Petsafe PBC00-15254 User manual

PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING
Rechargeable
Bark Control Collar
operating guide

2 Customer Care Center 1-800-732-2677
IMPORTANT SAFETY INFORMATION
Explanation of Attention Words and Symbols used in this guide
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey
all safety messages that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
CAUTION, used without the safety alert symbol, indicates a hazardous
situation which, if not avoided, could result in harm to your pet.
• Risk of explosion if battery is replaced by an incorrect type. Do not short circuit, mix old and
new batteries, dispose of in fire, or expose to water. When batteries are stored or disposed,
they must be protected from shorting. Dispose of used batteries properly.
• Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive
behavior. Aggressive dogs can cause severe injury or death to their owners and others. If
you are not sure that this product is right for your dog, please talk to your veterinarian or a
certified trainer.
The Bark Control Collar is not a toy. Keep it away from the reach of children. Use it only for its
bark stopping purpose.
Risk of skin damage. Please read and follow the instructions in this manual. Proper fit of the
collar is important. A collar worn for too long or made too tight on the pet’s neck may cause
skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as
bed sores.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the pet’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.

www.petsafe.net 3
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
• For additional information on bed sores and pressure necrosis, please visit our website.
These steps will help keep your pet comfortable and safe. Millions of pets are comfortable while
they wear stainless steel contacts. Some pets are sensitive to contact pressure. You may find
after some time that your pet is very tolerant of the collar. If so, you may relax some of these
precautions. It is important to continue daily checks of the contact area. If redness or sores are
found, discontinue use until the skin has fully healed.
The PetSafe®Rechargeable Bark Control Collar must be used only on healthy dogs. We
recommend that you take your dog to a veterinarian before using the collar if he is not in
good health.

4 Customer Care Center 1-800-732-2677
Thank you for choosing the PetSafe®brand. You and your pet deserve a companionship that
includes memorable moments and a shared understanding together. Our products and training
tools enhance the relationship between pets and their owners. If you have any questions about
our products or training your pet, please visit our website at www.petsafe.net or contact our
Customer Care Center at 1-800-732-2677.
To get the most protection out of your warranty, please register your product within 30 days
at www.petsafe.net. By registering and keeping your receipt, you will enjoy the product’s full
warranty and should you ever need to call the Customer Care Center, we will be able to help
you faster. Most importantly, PetSafe®brand will never give or sell your valuable information to
anyone. Complete warranty information is available online at www.petsafe.net.
Table of Contents
Components................................................................. 5
Features .................................................................... 5
How the Bark Control Collar Works ............................................... 5
Key Definitions ............................................................... 6
Charging the Bark Control Collar ................................................. 6
Fit the Bark Control Collar ...................................................... 7
Choose Between Three Bark Control Settings ...................................... 7
What to Expect During Use of the Bark Control Collar ................................ 9
Frequently Asked Questions......................................................... 10
Troubleshooting .................................................................... 10
Terms of Use and Limitation of Liability ........................................... 10
Customer Care International ................................................... 11
Battery Disposal ............................................................. 11
Perchlorate Battery........................................................... 11
Compliance ................................................................ 11
Warranty ................................................................... 12

www.petsafe.net 5
Components
Charging Adapter
Operating Guide
PetSafe®
Bark Control Collar
Features
• 10 Levels of progressive static correction
• Choose between 3 correction modes to fit your dog’s temperament
• Rechargeable battery and digital display
• Patented Perfect Bark™technology ensures your dog's bark is the only sound that will cause
the correction
• Waterproof
How the Bark Control Collar Works
The PetSafe®Rechargeable Bark Control Collar uses several features designed to shorten the
training phase and promote good behavior.
First, the Rechargeable Bark Control Collar has a unique patented sensor that provides
the most reliable bark detection available. The Bark Control Collar uses both vibration and
sound sensors (dual-detection) to discriminate each bark from other external noises. A static
correction is administered through the Contact Points only if both the vibration from the vocal
chords and the sound from the bark match the same criteria.

