Philips P-5561-D User manual

etal Halide Econ-o-watt lamps
Philips Metal Halide Econ-o-watt lamps offer a range
of switch start quartz metal halide lamps for long life and
high efficiency.
Replaces 400W Standard Metal Halide Lamps
• Reduces energy usage by 40W compared to a 400W Metal Halide Lamp
• ame 36,000 initial lumens as a 400W Metal Halide Lamp
• ame 20,000 hours rated average life as a 400W Metal Halide Lamp
• Operates on tandard Metal Halide Ballasts
Philips Metal Halide
360 Watt Econ-o-watt®
Ideal for industrial
applications, warehouses
and parking lots
METAL HALIDE LAMP
P-5661-D Metal halide 360 Econ_P od_Bulletin:Layout 1 4/2/08 5:35 PM Page 1

Philips Metal Halide 360 Watt Econ-o-watt®
Ordering, Electrical and echnical Data
Rated Approx. Approx.
Product Ordering ANSI Pkg. LCL MOL Avg.Life Initial Mean CC
Number Code Code Watts Bulb Base Qty. (In.) (In.) (Hrs.)1Lumens2Lumens3CRI (Kelvin)4
39065-8 M 360/BU/EW M165/M59/ 360 ED-37 Mog. 6 7.0 11.5 20,000 36,000 24,500 60 4300
39066-6 M 360/C/BU/EW M165/M59/ 360 ED-37 Mog. 6—11.5 20,000 34,200 22,600 65 4000
1) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per start.
It is based on survival of at least 50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.
2) Approximate lumen values listed are for vertical operation of the lamp.
3) Approximate lumen output at 40% of lamp rated average life.
4) Approximate color temperature in Kelvin degrees.
Above specifications are subject to change without notice.
© 2008 Philips Lighting Company.All rights reserved.
Printed in U A 4/08
P-5561-D
www. philips.com
Philips Lighting Company
200 Franklin quare Drive
P.O. Box 6800
omerset, NJ 08875-6800
1-800-555-0050
A Division of Philips Electronics North America Corporation
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2 3
1-800-555-0050
A Division of Philips Electronics Ltd.
WARNINGS,CAU IONS AND OPERA ING INS RUC IONS FOR
S ANDARD ME AL HALIDE LAMPS (ENCLOSED FIX URES ONLY
UNLESS O HERWISE NO ED)
R
WARNING: These lamps can cause serious skin burn and eye inflammation from short wave
ultraviolet radiation if outer envelope of the lamp is broken or punctured. Do not use where people
will remain for more than a few minutes unless adequate shielding or other safety precautions are used.
Certain lamps that will automatically extinguish when the outer envelope is broken or punctured are
commercially available.”This lamp complies with FDA radiation performance standard 21 CFR subchapter
J. (USA: 21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off at once and replace the lamp to avoid
possible injury from hazardous short wave ultraviolet radiation. Do not scratch the outer
bulb or subject it to pressure as this could cause the outer bulb to crack or shatter.A
partial vacuum in the outer bulb may cause glass to fly if the envelope is struck.
WARNING:The arc-tube of metal halide lamps are designed to operate under high pressure and at
temperatures up to 1000º C and can unexpectedly rupture due to internal or external factors such as a
ballast failure or misapplication. If the arc-tube ruptures for any reason, the outer bulb may break and
pieces of extremely hot glass might be discharged into the surrounding environment. If such a rupture
were to happen, HERE IS A RISK OF PERSONAL INJURY, PROPER Y DAMAGE, BURNS
AND FIRE.
Certain lamps that will retain all the glass particles should inner arc-tube rupture occur
are commercially available from Philips Lighting Company.
RELAMP FIX URES A OR BEFORE HE END OF RA ED LIFE.Allowing lamps to
operate until they fail is not advised and may increase the possibility of inner arc
tube rupture.
CAU ION:TO REDUCETHE RISK OF PERSONAL INJURY, PROPERTY DA AGE, BURNS AND
FIRE RESULTING FRO AN ARC-TUBE RUPTURETHE FOLLOWING LAMP OPERA ING
INS RUC IONS UST BE FOLLOWED:
LAMP OPERA ING INS RUC IONS:
1.Turn off lamps at least once a week for at least 15 minutes in systems which are operating on a continuous
basis (24 hours/day-7days/week). FAILURE TO TURN OFF LA PS FORTHE INI U
RECO ENDED TI E AY INCREASETHE POSSIBILITY OF AN INNER ARC-TUBE RUPTURE.
2. RELA P FIXTURES AT OR BEFORETHE END OF RATED LIFE.Allowing lamps to operate until they
fail is not advised and may increase the possibility of inner arc tube rupture.
3.Use only in an enclosed fixture capable of withstanding particles of glass having temperatures up to 1000º C.
4. Before lamp installation/replacement, shut power off and allow lamp and fixture to cool to avoid
electrical shock and potential burn hazards.
5. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage limits
recommended by ballast manufacturer.
A. Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
6. Periodically inspect the outer envelope. Replace any lamps that show scratches, cracks or damage.
7. If a lamp bulb support is used, be sure to insulate the support electrically to avoid possible
decomposition of the bulb glass.
8. Protect lamp base, socket and wiring against moisture,corrosive atmospheres and excessive heat.
9. Time should be allowed for lamps to stabilize in color when turned on for the first time.This may
require several hours of operation, with more than one start. Lamp color is also subject to change
under conditions of excess vibration or shock and color appearance may vary between individual lamps.
10. Lamps may require 10 to 20 minutes to re-light if there is a power interruption.
11. Take care in handling and disposing of lamps. If an arc tube is broken, avoid skin contact with any of
the contents or fragments.
12. Do not use this lamp:
A. In a fixture that contains a Pulse Start metal halide ballast.
B. In a fixture that is specifically designed for use with Pulse Start metal halide lamps. Operation
of these lamps on Pulse Start Metal Halide systems may increase the chance of
an outer bulb rupture and pieces of extremely hot glass might be discharged
into the surrounding environment. If such a rupture were to happen, HERE IS A
RISK OF PERSONAL INJURY, PROPER Y DAMAGE, BURNS AND FIRE.
B
A
Lamp Dimensions
Metal Halide 360W ED-37
A — 4.625"
B — 11.5"
P-5661-D Metal halide 360 Econ_P od_Bulletin:Layout 1 4/2/08 5:35 PM Page 2