Philio Technology Corporation PST09-A User manual

4 in 1 Multi Sensor
PST09 -A/B/C/D (Zigbee)
The 4 in 1 multi-sensor PST09 has PIR, door/window, temperature,
and light sensor for com ining several functionalities in one device,
ased on Zig ee 3.0 technology. ZigBee is the only open, glo al
wireless standard to provide the foundation for the Internet of Things
y ena ling simple and smart o jects to work together, improving
comfort and efficiency in everyday life.
Warning
lost network will cause the battery to continue to consume
power.
When the device power on, the device will check is it already adding to
the network? If does, ut can't handshake, the device will try to link
with zig ee network every minute. After 6 times, the device LED will
flash in every second and continue 30 seconds.
The cycle will not stop until join the network.
This will cause the attery to continue to consume power.
Function Compare A/B/C/D
PIR Door/Window Temperature Light sensor
PST09-A V V V V
PST09-B V V V
PST09-C V V V
PST09-D V
Specification
Rated DC3V (CR123A)
RF distance Min. 40M indoor,
100M outdoor line of sight,
RF Frequency 2405-2480MHz (16 channels)
(EU/US/CSA/TW/JP)
RF Maximum Power +8dBm
Function PIR, door/window, temperature
and light sensor
Dimension 24.9 x 81.4 x 23.1mm
25.2 x 7.5 x 7 mm (magnetic)
Weight
Location indoor use only
Operation temperature -20
o
C ~ 50
o
C
Humidity 85%RH max
Marking CE
Specifications are su ject to change and improvement
without notice.
1

For Instruction to http:// www.philio-tech.com
Overview
Add to/Reset to default from Zigbee Network
There are two tamper keys in the device, one is in the ack side,
another is in the device. They have the same function. Both of them
can joining network, reset from Zig ee network.
In the first time, add the device into the Zig ee network. First, make
sure the primary controller is in the inclusion mode. And then power on
the device, Pressing tamper key three times within 1.5 seconds will
enter inclusion mode. The device will auto start the try joining network
mode. And it should e included in 120 seconds. You will see the LED
light ON one second.
* Joining network
1. Have Zig ee Controller entered inclusion mode.
2. Pressing tamper key three times within 1.5 seconds will enter
inclusion mode.
* Reset to default
1. Pressing tamper key four times within 1.5 seconds and do not
release the tamper key in the 4
th
pressed, and the LED will turn
ON.
2. After 3 seconds the LED will turn OFF, after that within 2
seconds, release the tamper key. If successful, the LED will light
ON one second. Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to factory default.
Zigbee IAS-ZONE
While the device is associated with a Zig ee network:
•The PST09 will try to find the CIE.
•When PIR was triggered or door/window sensor was triggered.
PST09 will send “ZCL Zone State Change Notification” to CIE.
2

Zigbee Message Report
* Motion Report
When the PIR motion detected, the device will unsolicited to send the
“Zone Status Change Notification” to the CIE.
Cluster ID : 0x0500
Zone Type: Motion (0x000D)
Zone State : 0x0001 (see Ta le1 it0 = 1)
* Motion off Report
When the PIR motion detected, After 30 seconds the device will
unsolicited to send the “Zone Status Change Notification” to the CIE.
Cluster ID : 0x0500
Zone Type: Motion (0x000D)
Zone State : 0x0000 (see Ta le1 it0 = 0)
* Door/Window Report
When the Door/Window state changed, the device will unsolicited to
send the “Zone Status Change Notification” to the CIE.
Cluster ID : 0x0500
Zone Type: Door/Window (0x0015)
Zone State :
OPEN : 0x0001 (see Ta le1 it0 = 1)
CLOSE : 0x0000 (see Ta le 1 it0 = 0)
* Tamper Report
When the 2 tamper keys in the device are pressed over 5 seconds. The
device will into the alarm state. In that state, if any one of the tamper
keys e released, the device will unsolicited to send the “Zone Status
Change Notification” to the CIE.
Cluster ID : 0x0500
Zone State : 0x0004 (see Ta le1 it2 = 1)
* Temperature Report
When the temperature differential over 0.5 Celsius, the device will
unsolicited to send the “Zone Status Change Notification” to the CIE.
Cluster ID : 0x0402
Attri ute ID : 0x0000
Endpoint : 0x03
DataType : 29
* Illumination Report
When the illumination defferential over 5 percent, the device will
unsolicited to send the “Zone Status Change Notification” to the CIE.
Cluster ID : 0x0400
Attri ute ID : 0x0000
Endpoint : 0x04
DataType : 21
* Timing Report
Beside the event triggered could report message, the device also
support the timing unsolicited report of the status.
•Low attery report:
When the attery level is too low, every 30 minutes will report
once.
3