6 Customer Care Center 1-800-732-2677
Key Definitions
Digital Display: Displays the current
correction mode based on light
color(s) and the numeric indicator. Also
indicates the condition of the battery.
Settings Button: Adjusts the correction
mode and the level of correction your
dog receives when barking. Also used
to turn the Rechargeable Bark Control
Collar on and off.
Contact Points: Deliver the static correction.
Vibration Sensor Probe: Detects the vibrations of your dog’s barking.
Charging Jack: For connecting the charging adapter. Although the bark control unit is
waterproof, keep the cover in place when not charging to keep debris out of the opening.
Sound-Activated Sensor: Detects your dog’s bark.
Charging the Bark Control Collar
Before using the PetSafe®Rechargeable Bark Control Collar for the first time, be sure to charge the unit
by following the steps described below.
Follow these steps to charge the battery:
1. Lift the rubber cover protecting the Charging Jack.
2. Connect the charger connector to the Charging Jack.
3. Plug the charger into a standard wall outlet. The display light will flash the sequence Green-
Blue-Red to indicate that charging has started.
4. During charging, keep the Bark Control Collar in an open, well-ventilated area. The display
light will flash red twice every 10 seconds to indicate that charging is active.
5. When charging is complete, the charger will automatically shut off, preventing overcharging.
The display light will flash green twice every 10 seconds to indicate that charging is
complete. Note: The battery should fully charge in less than 4 hours.
6. Remove the charger from the Charging Jack. The light will flash the sequence Red-Blue-
Green to indicate the unit is no longer charging.
7. When charging is complete, replace the Charging Jack cover and unplug the battery charger.
The Rechargeable Bark Control Collar will automatically turn off when the battery charger is
connected. Following a charge, turn the unit back on before using.
Note: When the unit indicates that the battery is low (battery icon on the display indicates 1 bar
or less and/or the light flashes red 3 times every 5 seconds) it is time to recharge the unit. If the
battery pack is very low (i.e. been used too long or stored for an extended period of time) it may
take some time for the unit to indicate that charging has started. If the unit does not indicate
that it is charging after 1 hour, please contact our Customer Care Center.
Contact
Points
Vibration
Sensor Probe
Digital Display
Charging Jack
(charger attached)
Settings
Button
(Bottom)(Top)
Sound Activated Sensor

www.petsafe.net 7
Battery Life
Average battery life is 3 to 6 months, depending on how often your dog barks. However, due
to greater use during your dog’s training, your first battery charge may not last as long. To
conserve battery life, turn the Bark Control Collar off when not in use.
Fit the Bark Control Collar
Important: The proper fit and placement of your Bark Control Collar is
important for effective operation. The Contact Points must have direct
contact with your dog’s skin on the underside of his neck.
To assure a proper fit, please follow these steps:
1. Make sure the Bark Control unit is off.
2. Have your dog standing comfortably (A).
3. Place the Bark Control Collar on your dog’s neck close to
the ears. Center the Contact Points underneath your dog’s
neck, touching the skin (B).
Note: It is sometimes necessary to trim the hair around the
Contact Points to make sure that contact is consistent.
Do not shave the pet’s neck as this may
increase the risk of skin irritation.
4. Check the tightness of the Bark Control Collar by inserting
one finger between a Contact Point and the dog’s neck
(C). The fit should be snug but not constricting.
5. Allow your dog to wear the collar for several minutes, then
recheck the fit. Check the fit again as your dog becomes
more comfortable with the Bark Control Collar.
The Receiver Collar should not be worn for more than 12 hours out of every 24-hour
period. Leaving the collar on too long could lead to skin irritation.
Choose Between Three Bark Control Settings
The Rechargeable Bark Control Collar has three bark control settings that allow you to choose
how corrections are delivered. The modes are indicated on the digital display by light color(s)
and the numeric indicator.
1. The Temperament Learning mode tracks the number of corrections needed to substantially reduce
(and in most cases eliminate) the number of nuisance barks. The system provides 10 levels of static
correction. It begins with a low-level correction (Level 0). However, if excessive barking continues,
the correction intensity will increase with each successive bark (to a maximum of Level 9) until the
barking stops. This correction level becomes the starting level the next time the dog barks. Once
your dog has learned to reduce his barking, the initial warning corrections are automatically reduced.
A
B
C

8 Customer Care Center 1-800-732-2677
2. The Progressive Correction mode starts at the lowest level (Level 0) and progresses to the
next level (to a maximum of Level 9) each time your dog barks within 30 seconds of the
previous bark. If your dog does not bark again within 30 seconds, the correction level will
automatically reset to Level 0.
3. The User-Selected Correction mode allows you to manually select the correction level (0-9).
Note: In User-Selected mode, always start training at the lowest level of correction (Level 0).
Watch how your dog reacts, and if necessary, progress to the next correction level.
Note: As a built-in safety feature, if your dog barks 15 times or more within an 80 second period,
the Bark Control Collar will automatically shut off for 3 minutes. This safety feature is active in all
three modes of operation.
Temperament Learning Progressive Correction User-Selected Correction
Note: When the operating mode is changed, the correction level is automatically reset to Level 0.
The Rechargeable Bark Control has a single Settings Button that allows you to turn the unit on
and off, display or change the current correction mode, and change the correction level. The
following table describes how to perform the different tasks.
Task Steps to perform Indications
Turn the unit on Press and release the settings button
while the unit is off.
The light will flash green five times and
then display the current correction mode
as described on previous page.
Turn the unit off Press the settings button until the
display goes blank and the red light
appears. Release the button.
*
The light will flash red four times and the
unit will turn off.
Display current
correction mode
Press and hold the settings button
for less than 2 seconds before
releasing it.
The unit will display the current correction
mode and battery condition, as described
on previous page.
Green ligh
t
Blue light
Green ligh
t
Blue ligh
tNumber indicates
active correction leve
l

