Philio Technology Corporation PAN38 User manual

Smart energy plug PAN38
This plug-in ON/OFF switch PAN38 is a security enabled wireless switch, based on Z-
ave Plus technology. Z- ave PlusTM enabled devices displaying the Z- ave PlusTM
logo can also be used with it regardless of the manufacturer, and can also be used in
other manufacturer’s Z- aveTM enabled networks. Remote On/Off control of the con-
nected load is possible with another manufacturer’s wireless Controller. Each switch is
designed to act as a repeater. Repeaters will re-transmit the RF signal to ensure that the
signal is received by its intended destination by routing the signal around obstacles and
radio dead spots. Because PAN38 supports Security Command Class, it can learn with
Secured controller. Its functionality and supported command classes are identical when
included as a secure and non-secure device.
This plug-in ON/OFF switch is able to detect instance wattage (3000 /230VAC/13A)
and overload current (14.5A with resistive load) of connected lights or appliances. hen
detecting overload state, the Switch will be disabled and it’s On/Off button will be lock-
out of which LED will flash quickly. However, unplug and reconnect the switch will re-
set its overload condition to normal status.
Specification
Operating Voltage 100V-240V~ 50Hz-60Hz
Maximum Load (Ampere) 13A (Resistive load) PAN38-1; PAN38-2; PAN38-3
Maximum Load (Ampere) 10A (Resistive load) PAN38-4 (Switzerland)
Socket Type:
Germany type: PAN38-1
France type: PAN38-2
UK type: PAN38-3
Switzerland type: PAN38-4
Range Minimum 40 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
Frequency Range 868.40MHz & 869.85MHz/ EU (PAN38-1/-2/-3/-4);
RF Maximum Power +10dBm (Peak), -10dBm (Average)
** Specifications are subject to change and improvement without notice.
Troubleshooting
Symptom Cause of Failure Recommendation
The Switch not working
and LED off
1.The Switch is not plugged into
the electrical outlet properly
2.The Switch break down
1. Check power connections
2. Don’t open up the Switch
and send it for repair.
The Switch LED illumi-
nating, but cannot control
the Switch of the load at-
tached
1.Check if the load plugged into
the Switch has its own ON/OFF
switch
2. The switch is protected
1. Set the ON/OFF switch of
the load attached to ON
2. Unprotected the switch or
follow the instruction of pro-
tection.
The Switch LED illumi-
nating, but the Detector
cannot control the Switch
1. Not carry out association
2. Same frequency interference
1. Carry out association
2. ait for a while to re-try
LED keep flashing, but
cannot control Overload occurs
Remove the load attached or
check max. load cannot ex-
ceed 13A (Resistive load)

For Instruction to http //www.philio-tech.com
DANGER
Danger of electrocution!
All works on the device may be performed only by a qualified and licensed elec-
trician. Observe national regulations.
Any works introducing changes into the configuration must be always per-
formed with disconnected voltage.
Choosing a Suitable Location
1. Do not locate the Module facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Module is 0°C~40°C.
3. Do not locate the Module where exists combustible substances or any
source of heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Module will become a little bit hot of
which phenomenon is normal.
Warning:
1.Plug out to disconnect from power supply; Do not plug in line.
2. Do not exceed the max rating.
Warnung:
1.Trennen Sie das Gerät on der Stromzuführung. Verwenden Sie das Gerät nicht mit
einem DIP Schalter.
2. Achten Sie darauf, dass die maximale Spannung niemals überschritten wird.
Warnung:
für zwischenstecker:
nicht hintereinander stecken
Socket Type
Since the socket type for each country in Europe aries, refer to the outline for each
socket suited for each country as follows:
PAN38-1 German PAN38-2 French PAN38-3 U.K.
Note: Please make sure that the intensity of the plug of the electrical de ice must be 16A
and ha e same head as the enclosed plug before inserting to the socket.

