Petsafe Big/Little Dog Remote Trainer Setup guide

2 1-800-732-2677
Thank you for choosing PetSafe®. Our mission is to ensure your pet’s safety by
providing you the tools and techniques to successfully train your pet. If you have
any questions, please contact the Customer Care Center at 1-800-732-2677 or
visit our website at www.petsafe.net.
____________________________________________________________________
Table of Contents
Components ...............................................................................................3
Other ItemsYou May Need..........................................................................3
How the System Works ................................................................................3
Key Definitions ...........................................................................................4
Operating Guide
Prepare the Remote Transmitter................................................................5
Prepare the Receiver Collar.......................................................................6
Fit the Receiver Collar ..............................................................................7
Find the Best Intensity Level for Your Pet ..................................................8
Understanding the Remote Transmitter .....................................................9
Training Guide
General Tips...........................................................................................10
Teaching Basic Obedience
The “Sit” Command............................................................................10
The “Come” Command.......................................................................11
The “Stay” Command .........................................................................12
Eliminating Unwanted Behavior
Jumping Up......................................................................................... 12
Digging ...............................................................................................13
Chasing...............................................................................................14
Trash Raiding ......................................................................................14
Excessive Barking ................................................................................15
Frequently Asked Questions ......................................................................16
Troubleshooting........................................................................................17
To Pair the Remote Transmitter and Receiver Collar...................................18
Test Light Instructions ..............................................................................18
Terms of Use and Limitation of Liability .................................................... 19
FCC .........................................................................................................19

www.petsafe.net 3
Components
Warranty
Card
Warranty
Receiver
Collar (Big Dog Shown)
Operating and
Training Guide
9-Volt Battery
Remote
Transmitter
Battery
(PetSafe® RFA-67)
Test Light
Tool
ID Tag Ring
Other Items You May Need
• Scissors
• Non-metallic collar and 10-foot leash
How the System Works
The PetSafe Remote Trainer has been proven safe, comfortable, and effective for all pets over 8
pounds.This system assists you in controlling your pet without a leash in a range up to 100 yards.
At the push of a button, the Remote Transmitter sends a signal, activating the Receiver Collar.
Using the Remote Trainer consistently and correctly, many misbehaviors that your pet exhibits can
be corrected or any basic obedience commands can be taught.

4 1-800-732-2677
Key Definitions
Remote Transmitter: Transmits the radio signal to the
Receiver Collar.
Intensity Level Dial: Provides a choice of 10 different
levels of stimulation to enable you to match the level to
your pet’s temperament.
Transmitter Indicator Light: Indicates when any
button on the Remote Transmitter is pressed. This light
also serves as a low battery indicator.
Tone Button: Sends an audible tone to your pet. There
is no stimulation associated with this button.
Stimulation Button: Delivers stimulation to your pet
through the Contact Points. When this button is held down
continuously for 8 seconds, the Remote Transmitter will
“time-out”, and you must release and press the button
again before any additional stimulation can be delivered to
your pet.
Remote Transmitter
Intensity
Level Dial
Transmitter
Indicator Light
Tone Button
Stimulation
Button
Intensity
Level
Receiver Collar: Receives the radio signal from the Remote Transmitter.
Receiver Indicator Light: Indicates when the Receiver Collar has been turned on or off. This
light also serves as a low battery indicator
Contact Points: Deliver stimulation to your pet.
.
Battery
Contact Points
Antenna
ON/OFF
Button
o
n
/
o
f
f
Receiver
Indicator
Light
Big Dog Receiver Collar
Receiver Collar
ON/OFF
Button
Antenna
Contact Points
Battery
o
n
/
o
f
f
Little Dog Receiver Collar
Receiver
Indicator
Light

www.petsafe.net 5
Operating Guide
Prepare the Remote Transmitter
To Insert and Remove the Battery
1. Hold the Remote Transmitter face down and pull the battery door open (1A, 1B).
2. Insert the 9-volt battery with the positive side oriented as shown (1C).
3. Replace the battery door by positioning the bottom edge (1D), and snap the battery
door into place.
+ --
+ --
1A 1B 1C 1D
Transmitter Indicator Light – Function and Response
Remote Transmitter Function Transmitter Indicator Light Response
Any button is pressed Solid in color
Low battery Flashes every 4 to 5 seconds
Step
1

