and applications for different
environments.
1. Press the On/Off button to switch on the radio.

13 14
GB
GB
2. Press the EQUALIZER button repeatedly to select the desired EQ. The displayed
EQ will be effective immediately:
EQ1 Neutral
EQ2 Indoor
EQ3 Outdoor
EQ4 Flat
EQ5 Rock
EQ6 Soul and Jazz
EQ7 Classical
EQ8 Acoustic
EQ9 Dance
EQ10 Spoken word
EQ11 Small room
EQ12 Late night
3. The display will return to normal in 3 seconds, and resume operation.
ADDITIONAL METAL TELESCOPIC ANTENNA
You can use this as an alternative antenna for your radio in areas or locations where the
radiosignal(FM/DAB/DAB+)isweaktoveryweak.
ATTENTION: The standard antenna on the radio is exible. The metal antenna
is not exible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing:Carefullyscrewoffthestandardexibleantenna.Firstcarefullyloosenthe
antennawithanopen-end-wrench(size14)–turncounteranti-clockwise.
Carefully screw on the metal telescopic antenna and softly tighten it with an open-end
wrenchkey(size14)–turnclockwise.
ATTENTION: do not use too much force when xing the antennas as this can
damage the screw threat of the antennas or make it break off.
LANGUAGE SETTING
Themenuoftheradiocanbeconguredtovariouslanguages.
1. Press the On/Off button to switch on the radio.
2. Press the MENU button, and then rotate the TUNING knob until the display shows
“System”.
3. Press the TUNING knob; rotate the TUNING knob until the display shows
“Language”.
4. Press the TUNING knob b to enter the language adjustment menu.
5. Rotate the TUNING knob until the desired language appears on the display (default
 isEnglish).
6. Press the TUNINGknobtoconrmyourchoice.
7. The display menu will then change to the chosen language.
SOFTWARE VERSION
The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM modes.
1. Press the On/Off button to switch on the radio.
2. Press the SOURCE button to select FM or DAB mode.
3. Press the MENU button and then rotate the TUNING knob until the display shows
“System”.
4. Press the TUNING knob; rotate the TUNING knob until the display shows “SW
version”.
5. Press the TUNING knob to view the software version.
6. Press the MENU button to return to the normal radio display.
SYSTEM RESET
If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the On/Off button to switch on the radio.
2. Press the MENU button.
3. Rotate the TUNING knob until the display shows “System”. Press the TUNING
knob.
4. Rotate the TUNING knob until the display shows “Factory Reset”. Press the
TUNING knob.
5. Rotate the TUNING knob to select between “Yes” or “No”. Select “Yes” if you wish to
reset the radio, otherwise, select “No”.
6. Press the TUNINGknobtoconrmyourchoice.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values. The radio will start up and the display
will show “WELCOME TO DIGITAL RADIO” for a few seconds. Then the radio will
automatically perform an auto scan of the Band III DAB channels and the FM band.
The display will show “Scanning” in DAB and “Auto” in FM.
8. When the scan is completed, the 10 strongest FM stations will be stored as presets.
The radio will switch to standby with the updated clock and date showing on the
display.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
reconnect the power supply.
BACKLIGHT
When the radio is in operation or in standby, pressing any button will illuminate the LCD
display for approx. 10 seconds.

15 16
ATP PASSCODE
ThisradioisequippedwithanAnti-Theft-Protection(ATP)system.WhentheATP
system is enabled, a passcode is required for turning on the radio.
1. Press the On/Off button to turn on the radio.
2. Press the MENU button.
3. Rotate the TUNING knob until the display shows “System”. Press the TUNING
knob.
4. Rotate the TUNING knob until the display shows “Passcode”. Press the TUNING
knob; “Enable” or “Disable” will be displayed. To enable ATP, rotate and press the
TUNING knob to select “Enable”.
5. “Change passcode” will be displayed, enter a 4-digits numeric passcode by pressing
 thepresetbuttons(1-10).
6. “Conrmpasscode”willbedisplayed.Enterasecondtimethesamepasscodeto
 re-conrm.
