Perlick 4410QC-2 Owner's manual

INSTALLATION AND OPERATION INSTRUCTIONS
4400QC SERIES POWER PAKS
IMPORTANT INFORMATION
To register your product, visit our web site at
perlick.com. Click on Commercial, then Service.
You will see the link to Warranty Registration Form.
You must complete and submit this form or the
installation date will revert back to the ship date.
Permanently mount the enclosed Warning/Safety
Instruction label in a visible location near the CO2
regulator.
This manual has been prepared to assist you in the
installation of your 4400QC Series Power Pak and to
acquaint you with its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer can
provide you with a list of qualified service agents.
For your own protection, never return merchandise
for credit without our approval.
We thank you for selecting a Quick Chill product and
assure you of our continuing interest in your
satisfaction.
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone [phone] • Fax [phone]
Toll Free 800.558.5592 • E-Mail [email protected] • www.perlick.com
Table of Contents
Sizes & Specications ............................................ 2-3
General Information.......................................... 3
Installation ..................................................... 3-4
Connecting Power Pak to Trunk Housing........... 4-5
Power Pak Start-Up................................................ 5-6
LEDS ......................................................................6-7
Preventative Maintenance...................................... 6-7
Replacement Parts.................................................... 7
Wiring Diagrams........................................................ 8
Form No. Z0507QC
Rev. 06.01.23
C
US
MODELS
Compressor Size 1/3 HP 1/2 HP 3/4 HP 1-1/2 HP
# of
Circulating
Pumps
1 4404QC 4410QC 4414QC 4420QC
2 4410QC-2 4414QC-2 4420QC-2
3 4420QC-3

MODEL NOS. 4404QC 4410QC 4410QC-2 4414QC 4414QC-2 4420QC 4420QC-2 4420QC-3
DIMENSIONS:
EXTERIOR
(mm)*
Length “A” 24-1/4" (616) 26-3/4" (680)
Width “B” 17-1/4" (439) 20-1/4" (515)
Height “C” 25-1/2" (648) 31" (788)
*A minimum of six inches of clearance should be allowed around the entire unit for proper performance. Additional Clearance should be considered for above the
unit and in front of the unit for serviceability.
ELECTRICAL Voltage 120V 115-208/230V **
Frequency 60 Hz
Phase 1 Ø
RLA (Rated
Load Amps) 14.4 15.7 21.8 20.6 26.2 21.9 24.7 27.5
MCA (Min. Circuit
Ampacity) 16.4 18.0 24.1 24.0 29.6 26.6 29.2 32.0
MOCP (Max. Over-
Current Protection) 20 25 30 35 40 40 45 50
COMPRESSOR (Horse Power) 1/3 1/2 3/4 1-1/2
EVAPORATOR RATING @ 20°F (BTUH) 2550 3800 6000 12000
HEAT of REJECTION MAX (BTUH) 4080 6080 9600 19200
REFRIGERATION Constant Pressure Expansion Valve, Condensing Unit with Service Valves
REFRIGERANT (TYPE) R-134a
REFRIGERANT CHARGE 14.0 oz/397g 12.0 oz/340g 14.0 oz/397g 16.0 oz/454g
SHIPPING WEIGHT LBS (kg) 140 (64) 138 (63) 150 (69) 167 (76) 180 (82) 217 (99) 230 (105) 245 (112)
CABINET Black Vinyl Clad Galvanized Steel
CIRCULATING PUMP 70 GPH / 80 PSIG (MAX)
RESERVOIR CAPACITY 1.75 Gallons
GLYCOL CONCENTRATION 30%
OPTIONAL ACCESSORIES
(Sold Separately)
• C22296A-20 - Power Cord Kit for 4404QC & 4410QC Single Pump Units Only (NEMA 5-20P)
• 57782 - Adjustable Legs (Set of 4)
• 61468 - Overow Bottle Kit
• 63299-1 - Food Grade Glycol Pre-Mix (1 gallon)
• 61790A2 - Dual Tier Rack
• 61790A3 - Triple Tier Rack
• C21499SS - Stainless Steel Table Stand
• 4408SS - Wall Bracket for 4404QC & 4410QC Only
**4-WIRE AC POWER SOURCE REQUIRED
AC - 115-208/240V, 60Hz, Split Single Phase
(Ground, Neutral, Hot-Power, Hot-Power)
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
2
4400QC SERIES POWER PAKS  AIR COOLED
 INSTALLATION AND OPERATING INSTRUCTIONS
WARNING: California Prop 65 Noce
These products may expose you to chemicals including
Chromium, which are known to the state of California
to cause cancer and birth defects or other reproducve
harm. For more informaon on whether a product in this
list contains these chemicals, please refer to the specic
product page at perlick.com. Or to nd out more about
Prop 65, go to P65Warnings.ca.gov.
