PERFECTPRO ROCKMATE User manual

3A81TZ6L00000
FM-RDS / Aux-in Digital
Tuning Worksite Radio
GB
NL
D
S
F
Operating instruction
Gebruiksaanwijzing
Bedienungsanleitung
Bruksanvisning
Mode d’emploi

1
Table of Contents
Important safety instructions .............................................. 2-3
Controls and connections ................................................... 4-6
Power the radio ........................................................................ 7
Charging the batteries ............................................................ 8
Using the radio for the first time ............................................ 9
Setting the clock time ............................................................. 9
Operating your radio - FM .............................................. 10-11
Presetting stations / Recalling a preset station ................. 12
Display modes – FM ............................................................ 13
FM Stereo Mono / Loudness ............................................... 14
Aux In Socket ........................................................................ 15
Specifications........................................................................16

2
GB
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves or other apparatus (including amplifiers) that
produce heat.
9. Protect the power cord from being walked on or pinched particularly
at plug, convenience receptacles, and the point where they exit from
the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for
long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally,
or has been dropped.
14. To reduce the risk of fire or electric shock, do not expose this
appliance to Rain or Moisture.
15. The Shock Hazard Marking and Associated Graphical Symbol is
provided on the back of unit.
16. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, shall be placed on the apparatus.

3
17. The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power slot.
18. Notice:
The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
19. Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable
20. A warning that batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire or the like.

4
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Preset 5
LCD display
Tuning / Seek control
Loudness ON/OFF
Stereo / Mono (FM only)
Info button
Speakers
Aux In socket
Standby (POWER ON/OFF)
Charging indicator LED
Source
Volume control
Preset 1
Preset 2
Preset 3
Preset 4
GB
Controls and connections

5
17.
18.
19.
20.
Battery compartment
AC power cord
FM antenna
Handle
Controls and connections
100~240V 50/60Hz 18W

6
21.
22.
23. AC cable hook Alkaline/NiMH/NiCad rechargeable battery switch
Storage compartment
GB
Controls and connections

7
Power the radio
1. Installing the batteries, first turn battery cover fixture anti-clockwise to
loosen and pull down the battery cover.
Note:
Before you insert the batteries, if you use non-rechargeable batteries,
make sure the NiMH/Alkaline switch is switched to Alkaline position.
2. Insert 6 x C size (UM-2) batteries into the compartment.
Ensure the batteries are completely inserted in accordance with the
diagram shown. Close the battery cover and fasten the fixture by
turning clockwise.
If the radio is not to be used for any extended period of time,
it is recommended that the batteries are removed from the radio.
Reduced power, distortion and a “stuttering sound”, or low battery
sign flashing on the LCD display are all signs that the batteries need
replacing or recharging (see below Charging the batteries).
Run time of the radio on batteries varies strongly depending on
the quality and capacity (mAh) of the batteries, temperature,
volume level etc.
3. AC Operation
Before plugging the AC power cord into the AC socket, be sure
the voltage is correct. If you have batteries in the radio and connect
AC power cord into the AC socket, the batteries will automatically
be disconnected.
AC cable hook is designed to store the cord when the radio is not
in use.

8
GB
Charging the batteries
Reduced power, distortion and a “stuttering sound” or low battery sign
flashing on the LCD display are all signs that the batteries need
recharged if you use rechargeable batteries to power the radio.
Note:
The radio can be charged only when the radio is off. Connect the AC
power cord into the AC socket to charge the batteries. Be sure the
battery type switch is set to Ni/MH position.
When the batteries are being charged, the red Charge LED will be on.
Charging time can take up to approx. 10 hours depending on the
battery capacity of the rechargeable batteries. When the batteries are
fully charged, the charged LED will be steady on green color.
Note:
Charge new batteries fully the first time before first use. This can take
longer depending on the capacity of the rechargeable batteries.
Do not use a mix of old and new rechargeable batteries.
Do not use a mix of full and empty rechargeable batteries.
Do not use batteries that have a different mAh capacity.
Do not use damaged or leaking batteries.