6 1-800-732-2677
Prepare the Receiver Collar
To Insert and Remove the
Battery
Note: Do not install the battery while the
Receiver Collar is on your pet.
This Receiver Collar utilizes a
replaceable PetSafe®battery
(RFA-67).This unique battery is
designed to make battery replacement
easier and increase water protection.
To insert the battery, align the symbols
on the battery (arrow) and Receiver
Collar (triangle). Using the edge of
the Test Light Tool as shown, turn the
battery clockwise until the arrow lines
up with the lock symbol on the housing
(2A, 2B) .
To remove the battery, turn the battery
counter-clockwise using the edge of the
Test Light Tool as shown, (2C, 2D).
2A 2B
2D
2C
DO NOT attempt to cut into or pry open the battery. Be sure to discard the used
battery properly.
A replacement PetSafe®battery (RFA-67) can be found at many retailers. Contact the
Customer Care Center at 1-800-732-2677 or visit our web site at www.petsafe.net for
a list of common retailers.
Turning the Receiver Collar On and Off
To turn the Receiver Collar on, press and release the On/Off Button. The Receiver Indicator
Light will flash twice after the button is released, indicating the Receiver Collar is ready to
receive signals from the Remote Transmitter.
Once the Receiver Collar has been turned on, press the top button of the Remote Transmitter.
Upon pressing, the Receiver Collar should beep for as long as the top button is pressed. If it
does not, see “To Pair the Remote Transmitter and the Receiver Collar” in the Troubleshooting
section.
To turn the Receiver Collar off, press and release the On/Off Button. The Receiver Indicator
Light will flash three times after the button is released, indicating the unit has been turned off.
Note:To extend the life of the batteries, turn the Receiver Collar off when it is not in use.
Important: If the Receiver Collar is left on continuously, the maximum battery life
(before replacing batteries) will be two weeks.
Step
2

www.petsafe.net 7
Receiver Indicator Light – Function and Response
Receiver Collar Function Receiver Indicator Light Response
Turning on Flashes two times
Turning off Flashes three times
Low battery Flashes every 4 to 5 seconds
_____________________________________________________________
Fit the Receiver Collar
Important: The proper fit and placement of your Receiver Collar is important for
effective operation. The Contact Points must have direct contact with your dog’s
skin on the underside of his neck.
To assure a proper fit, please follow these steps:
1. Make sure that the battery is not installed in the Receiver
Collar.
2. Have your dog standing comfortably (3A) .
3. Center the Contact Points underneath your dog’s neck,
touching the skin (3B).
YES
NO
3A
Note: It is sometimes necessary to trim the hair
around the Contact Points to make sure that
contact is consistent.
3B
4.The PetSafe QuickFit™ Collar
is designed so you can quickly
attach and remove the Receiver
Collar from your dog while
maintaining the desired fit.
a.With the Snap Buckle
fastened (3C) , thread the
collar through the Metal
Buckle (3D).
b. Slide the excess collar
through the “C” Loop on top of the Snap Buckle (3E) .
This will hold the collar in place.
c. Once the collar fit is determined, simply use the Snap
Buckle to remove and replace the collar.
Step
3
Snap Buckle “C” Loop
Metal Buckle
3C 3D
3E

8 1-800-732-2677
5.The Receiver Collar should fit snugly, yet loose enough to allow one
finger to fit under the strap (3F). Allow your dog to wear the collar
for several minutes, then recheck the fit. Check the fit again as your
dog becomes more comfortable with the Receiver Collar.
6.Trim the collar as follows:
a. Mark the desired length of the collar with a pen. Allow for
growth if your dog is young or grows a thick winter coat.
b. Remove the Receiver Collar from your dog and cut off excess.
ID Tag Ring
Use the ID Tag Ring to attach your
dog’s ID tags to the collar. Simply
place the ID Tag Ring through one
of the holes on your collar. Make
sure to place the Ring far enough
from receiver housing so that tags
will not hit the Receiver or the
Contact Points (3G).
Important: Do not attach a leash to the collar. This can result in pulling the Contact
Points too tightly against your pet’s neck. Attach a leash to a separate, non-metallic
collar or harness, making sure the extra collar does not put pressure on the Contact
Points.
_____________________________________________________________
Care and Cleaning
For comfort, safety, and effectiveness of this product, please ensure that you check the
fit of your pet’s collar frequently. This Guide describes proper collar fitting. If any skin
irritation is observed, discontinue the use of the collar for a few days. If the condition
persists beyond 48 hours, see your veterinarian.
To prevent skin irritation from occurring:
• The Receiver Collar should not be worn for more than 8 hours out of every 24-hour
period.
•Your pet’s neck and the Contact Points must be washed weekly with a washcloth and
mild hand soap, then rinsed thoroughly.
• Be sure that your pet’s neck is thoroughly dry before placing the Receiver Collar back
on his neck.
3F
3G