C
US

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
3Form No. Z0507QC
Rev. 06.01.23
4400QC SERIES POWER PAKS  AIR COOLED
 GENERAL INFORMATION
PRODUCT DESCRIPTION
Power Paks have always been an integral part of a Beer
System. The 4400QC Series Power Pak product line has
been expanded to satisfy longer beer runs. A Power Pak
circulates coolant solution (food grade propylene glycol with
distilled water) from the walk-in cooler to the dispensing
station(s) and back, maintaining the desired dispensing
temperature at the faucet. The 4400QC Series Power Paks
incorporate a 1/3 hp ball bearing, maintenance free motor
with a 70 gallon per hour 80 psig positive displacement
pump for optimum performance. The 4400QC series
Power Pak product line employs a direct expansion form
of refrigeration increasing the units’ efficiency as well as
making the units more compact. These units also employ
an electronic temperature control with digital readout. This
state of the art control, controls the performance of the unit
as well as giving the user a visual indication of how the unit
is working as well as early indication if something may be
going wrong through the use of internal alarms.
Accessories
Power Cord Kit
C22296A-20 – 12/3 Cord, 20A, Nema Plug 5-20P,
Dedicated Circuit Models – See electrical specifications.
NOTE: Use only with 4404QC and 4410QC Single Pump units only.
Power Pak Racks
61790A2 Dual Tier Rack, 61790A3 Triple Tier Rack –
All Models
Power Pak Wall Mounting Brackets
4408SS – For Models 4404QC and 4410QC only
Coolant Solution – 63299-1
Food Grade Glycol Pre-Mix (1 Gallon)
Coolant Connector Kit
C23015 – All Models
Leg Set – All Models
57782 – Set of four, 5 3/4”-7 1/2” adjustable legs
INSTALLATION – 4400QC Series Power Paks
IMPORTANT SAFETY WARNINGS!
• Follow all National and Regional Codes.
• Read Installation and Operating Instructions carefully before attempting to install, operate or maintain the product.
• Protect yourself and others by observing all safety information.
• Electrical hazards exist and can cause injuries if not serviced by properly trained personnel.
• Failure to comply with instructions could result in personal injury and/or property damage!
• Retain instructions for future reference.
• Never operate the circulating pump without coolant in the reservoir.
NOTE: Air-cooled Power Paks must be installed in areas with adequate ventilation to maintain ambient temperatures
of less than 105°F to achieve optimum performance and satisfy warranty requirements.
INSTALLING THE POWER PAK
Prior to installing a 4400QC Series Power Pak, it is imperative that the method of connecting it to the electrical service has been
determined. Ensure that the electrical service to power the Power Pak will handle the load requirements. Perlick has a Power
Cord specifically designed for a Power Pak, which has a RLA of 16 amps or less, and a MCA of 20 amps or less. All units with
RLA greater than 16 amps and a MCA of greater than 20 amps should have the Power Pak hard-wired to electrical service.
PRODUCT/SERVICE/WARRANTY INFORMATION
To Obtain Product Information
• Contact your selling dealer.
• Inquire on the web at perlick.com.
• Call 800-558-5592 for factory assistance for information,
planning, installation or product information.
• Write Perlick Corporation, Customer Service Department,
8300 W. Good Hope Road, Milwaukee, Wisconsin 53223.
• E-mail us at [e-mail].
To Obtain Product Service, Replacement Parts or Accessories:
Use only genuine Perlick replacement parts and accessories. Genuine
Perlick parts and accessories are designed to work correctly with
Perlick products and oer superior service life. The use of non-Perlick
parts can damage the unit and may void the warranty.
Check the model and serial number of the unit located on the label
attached to the inside top of the cabinet.