9
Using the radio for the first time
1. Place your radio on a flat surface.
2. Please press the Standby button to switch on your radio. It may be
necessary to relocate your radio to a position giving better reception.
You should then carry out a scan to find stations in FM.
Setting the clock time
1. Press and hold the Tuning knob until the hour digits of the clock
time begins flashing. Rotate the Tuning knob to choose the hour
digit as needed.
2. Press and release the Tuning knob to save the hour setting, and the
minute digits on the display will flash. Rotate the Tuning knob to
choose the minute digits as needed.
3. Press and release the Tuning knob to save the minute setting and
complete the clock setting. The radio will save your setting.
The radio will display saved time after clock time setting
is completed.
Note: The clock time setting can be done at power Off or On status.
You can also set the clock time with the FM RDS. This can
automatically set the time (CT)
Press the source to FM radio, select a FM radio station which provides
RDS CT service, the clock will be aligned in 2 minutes once the CT
service is available.
Once the FM radio station has been changed to one with RDS
CT service, the clock time will be aligned again.
1-3

10
GB
Operating your radio – Manual tuning FM
1. Press the STANDBY button to switch on your radio.
2. Press the SOURCE button to select FM band and stand up the
rubber antenna properly to get best FM reception.
3. Rotate the Tuning/Seek knob to tune required frequency in the
increment of 100 kHz.
4. Select required loudness setting and stereo / mono mode for
obtaining a best sounding quality.
5. A stereo symbol will appear on the LCD display if a stereo
broadcasting station is found.
6. Rotate the Volume control knob to get required sound level.
7. To turn off the radio, press the STANDBY button. Display will show
local time only.
2
1,7
6
3

11
Search tuning FM
1. Press the STANDBY button to turn radio on.
2. Select FM band by pressing the SOURCE button as described.
Stand up the FM rubber antenna properly to get best reception.
3. Press and release the Tuning/Seek knob, and the radio will seek
forward and stop automatically when it finds a radio station with
good signal. The radio will seek forward for the next available station
if pressing down the Tuning control knob again.
2
1
3

12
GB
Presetting stations
You may store your preferred FM radio stations to the preset station
memories (1 to 5). The procedure for setting presets and using them to
tune stations is described below.
1. Press the STANDBY button to turn on the radio.
2. Press the SOURCE button and tune to the required station as
previously described.
3. Press and hold the required Preset button (1~5) until radio beeps and
the display shows corresponding “PX” on the upper right corner.
4. Repeat this procedure for the remaining presets as you wish.
5. Stations stored in preset memories may be overwritten by following
above procedures if required.
Recalling a preset station
1. Press the STANDBY button to turn on the radio.
2. Press the SOURCE button to select FM band.
3. Momentarily press the required Preset button (1~5) to cause your
radio to tune to the station stored in preset memory.
2
3

13
Display modes – FM
On FM the bottom line of the display can be set to display any of the
following modes:
1. Press and release the Info button repeatedly to cycle through the
various modes:
a.
b.
c.
d.
e.
f.
Displays the name of the station being
listened to.
Displays type of station being listened to e.
g. Pop, Classic, News, etc.
Displays radio text messages such as new
items etc.
Displays the current RDS CT clock time
and date.
Displays system clock time.
Displays the signal strength for the station
being listened to.
Program service name
Program type
Radio text
Clock time
Time
Signal level

14
GB
FM stereo / mono
1. If an FM station is received with a weak signal some hiss may
be audible. To reduce the hiss press and release the
STEREO/MONO button so that the Stereo indicator on the display
is cancelled. Your radio will switch to mono mode.
2. To return to stereo mode press and release the STEREO/MONO
button so that Stereo indicator on the display is visible. The radio will
switch to stereo mode.
Note:
This radio will always auto detect if there is stereo signal when you set
the radio in Stereo mode. If there is not a stereo signal, the stereo mark
will be cleared.
Loudness On/Off
Press the Loudness button to get compensation on lower and
higher frequency. The effect will be more audible when the radio is in
lower volume level. Display will show Loudness ON when Loudness
function is applied.
Note: Default is Loudness OFF
1,2

15
Aux In Socket
There is a Aux In socket on this radio to connect external audio sources
like a MP3 player to the speakers of this radio.
The Aux In socket is located on the side of the radio. Remove the
rubber cover and connect the audio source with a 3.5 mm stereo
audio cable.
When radio is on, repeatedly press and release SOURCE button to
select AUX-IN, rotate the volume control to play the audio program.
Please always close rubber cover (AUX-in) on the side of the
radio when AUX input socket is not in use. This is to prevent
moist and dust from entering the radio. This will also enhance
overall sound quality.
LCD illumination
When radio is switched on, press any button except the POWER
button will illuminate the LCD display for approx. 10 seconds. However if
you use AC cord to power the radio, the LCD display will be always
illuminated until you turn the radio off by pressing POWER button.

