Perfomance Tool W41044 User manual

1
14
14
15
15 16 18
16
14
14
20
15 16
17
10
19
2
11
11
13A
21
12
3
4
5
6
7
8
9
13B
TRANSMISSION ADAPTOR
300 LB. CAPACITY
OWNERS MANUAL
Stock Number W41044
On occasion, after printing of our literature is completed, our manufacturers may make changes and/or modifications to
merchandise which will not be reflected in this manual. Although we strive to maintain complete and accurate information, it
is possible in some instances, that the product may differ slightly from printed specifications. Illustrations are intended for
reference only. Actual merchandise may vary. Wilmar is not responsible for typographical errors.
Please read these instructions carefully and retain them for future use.

Read these safety warnings before operation.
WARNING!
Failure to read, understand and follow these warnings may result in loss of load, damage
to unit, and/or failure of unit resulting in personal injury or property damage.
WARNING!
Use this transmission adaptor only for the removal and installation of passenger car and light
duty truck transmissions. Do not overload beyond 300 lbs. Do not remove or install
transmissions with transfer cases attached.
Jack must be in fully lowered positon to move load.
Always secure transmission in place with safety chain.
Use only with heavy frame service jack with removable saddle. (See example on back page)
Read, understand and follow all warnings listed in jack instruction manual.
Vehicle must be properly supported before starting repair. Refer to vehicle owner’s manual for
proper jacking procedures.
This unit is designed for use only on hard level surfaces capable of sustaining the load. Use of
unit on other than hard level surfaces can result in instablility and possible loss of load.
IMPORTANT SAFETY INFORMATION
1. Visual inspection must be made before each use of this unit, checking for cracks, cracked welds
and missing and/or damaged parts. Any unit that appears to be damaged in any way must be
removed from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS
ASSOCIATED WITH THE MISUSE OF EQUIPMENT
OF THIS TYPE, NO MODIFICATIONS SHALL BE
MADE TO THE PRODUCT.
3. Keep adaptor well lubricated at all points shown in
drawing at right.
4. Replace worn or damaged parts with Performance
Tool replacement parts. Be sure that only qualified
personnel perform repairs.
CARE & MAINTENANCE
1
14
14
15
15 16 18
16
14
14
20
15 16
17
10
19
2
11
11
13A
21
12
3
4
5
6
7
8
9
13B
Oil Oil
1. Install Threaded Bushing (3), into holes in Platform (1) using Large Snap Rings (11) as shown.
2. Screw Adjustable Tilt Knob (2) through threaded bushing approximately half way.
3. Install 2 Lock Nuts (13A) approximately 3” from end of threaded shaft.
4. Install Non-Threaded Bushing (4) into holes in Pivot Frame (5) using Large Snap Rings (11)
as shown.
5. Slide Non-Threaded Bushing over onto threaded shaft and install remaining Lock Nut (13B).
6. Connect Platform (1) to Pivot Frame (5) using Pivot Pin (6), Small Snap Rings (12) and
Spacers (21) as shown.
7. Bolt on Mounting Bracket Frames (7) and Mounting Brackets (8).
ASSEMBLY INSTRUCTIONS

Assembly Diagram
1
14
14
15
15 16 18
16
14
14
20
15 16
17
10
19
2
11
11
13A
21
12
3
4
5
6
7
8
9
13B
1 Platform 1
2 Adjustable Tilt Knob 1
3 Threaded Bushing 1
4 Non-Threaded Bushing 1
5 Pivot Frame 1
6 Pivot Pin 1
7 Mounting Bracket Frame 2
8 Mounting Bracket 4
9 Chain Hook Assembly 1
10 Safety Chain 1
11 Large Snap Ring 4
12 Small Snap Ring 2
13 Lock Nut with Set Screw 3
14 M10 x 25 Bolt 7
15 M10 Washer 7
16 M10 Nut 7
17 M8 x 25 Bolt 1
18 M8 Washer 2
19 M8 Nut 1
20 Large Retaining Washer 1
21 Spacer 2
Part # Description Qty. Part # Description Qty.
Parts List
8. Install Chain Hook Assembly (9) and Safety Chain (10) as shown.
9. Install Assembled Adaptor onto Service Jack Saddle Frame securing with Bolt (14)
and Washer (20).

LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These
warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington
governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights
which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal
use and service. A defective product may be returned for a free replacement within 90 days from the date of
purchase, provided that product is returned to place of purchase immediately after discovery of defect. After 90
days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any parts which
our examination shall disclose to be defective and under warranty. These warranties shall be valid only when a sales
receipt showing the date of purchase accompanies the defective product or defective part (s) being returned. For
part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be
replaced under normal use and service. These warranties shall not apply to any product or part which is used for a
purpose for which it is not designed, or which has been repaired or altered in any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse,
neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in
connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no
express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes
no implied warranty of merchantability and no implied warranty of fitness for any particular purpose, except that for
goods purchased primarily for personal, family or household use and not for commercial or business use,
PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied
warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in
all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any
manner related to any product, or to the design, use, or any inability to use the product. The sole and exclusive
remedy for a defective product or part shall be the repair, or replacement thereof as provided above. The laws on
limitation of remedies or on consequential, incidental or special damages may vary from state to state, so the above
limitations may not apply in all cases.
© Copyright 2015 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
Example of
heavy frame
service jack