Call a Perlick Factory Authorized service center. For the location of the
nearest Service Center, contact your dealer, or inquire via the web at
perlick.com, or write to:
Perlick Corporation, Customer Service Department,
8300 W. Good Hope Road, Milwaukee, Wisconsin 53223,
call 800-558-5592, or e-mail us at:
[email protected].

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
4
4400QC SERIES POWER PAKS  AIR COOLED
 INSTALLATION
ALL MODELS
• Determine the ideal placement of the Power Pak.
Locate the connection point to the truck housing
and place the Power Pak as close to this point as
possible. NOTE: If the Power Pak is to be located
on top of the walk-in cooler, it is imperative
that proper ventilation is provided to prevent
system failure due to overheating. Inadequate
ventilation will void warranty.
• Place the Power Pak and Ensure that it is level to
provide proper overflow protection. REMINDER:
Allow a minimum of six inches of clearance
on the louvered ends of the cabinet for proper
airflow. Allow accessibility room on the top of
the cabinet for serviceability.
• Remove the top panels (2).
• Ensure Power Switches for Condensing Unit and
Pump(s) are in the OFF position. Make the electrical
connections per their illustrations. NOTE: Electrical
circuit should be a dedicated circuit for use only
with the Power Pak. The circuit should be sized in
accordance with the electrical requirements of each
unit as well as in compliance with all National and
Local Codes.
• Plumb overflow port to a suitable reservoir/drain.
CONNECTING POWER PAK TO
TRUNK HOUSING
4400QC Series Power Paks require rigid fittings with
a minimum pressure rating of 150 psig. Use Coolant
Connector Kit C23015 to connect Power Pak to
Trunk Housing.
■ Inspect pump outlet port for debris. Insert barbed
fitting into pump outlet port.
■ Inspect Glycol Return Manifold inlet for debris.
Insert barbed fitting into return manifold inlet port.
■ Cut supplied coolant tubing, to required length to
reach from Power Pak to Trunk Housing connection
point.
■ Cut tubular insulation sleeve, in half and install over
previously cut coolant tubing.
■ Take oetiker clamps, and install over coolant
tubing ends.
■ Push coolant lines, one each over pump outlet
barbed fitting and return manifold barbed fitting.
■ Position oetikers over barbed fitting and clamp
securely.
■ Slide tubular insulation sleeves tightly against
connection points. Use insulation tape as
necessary to ensure an air tight seal to prevent
excessive heat gain or condensation problems.
■ Drill a 3 1/2 ” diameter hole in walk-in cooler to
accommodate coolant lines.
■ Install insulating donuts over hole (both inside
and outside of cooler walls).
■ Slide large insulation sleeve, over remaining coolant
tubing exposed to warm air conditions including
inside walk-in cooler from Power Pak to Trunk
Housing connection point. Seal and tape all seams
to prevent excessive heat gain or condensation
problems.
■ Slide coolant lines through 3 1/2 ” donut hole
previously cut in walk-in cooler wall.
■ Position Trunk Housing coolant lines and Coolant
Connector kit lines in horizontal position, to alleviate
condensation runoff into Trunk Housing.
■ Cut Trunk Housing coolant lines with tubing cutter
to ensure clean burr free ends.
■ Take oetiker clamps and install over coolant
connector kit tubing ends.
■ Slide coolant connector kit tubing over the
trunk housing coolant lines and secure using
above oetikers.
■ Complete the insulation process by ensuring that
all coolant lines are well insulated including all
seams to prevent excessive condensation and
heat gain.
■ Seal donut hole to ensure an air tight seal to prevent
walk-in cooler problems as well as condensation.

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
5Form No. Z0507QC
Rev. 06.01.23
4400QC SERIES POWER PAKS  AIR COOLED
 CONNECTION TO TRUNK HOUSING
POWER PAK START-UP
4400QC SERIES POWER PAKS
Use only Quick Chill Approved Coolant Solution,
#63299-1, all other solutions and mixtures will void the
warranty. The Coolant Solution has been pre-mixed for
Optimum performance and wear protection. The
Power Pak reservoir holds approximately 1.75 gallons
of solution. It takes approximately 1 gallon of Coolant
Solution to fill every 60 feet of Trunk Housing.
■ Never operate the circulating pump without
coolant in the reservoir.
■ Fill Power Pak reservoir with Quick Chill Coolant
Solution.