www.petsafe.net 9
Change active
correction mode
1. Press and hold the settings button
for at least 5 seconds.
• Mode will advance and be displayed
as described on previous page.
2. Continue to hold the settings
button to advance to the next
available mode.
• Every 2 seconds the mode will
advance and be displayed.
3. When the desired mode is
displayed, release the button.
• The selected mode will be displayed
during this time.
4. Once the button has been
released for 5 seconds, the new
correction mode will activate.
• The display will flash four times and
the unit will resume normal operation
using the new correction mode.
**
5. If the settings button is released
too early, simply press it again
within 5 seconds.
• The mode will advance and continue
as described in Step 2.
*If you continue to hold the settings button for more than 5 seconds, you will begin changing the
correction mode. You must release the settings button before attempting to turn off the unit.
** The light will flash every five seconds to indicate the current mode.
What to Expect During Use of the Bark Control Collar
Important: Do not leave your dog alone the first few times he receives a correction.
Place the Rechargeable Bark Control Collar properly on your dog and wait nearby until he barks.
Most dogs will understand very quickly that the Bark Control Collar is disrupting their urge to bark
and will relax and stop barking. Because the static correction from the Bark Control Collar may be
surprising or startling at first, some dogs may bark more at the initial correction.
On rare occasions, a dog may get into a bark-correction-bark-correction cycle. If this happens,
reassure your dog with calm, soothing tones. As your dog relaxes, he will understand that if he
becomes quiet, he will not receive any more static corrections. The small minority of dogs that
have this reaction will only have it the first time they wear the Bark Control Collar.
You should notice a reduction in your dog’s barking within the first couple of days that he wears
the Bark Control Collar. At this point, it is important to remember the learning process is still not
complete. Dogs will “test” this new learning experience and will increase their attempts to bark.
This usually occurs during the second week a dog wears the Bark Control Collar. If this does
occur, remain consistent and do not alter your use of the Bark Control Collar. You must place
the Bark Control Collar on your dog in every situation when you expect him to be quiet. If your
dog is not wearing the Bark Control Collar, he may resume barking and his learning would suffer
a setback.

10 Customer Care Center 1-800-732-2677
FREQUENTLY ASKED QUESTIONS
Will another dog’s bark set
off the Bark Control Collar?
No. It includes dual detection which eliminates false corrections.
Will the Bark Control Collar
work for my dog?
The Bark Control Collar is safe and effective for most breeds
and sizes of dogs. However, the Rechargeable Bark Control
Collar is recommended for dogs 40+ lbs.
Can I attach a leash to the
Bark Control Collar?
No. This can result in pulling the Contact Points too tightly
against your dog’s neck. Attach a leash to a separate, non-
metallic collar or a harness, making sure the extra collar does
not put pressure on the Contact Points.
TROUBLESHOOTING
My dog keeps barking
(does not respond to the
static correction).
• Tighten the Bark Control Collar and/or trim your dog’s
hair where the Contact Points touch his neck to ensure
good skin contact.
• Charge the battery.
• If your dog still does not respond, contact the Customer
Care Center.
The Display light(s) stopped
flashing.
• Ensure that the unit is turned on.
• Fully charge the battery.
• If the Display light(s) still do not flash, contact the
Customer Care Center.
Terms of Use and Limitation of Liability
1. Terms of Use
This Product is offered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this product implies acceptance of all such
terms, conditions, and notices.
2. Proper Use
This Product is designed for use with pets where training is desired. The specific temperament
or size/weight of your pet may not be suitable for this Product. Radio Systems®Corporation
recommends that this Product is not used if your pet is aggressive and accepts no liability for
determining suitability in individual cases. If you are unsure whether this Product is appropriate
for your pet, please consult your veterinarian or certified trainer prior to use. Proper use includes,
without limitation, reviewing the entire Operating Guide and any specific Caution statements.

