PARTS LIST
SPECIFICATIONS
Air Inlet / Outlet:.......................................................1/4"- 18 NPT
Recommended Air Pressure ............................................ 5-1/8"
Air Hose.......................................................... 3/8" Dia. x 30 Feet
Air Flow ...........................................................25 CFM Maximum
Hose Reel Capacity ..........................................................50 Feet
Maximum PSI ..........................250 PSI, 750 PSI Burst Pressure
Overall Dimensions................. 10-5/8" L x 14" W x 12-11/16" H
Specifications are subject to
change without notice
IMPORTANT SAFETY INFORMATION
Installation
Warning: When unpacking, check to make sure
the parts listed on page 4 are included. If any
parts are missing or broken, please contact
Performance Tool®as soon as possible.
1. You may mount your Hose Reel on a wall,
workbench, or a ceiling. The surface you mount
to must be capable of holding the weight of the
Hose Reel, the hose, and the additional stress
from tugging on the unit with the hose extended.
2. Mount the unit through the four mounting holes
on the Base (#1) with four bolts (not included)
fitted for 13/32” diameter holes.
3. Thread the Handle (#23) onto the
Flange A (#6)assembly.
OPERATION
Warning: Do not exceed 250 PSI with this
Hose Reel.
1. You may need to prepare a 1/4” air connector
(sold separately) to connect to the air source
hose.
2. Wrap the 1/4” air connector (not included) with
pipe thread seal tape before connecting the air
source hose to the Input Valve (#24) on the
Hose Reel. The Hose on the Hose Reel comes
pre-attached to the Swivel (#13).
3. Check the air connection for leaks.
4. When using the Hose Reel, remove hose from
reel slowly. If it binds up, do not force it.
5. When reeling on hose, make sure the hose
covers the Hose Reel evenly, and does not
bunch up on either end.
1. Periodically check connection for air leaks.
2. Keep the hose clean and free of dirt and debris
by wiping it down before winding it on to the
Hose Reel.
CARE & MAINTENANCE
Read these safety warnings before operation.
WARNING!
Failure to heed these warnings may result
in loss of load, damage to jack, and/or jack
failure resulting in personal injury or property
damage.
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines
or power tools in damp or wet locations. Don’t expose
to rain. Keep work area well lighted. Do not use
electrically powered tools in the presence of flammable
gases or liquids.
3. Keep children away. Children must never be allowed
in the work area. Do not let them handle machines,
tools, or extension cords.
4. Store idle equipment. When not in use, tools must be
stored in a dry location to inhibit rust. Always lock up
tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force
a small tool or attachment to do the work of a larger
industrial tool.There are certain applications for which
this tool was designed It will do the job better and more
safely at the rate for which it was intended. Do not
modify this tool and do not use this tool for a purpose
for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry
as they can be caught in moving parts. Protective,
electrically non-conductive clothes and non-skid
footwear are recommended when working. Wear
restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI
approved impact safety goggles.
8. Do not overreach. Keep proper footing and balance at
all times. Do not reach over or across running machines
or air hoses.
9. Maintain tools with care. Keep tools clean for better and
safer performance. Follow instructions for lubricating
and changing accessories. Inspect tool cords and air
hoses periodically and, if damaged, have them repaired
by an authorized technician. The handles must be kept
clean, dry, and free from oil and grease at all times.
10. Disconnect air supply. Disconnect air hose when
not in use.
11. Stay alert. Watch what you are doing, us
common sense. Do not operate any tool when you are
tired.
12. Check for damaged parts. Before using any tool, any
part that appears damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment and
binding of moving parts; any broken parts or mounting
fixtures; and any other condition that may affect proper
operation. Any part that is damaged should be properly
repaired or replaced by a qualified technician.
13. Replacement parts and accessories. When servicing,
use only identical replacement parts. Use of any other
parts will void the warranty. Only use accessories
intended for use with this tool Approved accessories
are available from Performance Tool®.
14. Do not operate air tool if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate
the tool.
15. Maintenance. For your safety, maintenance should be
performed regularly by a qualified technician.
WARNING: This product and its packaging contain a
chemical known to the State of California to cause
cancer, birth defects, or other reproductive harm.
Warning: The warnings, cautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It
must be understood by the operator that common sense
and caution are factors which cannot be built into this
product, but must be supplied by the operator. Read
and understand all of the instructions provided in the
instruction manual of the Air Hose
Reel being used.
Page 1 Page 2 Page 3