■ Turn condensing unit switch and pump switch to
the ON position. Coolant solution level will begin to
drop in reservoir.
■ Continue adding Quick Chill Coolant Solution until
no air bubbles are apparent from the Coolant
return line.
NOTE: Never allow for the Coolant level in the
reservoir to drop below the heat exchanger tube
inlet. Allowing the level to drop below the inlet will
allow air bubbles into the lines.
■ Fill Power Pak reservoir until both the return
line fitting port and the overflow tube port are
submersed under Coolant Solution. Watch return
line fitting port for additional air bubbles as this
may signify additional Coolant Solution may need
to be added.
■ Thoroughly check all field connection points for
leaks.
■ Monitor Power Pak Temperature read-out to
ensure Power Pak is working properly. Depending
on length of trunk housing run and surrounding
ambient conditions, these factors will determine
how long it takes for the Power Pak to cut-out on
the temperature control.

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
6
4400QC SERIES POWER PAKS  AIR COOLED
 POWER PAK STARTUP
DIGITAL TEMPERATURE CONTROLLER
The 4400QC Series Power Pak comes equipped with a Factory Programmed Electronic Thermostat with
Display. The Thermostat has numerous factory settings, which should never be adjusted or tampered
with to ensure proper operation of the Power Pak. The Thermostat has been factory programmed to
cut-out at 30°F with a hysteresis/differential of 4°F.
Alarm Meaning Action
E1 Probe failure Numerous - see note 1
NOTE 1: Faulty probe, loose connection, broken wire (Power Pak will
continue to operate with a faulty probe). The controller has been factory
programmed to continue operation with the compressor cycling on and off
in 5 minute intervals.
To Adjust the Temperature Set Point (Figure 1):
1. Press the button. The label “SET” will be
displayed.
2. Press the button a second time. The set point
will be displayed.
3. To change the Set point value, press the or
keys within 15 seconds.
4. Press to conrm the new setpoint value.
5. After 10 seconds the display will return to
indicating the cabinet temperature.
Figure 1: Digital Temperature Controller
On/O:
Press the ON/OFF button to turn the unit on or o.
Key Combinations:
Press the UP and DOWN arrow buttons to
lock and unlock the keyboard.
Press the SET and DOWN arrow buttons
simultaneously to enter programming
mode.
Press the SET and UP arrow buttons si-
multaneously to return to room tempera-
ture display.
LED Functions
The following table describes LED functions
LED Mode Function
ON Compressor is on
Flashing Delay, protection or
Blocked start-up
ON Defrost is on
Flashing Manual or D.I. activation
ON Alarm is on
Flashing Alarm acknowledged
ON Evaporator is on

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
7Form No. Z0507QC
Rev. 06.01.23
4400QC SERIES POWER PAKS  AIR COOLED
 LEDS & PREVENTATIVE MAINTENANCE
COMPONENT ALL MODELS
Pump 63562
V-Clamp 63291-2
Constant Pressure Exp
Valve
63826
Switch 63303
Drier 63297
COMPONENT/MODEL 4404QC 4410QC 4414QC 4420QC
Condensing Unit 668HE5108AA (1012125) 559HG5110HA
(C22667
M7GH-H083-
CFA-121 (1022593)
FPAK-015Z-
CFV-140 (C22668)
Compressor 268HE71 (1015091) 269HG9290AF
(C22999CMP05) RRT10K1E-PFA-901 ZS19KAE-PFV-818
Cond Fan Motor 1450076 (C22999FMTR01) 1450095
(C22999FMTR02)
950-0367-00 950-0265-00
Fan Blade 2455003 (C22999FBLD01) 2455003
(C22999FBLD01)
083-0033-01
Start Components US-PBNEU6210Z1
(1015092)
US-PBNEK6214Z1
(C22999STCP07)
Relay-Potential Kit 940-0046-26 940-0001-79
Start Capacitor Kit 914-0036-16 914-0036-03
Run Capacitor Kit 914-0037-12 914-0017-36
Pump Motor 63292 63292 63293 63293
Heat Exchanger 63300B 63300B 63301B 63302B
Gasket, Heat Exchanger 61758A 61758A 61758A 61758A
Grille 64197-3B 64197-3B 64197-3B 64285-1B
Front Panel 64407-1B 64407-1B 64407-1B 64286-1B
Contactor 63359
Relay, Pump 63358
Access Panel 1018561-1B
REPLACEMENT PARTS
COMMON COMPONENTS
PREVENTATIVE MAINTENANCE
Clean Condenser
Condenser, located behind the grille, should be cleaned as required of all dirt and debris, at minimum every
3 months, more frequently if required. Use soft bristle brush and/or vacuum to remove dust and debris, avoid
damaging the condenser fins.