www.petsafe.net 9
Find the Best Intensity Level for Your Pet
The Remote Trainer has ten (10) different Intensity Levels. This allows you to choose
the stimulation that is best for your pet.
Note: Always start at the lowest level and work your way up.
Once you have placed the Receiver Collar on your pet, it is time to find the Intensity
Level that is best for your him.This is called the Recognition Level.
A slight change in your pet’s behavior, such as looking around in curiosity, scratching at
his collar, or flicking his ears, indicates the Recognition Level that is best for him.
Follow the steps below to find your pet’s Recognition Level:
1. Press the Tone Button for 2 to 3 seconds. If your pet reacts to this, you may use this
button for training. If your pet shows no reaction, go to the next step.
2. Starting at Level 1, press the Stimulation Button continuously for 2 to 3 seconds.
3. If your pet shows no reaction, go to the next Intensity Level and repeat the process.
4. Repeat each Intensity Level several times before moving to the next level.
5.YOUR PET SHOULD NOT VOCALIZE OR PANIC. IF THIS HAPPENS, GO
BACK TO THE PREVIOUS LEVEL AND REPEAT THE PROCESS.
6. If your pet continues to show no response at Level 10, check the fit of the Receiver
Collar.
If all of these steps have been done and your pet continues to show no reaction to the
stimulation, contact the Customer Care Center at 1-800-732-2677.
_____________________________________________________________
Understanding the Remote Transmitter
To train using the Tone Button:
The audible sound emitted by the Receiver Collar can be just as effective as the
stimulation for some dogs. The Transmitter Indicator Light will glow for as long as
this button is pressed.To use this button for training, simply substitute “Tone Button”
whenever “Stimulation Button” is used in the Training Guide section.
To train using the Stimulation Button:
You control the timing of the stimulation being applied to your pet. The stimulation
stays on as long as the Stimulation Button is pressed. If this button is pressed longer
than 8 seconds, the Remote Transmitter will “time-out,” the Transmitter Indicator Light
will turn off, and stimulation will no longer be delivered to your pet. This is a safety
feature in the Remote Transmitter. If the Remote Transmitter times out, release the
Stimulation Button and press it again to deliver stimulation.
Note: For either one or both of these training methods to be effective, they must be used
consistently along with the command you are trying to teach your pet.
Step
4

10 1-800-732-2677
Training Guide
General Tips
• Eliminate one misbehavior or teach one obedience command at a time. If you move too fast with
the training, your pet may become confused.
• Be consistent. Give your pet a tone or stimulation with each misbehavior.
• Do not over-correct your pet. Use as few stimulations as possible to train your pet.
• Unless you can supervise him, it is recommended that you restrict your pet from situations in
which he has a history of misbehaving. However, setting up a situation as a training session can
dramatically improve your chances of success.
• If your pet reacts to the training by hiding or acting fearful, redirect his attention to a simple and
appropriate behavior such as the “Sit” command.
• Never use the Remote Trainer to correct or eliminate any form of aggressive behavior. If you are
unsure if your dog is aggressive, please consult your veterinarian or a certified trainer.
____________________________________________________________________
Teaching Basic Obedience
The “Sit” Command
1. Put a separate, non-metallic collar on your pet’s neck ABOVE the Receiver Collar, and attach a
10-foot leash. Note: Be sure the extra collar does not put pressure on the Contact Points.
2. Hold the leash and the Remote Transmitter in one hand. Keep your other hand free to guide
your pet into a “Sit” position.
3. Press and hold the Stimulation Button.
4. Immediately give the “Sit” command while continuing to hold the Stimulation Button.
5. Release the Stimulation Button as soon as your pet is in position, and praise him.
6. Release your pet from the “Sit” command and play.
7. Repeat Steps 2 through 6.
Note: If your pet breaks the “Sit” command, repeat steps 3 through 6. Keep your pet close to you while
teaching the “Sit” command.