Philips OccuSwitch DALI User manual

OccuSwitch DALI Commissioning Guide
with the IRT8097

Philips OccuSwitch DALI Commissioning Guide - IRT8097
Content Calibrate the light level
DALI function assignment
Movement test
Switch lights on or off
Enable 100h. no dimming
Commissioning of switches with
Enocean®RF technology
Contact
1
1
2
2
3
4
5
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
Attention
Always keep pointed to OccuSwitch DALI sensor

Philips OccuSwitch DALI Commissioning Guide - IRT8097 1
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
Calibrate the light level
Press “5” “6” to set
the required light level
Press “save”
Attention
Always calibrate the installation
Attention
Calibration must be done at night and
ofce must be furnished
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
1
2
DALI function assignment
Press “DALI”
Wait for a luminaire
to ash
Select function for this luminaire
c = corridor
w = window
Repeat for next
ashing luminaire
Press “DALI” to abort)
When nished all
luminaires ash once
1
2
3
4
(5
6

Philips OccuSwitch DALI Commissioning Guide - IRT80972
Switch lights on or off
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
Movement test
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
1
2
Press “test”
OccuSwitch DALI will now
operate 10x faster than normal.
MD timer = 30sec xed
Press “test” to stop
(automatic stop after 60s
no movement)
Press “on”
Press “off ”
1
2

Philips OccuSwitch DALI Commissioning Guide - IRT8097 3
DALI
address
mode
mode ? test
background
basics
10%
40%
30%
min.
20%
50%
power up
IR group
power uppower up
A
D
G
C
F
B
E
C
a
l
i
b
r
a
t
i
o
n
60% 70%
%
1
4
7
3
6
9
on off
2
5
10
8
1-10
A-G
on/off
save
w
w
w
.
p
h
i
l
i
p
s
.
c
o
m
/
o
m
n
i
p
r
o
g
Enable 100h. no dimming
test
off
on
100 h
DALI
address
www.philips.com/omniprog
save
c
w
1
2
Press “100h”
OccuSwitch DALI will not dim
anymore for 100 hours burning
time. (calibration is still possible!)
LED is constant green
Press “100h”
OccuSwitch DALI will function
normally and 100h counter will
be reset.

Philips OccuSwitch DALI Commissioning Guide - IRT80974
Commissioning of switches with Enocean®RF technology
Procedure
Shortly press the front button of the OccuSwitch DALI,
The LEDs will ash shortly.
Press again but now hold the button down until
the green and red LEDs start to ash rapidly.
Wait till the ashing slows down.
Press one of the keys of the switch you want to bind to the OccuSwitch DALI.
Press 0 or 1
Function = window + corridor control
Press B 0
Function: B = window+corridor control
A = additional channel (= 4) control
Press B 1
Function: B = window control
A = corridor control
The system will not recognise the dual rocker if you use the buttons A0 or A1,
but commission only the A switch as single rocker.
The LEDs will ash rapidly again.Wait till the ashing slows down.
You can now bind another switch.
Press the front button (shortly), or wait for 30 seconds, to stop the commissioning.
The green/red ashing will now stop and normal operation is resumed.
If you make a mistake or want to make alterations, stop the commissioning process, and restart again.
Start of commissioning will always remove existing bindings.
0
1
0 0
1 1
B A

Philips OccuSwitch DALI Commissioning Guide - IRT8097 5

Philips Lighting B.V.
www.philips.com/omniprog
www.philips.com/occuswitchdali
Although this information has been prepared with extreme care, no rights
can be derived from any information and illustration in this manual.
3222 636 49141
December 2010
Contact