Coolant Solution
Periodically check coolant solution level and concentration. Added or replace the coolant solution with Perlick
Coolant Solution if required.
Coolant Solution 63299-1
Temperature Control Kit 1008503
Temp Control 1007439
Probe 1050282
Compression Fitting 1008057
Wire Harness 61834-2

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specications without prior notice
8
4400QC SERIES POWER PAKS  AIR COOLED
 WIRING DIAGRAMS
RECEPTACLE
*BLM2000
MTR
PUMP
1
2
MTR
PUMP
1
2
WHITE
RED
WIRING DIAGRAM FOR 4404QC, 4410QC, 4414QC 115V POWER PAKS
SENSOR
FIELD CONNECTIONS
*INDICATES OPTIONAL ACCESSORIES
SUGGEST HARD WIRED AS NORMAL MODE OF ATTACHMENT SUPPLIED BY OTHERS.
CORD SET (TO WALL OUTLET) C22297-20 FOR STANDARD UNIT ONLY,
DANGER: ELECTRICAL SHOCK HAZARD. DISCONNECT ALL POWER BEFORE SERVICING.
1
BLACK COPY ON WHITE BACKGROUND
INDIVIDUAL PIECES, SQUARE CORNERS WITH
MATERIAL: 2 MIL. WHITE POLYESTER PAPER
1/4" TOP TAB FOR EASY LINER REMOVAL
ADHESIVE: 3M 350 ADHESIVE U.L. & CSA APPROVED
NOTES:
PUT UP:
COLOR:
NOTE:
NUETRAL
GROUND
HOT (POWER)
BLACK
BLACK
BLACK
BLACK
WHITE
BLACK
10"
TO CONDENSING UNIT
WHITE
ELECTRONIC TEMPERATURE
4-1/2"
BLACK
CONTROL
FORM NO. 1008363
NOTE: SCORE LABEL ONLY ON THIS LINE
1/4"TAB TO BE REMOVED WITH LINER
WHEN INSTALLING
1/4"
SENSOR
SUPPLY
SENSOR
D.I.
Pb1
180 FT.
3
540 FT.
9
10
10
600 FT.
570 FT.
360 FT.
6
8
9
8
7
7
450 FT.
510 FT.
480 FT.
420 FT.
390 FT.
5
6
5
4
4
270 FT.
330 FT.
300 FT.
240 FT.
210 FT.
Length
1
Coolant
2
3
2
1
90 FT.
150 FT.
120 FT.
60 FT.
30 FT.
(Gallons)
Trunk
For 2-12
Beverage Lines
For 16-24
Beverage Lines
6
18
20
19
12
15
17
16
14
13
9
11
10
8
7
1
3
5
4
2
COOLANT REQUIREMENTS
WHITE
WHITE
WHITE
REVISIONS
REV ECO DESCRIPTION DESIGNER DATE APPROVED BY
D 2022-5777 UPDATE WIRING DIAGRAM WITH NEW TERMINAL BLOCK DPD 10/14/2022
DESCRIPTION
PART NUMBER
DRAWING NUMBER
MATERIAL:
REFERENCE:
SCALE: 1:1
1008363 1008363
WIRING DIAGRAM LABEL FOR QC POWER PAKS
HOLES: .0135 THRU .125: .004
.1260 THRU .250: .005
.2510 THRU .500: .006
.5010 THRU .750: .008
.7510 THRU 1.000: .010
1.001 & UP: .012
BREAK SHARP EDGES - .015 X 45°
RADIUS SHARP FILLETS - .015 TO .031
DIMENSIONS ARE IN INCHES TOLERANCES:
UNLESS OTHERWISE SPECIFIED:
Ang =
Frac = 1/8
THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK CORPORATION. COPYRIGHT 2015 PERLICK CORPORATION. ALL RIGHTS RESERVED.
