Philio PSK01 User manual

PSK01 Smart Keypad
The PSK01 support Z-WaveTM Multi-Functions Smart Switch to
report key status and setup rm/ Disarm.
This product can be included and operated in any Z-WaveTM
network with other Z-WaveTM certified devices from other
manufacturers and/or other applications.
The devices Built-in rechargeable Lithium-ion battery and using
DC 5V(Micro USB) charge.
Keypad function list
Multi-Functions Smart Switch to control door lock or other Z-
Wave device
Wireless 500 series Z-Wave module inside
Leading Code Function
Invisible ntenna design with good RF range
Support Security 2 Function
Beautiful touch panel, changeable white/black color panel
Built-in rechargeable Lithium-ion battery
Low battery LED indicator and report to Controller
Enable and Disable button (programmed with sensors)
Support 30 sets of user code to unlock door
Green and Red LED Indicator on the periphery
Blue and Green LED Indicator on the buttons
Long Battery life up to six months
Starting up the device for the first time
The device can not work normally at the first time.Please provide
a 5 DVC voltage through Micro USB Port to wake the device up
before the first using. fter the device is activated by connecting
to micro USB, the device will start charging and LED will light on
with red color. If the battery is full charged, LED will light on with
orange color.
1

Battery Power Check
When any keys around the central key is pressed, the device will
check the battery power. If the power level is too low, the Buzzer
can beep 3 times. Please charge the device through micro USB
immediately.
PSK01 have two KEYP D mode
1. Entry Control mode : you need to enter Usercode in order to
enter setting mode
2. Central Scene mode: you don’t need to enter Usercode in
order to enter setting mode
Entry Control mode :button LED is Green color
Central Scene mode : button LED is Blue color
*if you want to use Central Scene with zwave, have to in Central
Scene mode
PC (Programing code):defalt is (0000)
UC (Usercode):default is (1234)
ENTER PC : type 0000(default) then type ENTER
Manual control (Entry Control mode)
Manual control (Entry Control mode)
function description
dd
Programing
code
default
(0000)
1.ENTER PC
2. Enter
3.type new PC then type
*code length is 4~10 digit
(default programing code is 0000)
ex:type 0000 then enter then type 4 then type new
programing code
dd
Usercode
default
(1234)
1.ENTER PC
2. Enter
3.type newUsercode then Enter
*code length is 4~10 digit
(default programing code is 0000)
ex:type 0000 then enter then type 1 then type new
user code
2

remove
Usercode 1.ENTER PC
2. Enter
3.type Usercode then Enter
*code length is 4~10 digit
(default programing code is 0000)
ex:type 0000 then enter then type 2 then type user
code
reset 1.ENTER PC
2. Enter
(default programing code is 0000)
ex:type 0000 then enter then type 9
Z-Wave Function
ENTER PC : type 0000(default) then type ENTER
function description
dd 1. Have Z-WaveTM Controller entered
inclusion mode.
2. .ENTER PC then
3. fter add successful, the device buzzer will
beep twice
(default programing code is 0000)
ex:type 0000 then enter then type 1 & 0
Remove 1. Have Z-WaveTM Controller entered
exclusion mode.
2. ENTER PC then
3. fter remove successful, the device buzzer
will beep twice
(default programing code is 0000)
ex:type 0000 then enter then type 1 & 0
Reset 1.Press the Restore function in page 2
(reset)
2.Device can send resetlocally notification
dd
usercode
1. Z-WaveTM Controller use Command Class
User Code
2. Use Command User Code Set
3. Set User code ID,User code Status,Usercode
note : User code ID range is 1~30,
User code Status 0x01,Usercode length is 4~10,
Remove
usercode
1. Z-WaveTM Controller use Command Class
User Code
2. Use Command User Code Set
3. Set User code ID,User code Status,Usercode
note : User code ID range is 1~30,
User code Status 0x00,Usercode length is 4~10
3

Notification 1.type usercode then can send larm report
2.Behind the panel it have a tamper key
if Disassembly the pad , and release tamper key
it can send tamper report
association The device support one group,group one is for
receiving the report messange, like
1.Reset
2.Scene report
3.alarm report
4.lowbattery.
One group support 5 nodes maximun.
Smart start 1.Product has a DSK string , you can key in first
five digit to increment smart start process,or you
can scan QR code.
Ex:mydsk
10209-46687-52248-13629-04783-07465-15776-
56519
2.SmartStart enabled products can be added into
a Z-Wave network by scanning the Z-Wave QR
Code present on the product providing
SmartStart inclusion. No further action is required
and the SmartStart product will be added
automatically within 10 minutes of minutes On in
the network vicinity
Entry Control Function
Dis rm
mode set
1. Make sure pad mode is safe mode
2. enter usercode then ENTER
3. it can send disarm report
rm mode
set
1. Make sure pad mode is safe mode
2. enter
3. it can send disarm report
Central Scene Function
Central
Scene report
1.Make sure pad mode is non safe mode or
already type usercode.
2.Press 1 or 2 times in 2 sec. or hold on for 2
sec.or release any one of key.
Z-Wave configuration
NO Name Def Valid description
1 Set
KEYP D
mode
0x01 1~2 1: Entry Control mode
2: Central Scene mode
4