7. To disable passcode, select “Disable” as previously showed. And re-enter the
previous passcode to disable the lock.
When ATP is enabled, and if wrong passcode is entered for three times, a timer will be
activated. The next attempt will be possible only after the timer has elapsed. The timer
period will be increased with further wrong passcodes.
WARNING: If you choose to activate the passcode, please note your passcode
somewhere safe as a memory back-up in case you should forget it. This as there
is no way to reset the radio should the passcode be forgotten!
WARRANTY
This radio has a 2 year limited warranty.
WARNING ! Warranty becomes void once the radio cabinet has been opened or
any modications or alterations to the radio have been made !
The terms of the warranty of this radio do not cover the following:
- Damage caused by misuse, abuse, neglect, alterations, accidents or unauthorised
repair.
- Normal wear and tear.
- Breaking or bending of the metal telescopic antenna.
GB
GB
INFORMATION
This device is noise-suppressed according to the applicable EU
directives.
ThisproductfulllstheEuropeandirectives2006/95/EC,2005/32/EC
and 2004/108/EC.
This device conforms to the safety regulation DIN EN 60065 (VDE
0860)andthereforetheinternationalsafetyregulationIEC60065.
Never open the device casing. The manufacturer will not accept any
liability for damage resulting from improper handling.
The type plate is located on the bottom of the device.
Environmental note
This product has been made from high-quality parts and materials,
which can be reused and recycled.
Therefore, do not throw the product away with normal household waste
at the end of its life. Take it to a collection point for recycling electrical
and electronic device. This is indicated by this symbol on the product, in
the operating manual and on the packaging.
Pleasendoutaboutcollectionpointsoperatedbyyourlocalauthority.
Help protect the environmental by recycling used products.
Technical data
Power supply
Mains operation:
AC 230 V ~, 50/60Hz
Power consumption
Operation:≤85W
Standby:≤0,5W
Frequency coverage
FM 87,5 – 108,0 MHz
DAB 174,928 – 239,200 MHz
Speaker
Woofer 2 x Ø130mm, 4 ohms
Tweeter 2 x Ø45mm, 8 ohms
Output Power
Nominal 2 x 25W
Aux in socket
Ø3,5mm
Dimensions and weight
W x H x D: 485 x 306 x 263 mm
Net Weight: 6.6 kg

1 2
F
TABLE DES MATIERES
1. TABLE DES MATIERES……………………………………………........……………… 1
2. INSTRUCTIONS DE SECURITE IMPORTANTES………….……….......…………. 2
3. COMMANDES………………………………………………………............………... 3
4. ALIMENTATION ELECTRIQUE…………………………………………………… 4
5. FONCTIONS…………………………………….........................………… 4
6. PREMIERE UTILISATION DE LA RADIO……………............…………….. 5
7. M O D E D A B…………………………………………………..... . . . . . . .…………….. 5
8. M O DE FM ………………………………………………… . ... . . ... . . .……………… . 8
9. PRESELECTION DE STATIONS………………………………….…………………... 10
10. MODE AUX-IN……………………………………………….............……………. 10
11. REGLAGE MANUEL DE L’HEURE ET DE LA DATE…………..…………………… 11
12. V O L U M E E T S O N …………………………………… . . . . . . . . . ………………… 1 2
13. SONOR ITE……………………………............ ………………………………….. 12
14. SON ENVELOPPANT………………………........……………………………. 12
15. EGALISEUR…………………………………...........…………………………….. 13
16. ANTENNE TELESCOPIQUE EN METAL……….........……………… 13
17. SELECTION DE LA LANGUE………………………….…………………………14
18. VERSION DU LOGICIEL………………………………..…………………... 14
19. REINITIALISATION DU SYSTEME………………………..…………………..15
20. ECLAIRAGE DE L’ECRAN…………………………………….…………………..15
21. SYSTEMEDEPROTECTIONCONTRELEVOL(ATP)……………………….. 15
22. GA RANTIE…………………………………………………….. .... ..... .………….. 1 6
23. I N F O R M AT I O N S ……………………………………………… . . . . . . …………… . 1 7
AVERTISSEMENT : LA GARANTIE PREND FIN LORSQUE LE BOITIER DE
LA RADIO A ETE OUVERT OU LORSQUE DES MODIFICATIONS ONT ETE
APPORTEES A LA RADIO !