Milwaukee, Wisconsin
Perlick Corporation
SEE NOTES
A A
B B
C C
D D
4
4
3
3
2
2
1
1
.X =
.XX =
.XXX =
OVERALL DIMENSIONS: 10 INCH X 4.5 INCH GAUGE: REQ QUAL MFG: WEIGHT:
Form No. Z0507QC
Rev. 06.01.23
*PUMP
MTR
1
2
*PUMP
MTR
1
2
PUMP
2
MTR
1
1/4" TOP TAB FOR EASY LINER REMOVAL
MATERIAL: WHITE SEMI GLOSS PAPER
INDIVIDUAL PIECES, SQUARE CORNERS WITH
BLACK COPY ON WHITE BACKGROUND
COLOR:
PUT UP:
ADHESIVE: PERMANENT
NOTE:
4 1/2"±1/16"
DANGER: ELECTRICAL SHOCK HAZARD. DISCONNECT ALL POWER BEFORE SERVICING.
HOT (POWER)
NOTE:
*INDICATES OPTIONAL ACCESSORIES
FIELD CONNECTIONS
SUGGEST HARD WIRED AS NORMAL MODE OF ATTACHMENT SUPPLIED BY OTHERS.
GROUND
NEUTRAL
WIRING DIAGRAM FOR 4414QC-230, 4420QC, 208/240V POWER PAKS
HOT (POWER)
ELECTRONIC TEMPERATURE
CONTROL
BLACK
COND. UNIT
SENSOR
ELECTRICAL
JUNCTION
CONTACTOR
RECEPTACLE
*BLM2000
1/4"±1/16"
10"±1/16"
FORM NO. 1008403
SUPPLY
SENSORSENSOR
Pb1
D.I.
180 FT.
3
540 FT.
9
10
10
600 FT.
570 FT.
360 FT.
6
8
9
8
7
7
450 FT.
510 FT.
480 FT.
420 FT.
390 FT.
5
6
5
4
4
270 FT.
330 FT.
300 FT.
240 FT.
210 FT.
Length
1
Coolant
2
3
2
1
90 FT.
150 FT.
120 FT.
60 FT.
30 FT.
(Gallons)
Trunk
For 2-12
Beverage Lines
For 16-24
Beverage Lines
6
18
20
19
12
15
17
16
14
13
9
11
10
8
7
1
3
5
4
2
COOLANT REQUIREMENTS
REVISIONS
REV ECO DESCRIPTION DESIGNER DATE APPROVED BY
D 2022-5777
UPDATE WIRING DIAGRAM TERMAINAL BLOCK, ADJUSTED
TOLERANCES
DPD 10/12/2022
DESCRIPTION
PART NUMBER
DRAWING NUMBER
MATERIAL:
REFERENCE:
SCALE: 1:1
1008403 1008403
WIRING DIAGRAM LABEL FOR 208-230V POWER PAKS
HOLES: .0135 THRU .125: .004
.1260 THRU .250: .005
.2510 THRU .500: .006
.5010 THRU .750: .008
.7510 THRU 1.000: .010
1.001 & UP: .012
BREAK SHARP EDGES - .015 X 45°
RADIUS SHARP FILLETS - .015 TO .031
DIMENSIONS ARE IN INCHES TOLERANCES:
UNLESS OTHERWISE SPECIFIED:
Ang =
Frac = 1/8
THIS DOCUMENT / PUBLICATION / SOFTWARE / DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORPORATION. IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING, RECORDING, OR USED IN ANY INFORMATION STORAGE, TRANSMISSION, OR RETRIEVAL SYSTEM, WITHOUT WRITTEN PERMISSION FROM THE PERLICK CORPORATION. COPYRIGHT 2015 PERLICK CORPORATION. ALL RIGHTS RESERVED.
Milwaukee, Wisconsin
Perlick Corporation
A A
B B
C C
D D
4
4
3
3
2
2
1
1
.X =
.XX =
.XXX =
OVERALL DIMENSIONS: 10 INCH X 4.75 INCH WEIGHT: LBS GAUGE: ga REQ QUAL MFG:
Wiring Diagram For 4420QC AC115 - 208/240, 60 HZ Power Paks
(4 Wire AC Power Source Required)
Wiring Diagram For 4404QC, 4410QC, 4414QC 115V Power Paks