Cluster ID : 0x0500
Zone State : 0x0008 (see Ta le1 it3 = 1)
•Set temperature auto report:
The time setting ranges from 1 to 255 minutes. The shortest
setting could e 60 seconds, equal to 1 minute, the longest one
could e 15300 seconds, equal to 255 minutes. Please set it with
60pcs.
Cluster ID : 0x0402
Attri ute ID : 0x0000
Endpoint : 0x03
DataType : 29
minReportTime : 0x0001 (seconds etween reports )
0xFFFF (stop report)
maxReportTime : 0x0001 (seconds etween reports )
0xFFFF (stop report)
•Set illumination auto report:
The time setting ranges from 1 to 255 minutes. The shortest
setting could e 60 seconds, equal to 1 minute, the longest one
could e 15300 seconds, equal to 255 minutes. Please set it with
60pcs.
Cluster ID : 0x0400
Attri ute ID : 0x0000
Endpoint : 0x04
DataType : 21
minReportTime : 0x0001 (seconds etween reports )
0xFFFF (stop report)
maxReportTime : 0x0001 (seconds etween reports )
0xFFFF (stop report)
Notice1 “Zone State” change as PIR triggered 、door/window
triggered or low attery. (see Ta le1)
Notice2 If device have motion sensor, will send “Endpoint” is 0x01
message. If device have door/window sensor, will send “Endpoint” is
0x02 message. And then if device have motion sensor and
door/window sensor, will send “Endpoint” is 0x01 message and
“Endpoint” is 0x02 message in all message report.
Attribute Bit
Number
Meaning Values
0Alarm1 1 – opened or alarmed
0 – closed or not alarmed
1Alarm2 1 – opened or alarmed
0 – closed or not alarmed
2Tamper 1 – Tampered
0 – Not tampered
3Battery 1 – Low battery
0 – Battery OK
4Supervision reports
Note 1)
1 – Reports
0 – Does not report
5Restore reports
Note 2)
1 – Reports restore
0 – Does not report restore
6Trouble 1 – Trouble/Failure
0 – OK
7AC mains) 1 – AC/Mains fault
0 – AC/Mains OK
8-15 Reserved -
Ta le 1 Zone Status Value
Power Up Procedure
4

* Battery Power Check
When the power up, the device will detect the power level of the
attery immediately. If the power level is too low, the LED will continue
flash a out 5 seconds. Please change another new attery.
* Network State Check
When the power on, the device will check the network state. If the
device join network , the LED will steady off. If doesn't, The LED will
flash in every second and continue 120 seconds.
* PIR Warm Up
When the power on, the PIR need to warm up efore operation. The
warm up time a out 1 minute, the LED will flash in every 2 seconds.
After finish the procedure the LED will light ON three times.
* Try joining network
When the power on, the device will check is it already adding to the
network? If doesn't, it will auto start the joining network mode. Until
timeout or the device joined network.
* lost network
When the device power on, the device will check is it already adding to
the network?
If does, ut can't handshake, the device will try to link with zig ee
network every minute.
After 6 times, the device LED will flash in every second and continue 30
seconds.
The cycle will not stop until join the network.
This will cause the attery to continue to consume power.
Over The Air (OTA) Firmware Update
The device support the Zig ee firmware update via OTA.
Before starting the procedure, please remove the front cover of the
device. Otherwise the hardware check will e failed.
The Device will find the OTA server in the network. The OTA server will
provide the necessary information to device. The device will decide if
the OTA is necessary.
Operation Mode
There are two operation modes of the device. The user can choosing
the suita le mode for application.
There are two modes “Test” and “Normal”.
“Test Mode” is for the user test the sensor function when installation.
“Normal Mode” is for the user normal use.
When the event triggered, In “Normal Mode” the LED won't indicated,
unless the attery is in the low level, the LED will flash once. And in the
“Test Mode” the LED also will light ON one second.
The PIR motion re-detected interval, in the “Test Mode” fixed to 8
seconds. In the “Normal Mode”, the PIR motion will start re-detected
interval around 30 seconds.
Notice When the tamper key of the ack side is in the released state,
the device always in the “Test Mode”.
Choosing a Suitable Location
1. The recommended mounting height is 160cm
2. Don't let the device facing the window or the sunlight.
3. Don't let the device facing the source of heat. For instance the
heater or the air-condition.
5