INSTRUCTIONS DE SECURITE IMPORTANTES
1. Lisez attentivement et complètement le mode d’emploi de la radio.
2. Conservez soigneusement ce mode d’emploi.
3. Tenez compte de tous les avertissements.
4. Suivez toutes les instructions.
5. Nettoyez la radio exclusivement avec un linge propre et sec.
6. N’obstruez pas les ouvertures de ventilation. Installez la radio conformément aux
instructions.
7. N’installez pas la radio à proximité de sources de chaleur (radiateurs, grilles de
 chauffage,foursetautresappareils(ampliscompris)quigénèrentdelachaleur).
8. Netenterjamaisdemodierleschesetprisespolariséesoucomportantunplotde
terre destiné à garantir votre sécurité. Une prise polarisée possède deux contacts,
dont l’un est plus large que l’autre. Une prise à plot de terre possède deux contacts
et un plot de mise à la terre. Le contact le plus large ou le plot de terre est prévu
 pourassurervotresécurité.Silacheducordond’alimentationdelaradione
s’adapte pas dans la prise de courant de votre installation, consultez un électricien
pour le remplacement de la prise de courant.
9. Protégez le cordon d’alimentation de la radio de manière à éviter tout dommage à
 celui-ci,enparticulierauniveaudelache,delaprisedecourantetdelasortiede
la radio.
10. Utilisez exclusivement les pièces et accessoires prévus par le fabricant.
11. Utilisez la radio exclusivement sur un support mobile, un présentoir, un trépied, un
support mural ou une table recommandé par le fabricant ou vendu avec la radio.
Lors de l’utilisation d’un support mobile, soyez prudent en déplaçant l’ensemble
support/radio, de façon à éviter de vous blesser en cas de chute de la radio.
12. Retirezlacheducordond’alimentationdelaradiodelaprisedecourantpendant
un orage ou lorsque la radio n’est pas utilisée durant un certain temps.
13. Coneztouteréparationoutoutentretienàunpersonnelqualié.Uneréparation
 ouunentretienestnécessairelorsquelaradio,lecordond’alimentationoulache
a été endommagé, lorsqu’un liquide a été renversé sur la radio et a pénétré dans
celle-ci, lorsque des objets sont tombés sur la radio et ont pénétré dans celle-ci,
lorsque la radio a été exposée à la pluie ou l’humidité, ou lorsque la radio est
tombée d’une certaine hauteur et ne fonctionne plus normalement.
14. And’évitertoutrisqued’incendieoud’électrocution,n’exposezpaslaradioàla
pluie ni à l’humidité.
15. Ne tentez jamais de démonter la radio. Celle-ci ne comporte aucun élément qui soit
réparable par l’utilisateur.
16. Ne posez jamais sur la radio des objets dégageant de la chaleur ou présentant une
 ammenue.
17. Lorsd’uneutilisationàl’airlibrepartempshumideoupluvieux,andeprévenir
le risque d’électrocution lorsque la radio a été exposée à l’eau ou la pluie, le cordon
 d’alimentationainsiquelachedoiventêtreparfaitementsecsavantd’insérerla
 cheducordond’alimentationdelaradiodansuneprisedecourant.
18. Laprisedecourantdoitêtreprochedelaradioetrestertoujoursaccessible,de
 sortequeseulelacheducordond’alimentationdelaradiodoitêtreretiréedela
prise de courant en cas d’urgence.
19. Les informations légales concernant la radio se trouvent sur la face inférieure de
celle-ci.
20. Cetteradioestprotégéecontrelesprojectionsd’eau(IPX4).
21. En cas d’interférences ou de dysfonctionnement de la radio suite à une décharge
 électrostatiqueouunesurtension,retirezunbrefinstantlacheducordon 
d’alimentation de la prise de courant et réinsérez ensuite celle-ci dans la prise de
courant.
ATTENTION : risque d’électrocution – ne pas ouvrir.