Adding to Z-WaveTM Network
In the front casing, there is an On/Off button with LED indicator which is used to
toggle switch on and off or carry out inclusion, exclusion, reset or association.
hen first power is applied, its LED flashes on and off alternately and repeatedly
at 0.5 second intervals. It implies that it has not been assigned a node ID and start
auto inclusion.
Auto Inclusion
The function of auto inclusion will be executed as long as the switch does not
have Node ID and just plug the switch into a wall outlet.
Note Auto inclusion timeout is 2 minutes; during which the node information of
explorer frame will be emitted once several seconds. Unlike “inclusion” function
as shown in the table below, the execution of auto inclusion is free from pressing
the On/Off button on the Switch.
The table below lists an operation summary of basic Z- ave functions. Please re-
fer to the instructions for your Z- aveTM Certificated Primary Controller to ac-
cess the Setup function, and to Add/Remove/Associate devices
Function Description Annotation
No node ID The Z- ave Controller does not al-
locate a node ID to the Switch.
LED 2-second on, 2-second
off
Add 1. Put your Z- ave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
2. Pressing On/Off button three
times within 2 seconds will enter
inclusion mode.
Remove 1. Put your Z- ave controller into
exclusion mode by following the
instructions provided by the
controller manufacturer.
2. Pressing On/Off button three
times within 2 seconds will enter
exclusion mode.
3.Node ID has been excluded. LED 2s On, 2s Off (Enter
auto inclusion)
Reset 1. Pressing On/Off button three
times within 2 seconds will enter
inclusion mode.
Use this procedure only in
the event that the primary
controller is lost or other-
wise inoperable.
2. ithin 1 second, press On/Off
button again for 5 seconds.
3. IDs are excluded. LED 2s On, 2s Off (Enter
auto inclusion)
Association 1. The PAN38 is an always listen-
ing Z- ave device, so associa-
tions may be added or removed
by a controller at any time. Or If
your controller requires to have
the PAN38 send a 'node infor-
mation frame or NIF for associa-
tions, then pressing the On/Off
button three times within 2 sec-
onds will cause the PAN38 to
send its NIF.

2. There is only one group for the
switch
Including a node ID allocated by Z- ave Controller means inclusion. Excluding a
node
ID allocated by Z- ave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the Z-
ave Controller.
LED Indication
To distinguish what mode the switch is in, view from the LED for identification. The color of
LED could be blue、cyan、green、orange、pink or red, it represents the power consumption from
light to heavy.
State Type LED Indication
Normal Under normal operation, toggle On/Off button between On and Off. hen
pressing On, LED lights up, whereas Off, LED is off.
No node ID Under normal operation, when the Switch has not been allocated a node ID,
the LED flashes on and off alternately at 2-second intervals. By pressing
On/Off button, it will stop flashing temporarily.
Learning hen PAN38 is in learning mode, LED flashes on and off alternately and
repeatedly at 0.5 second intervals.
Overload hen overload state occurs, the Switch is disabled of which LED flashes on
and off alternately at 0.2 second intervals. Overload state can be cleared by
unplugging and reconnecting the Switch to the wall outlet.
Choosing a Suitable Location
1. Do not locate the Switch facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Switch is 0°C~40°C.
3. Do not locate the Switch where exists combustible substances or any source
of heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Switch will become a little bit hot of
which phenomenon is normal.
Installation
1. Plug this On/Off Switch into a wall outlet near the load to be controlled.
2. Plug the load into the Switch. Make sure the load to be controlled cannot
exceed 13A.
3. Press the button or switch on the load to the ON position.
4. To manually turn ON the Switch, press and release the On/Off button. The
LED will turn ON, and the load plugged into the Switch will also turn ON.
5. To manually turn OFF the Switch, simply press and release the On/Off but-
ton. The LED will turn OFF and the load plugged into the Switch will also
turn OFF.
Programming
1. Basic Command Class / Binary Switch Command Class
The Switch will respond to BASIC and BINARY commands that are part of
the Z- ave system.
1-1 BASIC_GET / BINARY_S ITCH_GET
Upon receipt of the following commands from a Z- ave Controller, the
Switch will report its On/Off state to the node asked.
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]
Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]

Binary Switch Report Command:
Report OFF:[Command Class Switch Binary, Switch Binary Report,
Value =0(0x00)]
Report ON:[Command Class Switch Binary, Switch Binary Report,
Value = 255(0xFF)]
1-2 BASIC_SET / S ITCH_BINARY_SET
Upon receipt of the following commands from a Z- ave Controller, the load
attached to the Switch will turn on or off.
[Command Class Basic, Basic Set, Value = 1~99,255(0xFF)]: the load
attached to the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached
to the Switch turns off.
[Command Class Switch Binary, Switch Binary Set, Value = 1~99,
(255)0xFF]: the load attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]:
the load attached to the Switch turns off.
2. Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to associated Z- ave devices. It supports
one association group with one node support for Grouping 1. For group 1, the
Switch will report its latest status to Z- ave Controller.
Grouping 1 includes, S ITCH_BINARY_REPORT, METER_REPORT,
ALARM_REPORT.
2-1 Auto report to Grouping 1 (Maximum Node 5)
2-1-1 On/Off Event Report
hen “on” or “off” state has been changed, it will send Binary Switch Report
to the node of Grouping 1.
Binary Switch Report
ON: [Command Class Switch Binary, Switch Binary Report, Value
=255(0xFF)]
OFF: [Command Class Switch Binary, Switch Binary Report, Value
=0(0x00)]
2-1-2 Instant Power Consumption vary over 5% report
hen the power consumption of load varies over 5%, it will send Meter report
to the nodes of Grouping 1.
Meter Report Command:
[Command Class Meter ，Meter Report ，Rate Type = 0x01 ，Meter
Type = 0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
2-1-3 Overload alarm report
hen PAN38 detects the current is more than 14.5A, it will send Alarm Report
to Group 1 node.
The content of Alarm Report
Alarm report command:
[Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08, Alarm
Level = 0xFF]
2-2 Response to Meter Get Command
The Switch will report its (1) instant Power Consumption ( att) or (2) accumu-
lated power consumption (K H) or (3) AC load Voltage (V) or (4) AC load
current (I) (5) load power factor (PF) to Z- ave Controller after receive the
Meter Get Command from Z- ave Controller.
2-2-1 Instant Power Consumption ( att) of Switch
hen receiving Meter Get Command, it will report Meter Report Command to
the node.

Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x02(W)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter
Type =
0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]
Example:
Meter Value 1 = 0x00 ( )
Meter Value 2 = 0x00 ( )
Meter Value 3 = 0x03 ( )
Meter Value 4 = 0xEA ( )
Meter( ) = Meter Value 3 *256 + Meter Value 4 = 100.2
2-2-2 Accumulated Power Consumption (K h)
hen receiving Meter Get Command, it will report Meter Report Command to
the node.
Meter Get Command:
[Command Class Meter, Meter Get, Scale = 0x00 KWh)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01 ，Meter
Type = 0x01，
Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]
Example:
Scale = 0x00 (K h)
Precision = 2
Size = 4 Bytes (K h)
Meter Value 1 = 0x00(K h)
Meter Value 2 = 0x01(K h)
Meter Value 3 = 0x38(K h)
Meter Value 4 = 0xA3(K h)
Accumulated power consumption (K h) = (Meter Value 2*65536) + (Meter
Value 3*256) + (Meter Value 4) = 800.35 (K h)
2-2-3 Clearing accumulated power consumption
henever re-start counting the accumulated power consumption is needed, you
can use Meter Reset Command to clear it.
Meter Reset Command: [Command Class Meter, Meter Reset]
2-2-4 AC load Voltage (V)
hen receiving Meter Get Command, it will report Meter Report Command to
the node.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x04(V)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter
Type = 0x01 ，Precision = 1 ，Scale = 0x04 ，Size = 2 ，Meter
Value(V)]
Example:
Scale = 0x04 (V)
Precision = 1
Size = 2 (2 Bytes of V)
Meter Value 1 = 0x09(V)
Meter Value 2 = 0x01(V)
AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)
2-2-5 AC load current ( I )
hen receiving Meter Get Command, it will report Meter Report Command to
the node.
Meter Get Command:
[Command Class Meter, Meter Get, Scale =0x05(I)]
Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type
= 0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I)]
Example:
Scale = 0x05 (I)
Precision = 2
Size = 2 (2 Bytes of I)
Meter Value 1 = 0x01(I)
Meter Value 2 = 0x21(I)
AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)
2-2-6 load power factor (PF)
hen receiving Meter Get Command, it will report Meter Report Command to
the node.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x06(PF)]
Meter Report Command:
[Command Class Meter ，Meter Report，Rate Type = 0x01 ，Meter
Type = 0x01 ，Precision = 2，Scale = 0x06 ，Size = 1 Bytes ，Meter
Value(PF)]
Example:
Scale = 0x06 (PF)
Precision = 2
Size = 1 (1 Byte of PF)
Meter Value 1 = 0x63(PF) (It means that the load power factor is 0.99)
3. Z-Wave’s Configuration
Configuration
Parameter Function Size (Byte) Value Unit Default Description
1 att Meter 2 0x0000 5s 720 0: Disable att
Report Period -
0x7FFF
Report
1~32767: 5s~ 45h
2
K H Meter
Report Period 2
0x0000
-
0x7FFF
10min 6
0: Disable K h
Report
1~32767:
10min~ 227days
3
Threshold of
current for Load
caution
2 10-1300 0.01A 1300 1300*0.01A
= 13A
4
Threshold of
K h for Load
caution
2 1-10000 1K h 10000 10000*1K h
= 10000 K h
5Restore switch
state mode
1 0-2 1 0: Switch off
1: Last switch state
2: Switch on
6Mode of Switch
Off function 1 0-1 1 0: Disable 1: Enable
7LED indication
mode
1 1-3 1 1: Show switch state
2: Show night mode
3: One flash mode
8att differential
mode 1 0-4 1
0 : Disable
1 : 5%
2: 10%
3: 15%
4: 10%
9Switch status
report mode 1 0-1 1 0: Disable 1:Enable
3-1 att Meter Report Period:
If the setting is configured for 1hour (set value =720), PAN38 will report its