Notice 1: lways remove a Z-Wave device before trying to add it
to a Z-Wave network .
Notice 2: This product can be operated in any Z-Wave network
with other Z-Wave certified devices from other manufacturers. ll
non-battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the
network..
Over The ir Firmware Update
The device support the Z-Wave firmware update via OT .
Let the Z-WaveTM Controller into the firmware update mode,
chose the hex file to update. Wait for 10~15 minutes.
t that time, please don't remove the battery, otherwise it will
cause the firmware broken, and the device will no function.
Result will show in Z-WaveTM Controller log.
Z-Wave Supported Command Class
COMM ND_CL SS_ZW VEPLUS_INFO
COMM ND_CL SS_SUPERVISION,
COMM ND_CL SS_TR NSPORT_SERVICE_V2
COMM ND_CL SS_SECURITY
COMM ND_CL SS_SECURITY_2
COMM ND_CL SS_VERSION*
COMM ND_CL SS_M NUF CTURER_SPECIFIC*
COMM ND_CL SS_DEVICE_RESET_LOC LLY*
COMM ND_CL SS_POWERLEVEL*
COMM ND_CL SS_ENTRYCONTROL*
COMM ND_CL SS_CENTR L_SCENE*
COMM ND_CL SS_B TTERY*
COMM ND_CL SS_USER_CODE*
COMM ND_CL SS_ SSOCI TION_V2*
COMM ND_CL SS_MULTI_CH NNEL_ SSOCI TION_V2*
COMM ND_CL SS_ SSOCI TION_GRP_INFO*
COMM ND_CL SS_FIRMW RE_UPD TE_MD_V2*
* Command Class Requires Security
Installation steps
. Mount the bracket to the rear of the body first.
B. Remove the double-sided adhesive release paper on the
bracket and stick it on the wall surface.
C. Push up the PSK01 and remove it. If necessary, lock it.
Screw up, you can take the opposite way of PSK01
How to use the table
Insert the back frame into the screw hole at the rear of the
PSK01 to stand at the table.
5

Install the PSK01 body to the W LL BOX
. Remove the screws on the left and right sides of the panel
B. Use two removal holes to remove the panel
C. Remove the screw cover
D. Install the PSK01 body to the W LL BOX and lock the screws.
E. Install the screw cover back
F. Install the outer frame. When installing, pay attention to the
parallel connection between the panel and the body to prevent
the O-ring from coming out.
G. Lock back panel screws
Tamper Switch
If the tamper switch be released, the device will send the alarm
report .
Troubleshooting
Symptom Cause of Failure Recommendation
The device can not
work
Battery is
running out of
power
Charging the
battery by Micro
USB.
The device can not
join to Z-Wave
The device may
in a Z-Wave
Exclude the
device then
6

network network. include again.
Button no response The button will
no response
when LED is
flashing.
Wait for the LED go
out and try again.
Specification
Rated Voltage (rechargeable
Lithium-ion battery)
DC3.5V~4.2V
Rated Voltage (Micro USB) DC5V
Operating Temperature 0°C - 40°C
Location IP44 (indoor and outdoor)
Frequency Range 868.40MHz & 869.85MHz / EU
(PSK01-EU);
908.4MHz & 916.0MHz / US
(PSK01-US);
922-927MHz / J P N
(PSK01-JP);
RF Maximum Power (Peak) +5dBm (Peak)
RF Maximum Power ( verage) -10dBm ( verage)
Transmission Range Minimum 40 m in door 100m
outdoor line of sight
Modulation Type FSK (Frequency-Shift Keying)
** Specifications are subject to change and improvement without
notice.
FCC ID: RHHPSK01
C UTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
Choosing a Suitable Location
1. Do not locate the Module facing direct sunlight, humid or dusty
place.
2. The suitable ambient temperature for the Module is 0°C~40°C.
3. Do not locate the Module where exists combustible
substances or any source of heat, e.g. fires, radiators, boiler etc.
Disposal
This marking indicates that this product should not
be disposed with other household wastes
throughout the EU. To prevent possible harm to the
7

environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To
return your used device, please use the return and
collection systems or contact the retailer where the
product was purchased. They can take this product
for environmental safe recycling.
Philio Technology Corporation
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City
24257, Taiwan(R.O.C)
w ww.philio-tech.com
FCC Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in
a particular installation.
If this equipment does cause harmful interference to radio or tele-
vision reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the fol-
lowing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation is
subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: ny changes or modifications not expressly ap-
proved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
8