www.petsafe.net 11
3. No Unlawful or Prohibited Use
This Product is designed for use with pets only. This pet training device is not intended to harm,
injure, or provoke. Using this product in a way that is not intended could result in violation of
Federal, State or local laws.
4. Limitation of Liability
In no event shall Radio Systems®Corporation be liable for any direct, indirect, punitive, incidental,
special or consequential damages, or any damages whatsoever arising out of or connected with the
use or misuse of this Product. Buyer assumes all risks and liability from the use of this Product.
5. Modification of Terms and Conditions
Radio Systems®Corporation reserves the right to change the terms, conditions and notices under
which this Product is offered.
Customer Care International
USA & Canada - Tel: [phone]
Monday - Friday 8 AM - 8 PM / Saturday 9 AM – 5 PM (EST)
Australia - Tel: [phone]
Monday - Friday 8:30 AM - 5 PM
New Zealand - Tel: [phone]
Monday - Friday 10:30 AM - 7 PM
Battery Disposal
Separate collection of spent batteries is required in many regions; check the regulations in
your area before discarding spent batteries. At the end of the product life, please contact our
Customer Care Center to receive instructions on proper disposal of the unit. Please do not
dispose of the unit in household or municipal waste. For a listing of Customer Care Center
telephone numbers in your area, visit our website at www.petsafe.net.
Perchlorate Battery
Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Compliance
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION: Modification or changes to this equipment not expressly approved by Radio
Systems®Corporation may void the user’s authority to operate the equipment.

12 Customer Care Center 1-800-732-2677
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a specific installation. If interference does occur to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult customer care, the dealer, or an experienced radio/TV technician for help.
Warranty
One Year Non-Transferrable Limited Warranty
This Product has the benefit of a limited manufacturer’s warranty. Complete details of the
warranty applicable to this Product and its terms can be found at www.petsafe.net.
Australia/New Zealand - In compliance with the Australian Consumer Law, Warranties Against
Defects, effective January 1, 2012, warranty details of this Product are as follows:
One Year Non-Transferrable Limited Warranty
What is covered: Radio Systems Australia Pty Ltd (hereinafter referred to as “Radio Systems”)
warrants to the original retail purchaser, and not any other purchaser or subsequent owner, that its
Product, when subject to normal and proper residential use, will be free from defects in material
or workmanship for a period of one (1) year from the purchase date. An “original retail consumer
purchaser” is a person or entity who originally purchases the Product, or a gift recipient of a new
Product that is unopened and in its original packaging. When serviced by Radio Systems Customer
Service, Radio Systems covers labor and parts for the first year of ownership; after the first year, a
service or upgrade charge will apply relative to replacement of the Product with new or refurbished
items at Radio System’s sole discretion.
The limited warranty is non-transferrable and shall automatically terminate if the original retail consumer
purchaser resells the Radio Systems Product or transfers the property on which the Radio Systems
Product is installed. This Limited Warranty excludes accidental damage due to dog chews; lightning
damage; or neglect, alteration, and misuse. Consumers who purchase Products outside of Australia,
New Zealand, or from an unauthorized dealer will need to return the Product to the original place of
purchase for any warranty issues.
Please note that Radio Systems does not provide refunds, replacements, or upgrades for change
of mind, or for any other reason outside of these Warranty terms.

www.petsafe.net 13
Claims Procedure:
Any claim made under this Warranty should be made directly to Radio Systems Australia Pty
Ltd Customer Care Centre at:
Radio Systems Australia Pty Ltd
PO Box 765, Mudgeeraba QLD 4213
Australia Residents: 1800 786 608
New Zealand Residents: 0800 543 054
Email: [email protected]
To file a claim, a proof of purchase must be provided. Without a proof of purchase, Radio
Systems will not repair or replace faulty components. Radio Systems requests the Consumer to
contact the Radio Systems Customer Care Centre to obtain a Warranty Return number, prior to
sending the Product. Failure to do so may delay in the repair or replacement of the Product.
If the Product is deemed to be faulty within 30 days from date of original purchase, Radio
Systems will organise for a replacement to be sent in advance of returning the faulty Product. A
Post Bag will be included with the replacement Product for the return of the faulty Product. The
Product must be returned within 7 days of receiving the replacement. If the Product is deemed
to be faulty after 30 days from the date of original purchase, the consumer will be required to
return the Product to Radio Systems at the consumer’s own expense. Radio Systems will test
and replace the faulty unit or its components and return to the consumer free of charge, provided
the Product is within its said warranty period. This warranty is in addition to other rights and
remedies available to you under the law. Radio Systems goods come with guarantees that cannot
be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Should you have any queries or require any further information, please contact our Customer
Care Centre on 1800 786 608 (Australia) or 0800 543 054 (New Zealand).

14 Customer Care Center 1-800-732-2677

www.petsafe.net 15

Radio Systems®Corporation
10427 PetSafe Way
Knoxville, TN 37932
1-800-732-2677
www.petsafe.net
400-1936
©2014 Radio Systems Corporation

DO NOT PRINT
THIS PAGE
Material: 100gsm Wood Free
Paper
Printing: Black
RSC Part #: 400-1936
MANUAL PBC00-15254
Description:
Created by: T King
Initial Creation Date: 11/08/2014
Approved by: L Taylor
Date Approved: 12/15/14
Program used: INDESIGN CC
Revision: 000 PRO: RSC11357
Revision Description: Initial Release to Production
Revision Date: N/A
Finishing: Die Cut, Fold,
2 Saddle Stitch, and Bulk Pack