instant power consumption to Group1 node every 1 hour. The maximum inter-
val to report its instant power consumption is 45 hours
(5s*32767/3600=45hr). hen the setting is 0, PAN38 will disable att auto
report function. The default value is 720.
3-2 K H Meter Report Period:
If the setting is configured for 1hour (set value =6), PAN38 will report its Ac-
cumulated Power Consumption (K h) to Group1 node every 1 hour. The
maximum interval to report its Accumulated Power Consumption (K h) is
227.55 days (10min*32767/1440=227.55 days). hen the setting is 0, PAN38
will disable K H auto report function. The default value is 6.
3-3 Threshold of current for Load Caution
This is a warning when the current of load over the preset threshold value, if
the setting value is 1300, when the load current of Relay1 over this value,
PAN38 will send current meter report to warn the Group1 node, the range of
the setting value is from 10 to 1300, and the default value is 1300.
3-4 Threshold of K h for Load Caution
This is a warning when the K h of load over the preset threshold value, If the
setting value is 10000, when the Accumulated Power Consumption of Relay1
over this value, PAN38 will send K H meter report to warn the Group1
node, minimum value is 1K h and default value is 10000 k h.
3-5 Restore switch state mode:
henever the AC power return from lost, PAN38 will restore the switch state
which could be S ITCH OFF、LAST S ITCH STATE、S ITCH ON. The
default setting is LAST S ITCH STATE.
3-6 Mode of switch off function:
hen the mode of switch On/Off is set to 0, any command of switch off will be
disabled and the On/Off function of include button will be disabled. The default
setting is enable mode. hen manual On/Off function is disabled, the RF com-
mand can only switch On but not Off. This is useful function for keeping the de-
vice in switch on state.
3-7 LED indication mode: The default setting is Show Switch State.
3-7-1 Show Switch State：hen switch is on, LED is on. hen switch is off,
LED is off.
3-7-2 Show Night mode：hen switch is on, LED is off. hen switch is off,
LED is on.
3-7-3 One Flash mode ：hen the state of switch changes, LED will be on
only one second, then LED keeps off.
3-8 att differential mode：The default setting is 1 (= 5%).
henever att value of PAN38 changes over 5% of last reading value, it will
send Meter report to the group 1 nodes. However, if att differential mode as
0, the unsolicited report will be disabled.
3-9 Switch status report mode: The default setting is 1(Enable)
henever PAN38 manually switch on or off, it will send BINARY_S ITCH_
REPORT to the node of group1, disable when this config set to 0.
4. Firmware update over the air (OTA)
PAN38 is based on 700 series SoC and supports Firmware Update Command
Class, it can receive the updated firmware image sent by controller via the Z-
wave RF media. It is a helpful and convenient way to improve some function if
needed.
5. The Switch supports Command Classes including…
Command Class Version Required Security Class
Z- ave Plus Info 2 None
Security 0 1 None
Security 2 1 None
Supervision 1 None
Transport Service 2 None

Association 2 Highest granted Security Class
Association Group
Information 3Highest granted Security Class
Basic 2 Highest granted Security Class
Binary Switch 2 Highest granted Security Class
Configuration 4 Highest granted Security Class
Device Reset Locally 1 Highest granted Security Class
Firmware Update Meta Data 5 Highest granted Security Class
Indicator 3 Highest granted Security Class
Manufacturer Specific 2 Highest granted Security Class
Meter 5 Highest granted Security Class
Multi Channel Association 3 Highest granted Security Class
Notification 8 Highest granted Security Class
Powerlevel 1 Highest granted Security Class
Version 3 Highest granted Security Class
Socket Type
Since the socket type for each country in Europe varies, refer to the outline for
each socket suited for each country as follows:
Germany type PAN38-1
France type PAN38-2
UK type PAN38-3
Switzerland type PAN38-4
Note: Please make sure that the intensity of the plug of the electrical device must
be 16A and have same head as the enclosed plug before inserting to the socket.

Disposal
This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent possi-
ble harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environ-
mental safe recycling.
Company of License Holder：Philio Technology Corporation
Address of License Holder：8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist.,
New Taipei City 24257, Taiwan(R.O.C)
www.philio-tech.com
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications.
However, there is no guarantee that interference will not occur in a particular in-
stallation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party respon-
sible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other an-
tenna or transmitter.