16
GB
Specifications
Frequency range:
FM 87.50 – 108 MHz
AC Power:
AC 100 - 240V / 50-60HZ / 18W
Batteries:
ALKALINE battery
6 X C size (UM-2)
Rechargeable battery:
Ni-MH or Ni-cad 6 X C size
Speaker:
3” x 2, 8 ohm, 12W full range waterproof-stereo
Output Power:
3W+3W 10% T.H.D. @ 1 kHz @ battery 9V
5W+5W 10% T.H.D. @ 1 kHz @ AC 100 – 240V
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be
disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling
advice. (Waste Electrical and Electronic Equipment Directive)

17
Inhoudsopgave
Belangrijke veiligheidsinstructies ................................. 18-19
Bedieningselementen en aansluitingen ...................... 20-22
De radio van stroom voorzien ............................................. 23
De batterijen vervangen ....................................................... 24
De radio voor het eerst gebruiken ...................................... 25
De klok instellen .................................................................... 25
Uw radio bedienen - FM ................................................. 26-27
Voorkeurszenders instellen/
Voorkeurszenders oproepen ............................................... 28
Displaymodi – FM ................................................................ 29
FM Stereo Mono / Loudness ............................................... 30
Aux In-aansluiting ................................................................. 31
Specificaties..........................................................................32

18
NL
Belangrijke veiligheidsinstructies
1. Lees deze instructies.
2. Bewaar deze instructies.
3. Neem alle waarschuwingen in acht.
4. Volg alle instructies.
5. Gebruik het apparaat niet in de buurt van water.
6. Alleen schoonmaken met een droge doek.
7. Blokeer de ventilatieopeningen niet. Installeer in overeenstemming
met de instructies.
8. Niet installeren in de buurt van warmtebronnen zoals radiatoren,
kachels of andere apparaten (inclusief versterkers) die
warmte producten.
9. Voorkom dat er op het netsnoer wordt gestapt of dat deze
wordt geperforeerd, voornamelijk bij de stekkers, stopcontacten en
de aansluiting van de kabel op het apparaat.
10. Gebruik alleen koppelstukken/accessoires die zijn gespecificeerd
door de fabrikant.
11. Gebruik alleen met een wagentje, standaard, driepoot of tafel die is
gespecificeerd door de fabrikant of verkocht met het apparaat.
Als een wagentje wordt gebruikt, wees dan voorzichtig wanneer u
het wagentje/apparaat verplaatst om verwondingen door omvallen
van het wagentje te voorkomen.
12. Haal de stekker uit het stopcontact tijdens onweer of als het
apparaat niet wordt gebruikt voor lange perioden.
13. Laat alle onderhoud over aan gekwalificeerd onderhoudspersoneel.
Er is onderhoud nodig als het apparaat is beschadigd,
bijvoorbeeld als het netsnoer of de stekker is beschadigd,
vloeistof is gemorst op het apparaat of er voorwerpen in het apparaat
zijn gevallen, het apparaat is blootgesteld aan regen of vocht,
niet normaal werkt of is gevallen.
14. Om het risico van brand of elektrische schokken te verminderen,
stel het apparaat niet bloot aan regen of vocht.
15. De Schokgevaar-markering en het bijbehorende symbool staan op
de achterkant van het apparaat.
16. Het apparaat moet niet worden blootgesteld aan druppend en
spattend water en er mogen geen voorwerpen gevuld met vloeistof
op het apparaat worden geplaatst.

19
17. De stekker moet dicht bij de radio zijn en eenvoudig bereikbaar zijn
in geval van nood, om de radio te ontkoppelen van het stroomnet,
haal de stekker uit het stopcontact.
18. Opmerking:
De veranderingen of aanpassingen die niet zijn goedgekeurd door de
partij verantwoordelijk voor de naleving kan de autoriteit van de
gebruiker om het apparaat te bedienen ongeldig maken.
19. Wanneer de stekker of een koppelstuk wordt gebruik
als ontkoppelapparaat, het ontkoppelapparaat moet eenvoudig
bedienbaar blijven.
20. Waarschuwing: batterijen (geïnstalleerde accu’s of batterijen) mogen
niet worden blootgesteld aan extreme warmte, zoals zonlicht,
brand en dergelijke.