Philips CED1900BT User manual

Register your product and get support at
www.philips.com/welcome
Always there to help you
Manuale utente 77
Gebruiksaanwijzing 103
Instrukcjaobsługi 129
User manual 3
Gebruiksaanwijzing 25
Moded’emploi 51
CED1900BT
Question?
Contact
Philips

1
English
EN
Contents
1 Safety 2
2 Yourcarentertainmentsystem 2
Introduction 2
What's in the box 3
3 Install the car entertainment system 3
Connect wires 3
Mount into the dashboard 7
4 Get started 8
Prepare the remote control 8
Turn on 8
Use the home menu 9
Set the date and time 9
5 Playfromhardmedia 10
Load a disc 10
Connect a USB storage device 10
Insert an SD/SDHC card 10
Control play 11
Browse recorded les 12
6 Listen to radio 12
Switch to radio mode 12
Set up 12
Tune to a radio station 13
Store radio stations in memory 13
Tune to a preset radio station 13
7 Use the navigation system 14
Insert the map data card 14
Navigate your road trip 14
8 Use Bluetooth devices 14
Activate the Bluetooth function 14
Pair a device 14
Play audio from a connected device 16
Make a call 16
9 PlayfromaniPod/iPhone 17
Compatible iPod/iPhone models 17
Connect your iPod/iPhone 17
Control play 18
Charge your iPod/iPhone 18
10 Adjust sound 18
Adjust the volume level 18
Mute sound 18
11 Others 18
Play external audio/video input 18
Use rear monitors 19
Use buttons on the steering wheel 19
Set the rear view camera 20
Reset the system 20
12 Productinformation 20
13 Troubleshooting 22
General 22
About the Bluetooth device 22
14 Notice 23
Compliance 23
Care of the environment 23
Trademark notice 23
Copyright 24
Contents

2EN
1 Safety
Read and understand all instructions before you use the
device. If damage is caused by failure to follow instructions,
the warranty does not apply.
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
• The device is designed for negative ground (earth) 12 V
DC operation only.
• To reduce the risk of trafc accidents, do not watch
video when driving.
• To ensure safe driving, adjust the volume to a safe and
comfortable level.
• Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
• Use only the supplied mounting hardware for a safe
and secure installation.
• To avoid short circuits, do not expose the device,
remote control or remote control batteries to rain or
water.
• The device shall not be exposed to dripping or
splashing.
• Do not place any sources of danger on the device (e.g.
liquid lled objects, lighted candles).
• Never insert objects into the ventilation slots or other
openings on the device.
• Never place any objects other than discs into the disc
tray/slot.
• To avoid exposure to laser radiation, do not
disassemble the device.
• Risk of damage to the screen! Never push, rub, or strike
the screen with any object.
• Never use solvents such as benzene, thinner, cleaners
available commercially, or anti-static sprays intended
for discs.
• Clean the device with soft, damp cloth. Never use
substances such as alcohol, chemicals or household
cleaners on the device.
• Risk of swallowing coin battery!
• The device may contain a coin/button type
battery, which can potentially be swallowed. Keep
the battery out of reach of children at all times! If
swallowed, the battery can cause serious injury or
death. Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been swallowed
or placed inside any part of the body, seek
immediate medical attention.
• When you change the batteries, always keep all
new and used batteries out of reach of children.
Make sure that the battery compartment is
completely secure after you replace the battery.
• If the battery compartment cannot be completely
secured, discontinue use of the product. Keep out
of reach of children and contact the manufacturer.
2 Yourcarentertainment
system
Congratulations on your purchase, and welcome to Philips!To
fully benet from the support that Philips offers, register your
product at www.philips.com/welcome.
Introduction
With the car entertainment system, you can
• listen to music,
• watch videos,
• view pictures,
• listen to FM (RDS included) and AM/MW radio,
• make phone calls via Bluetooth, and
• navigate your road trip.

3
English
EN
What's in the box
Check and identify the contents of the package:
1Main unit (with a sleeve) 2Remote
control
3Trim plate 4Rubber
cushion
5Screw X 4 (M5x8mm) 6Hexagon
head screw
7Remote control battery 8User manual
3 Install the car
entertainment system
Always follow the instructions in this chapter in sequence.
These instructions are for a typical installation. However, if
your car has different requirements, make the adjustment
accordingly. If you have any question regarding installation kits,
consult your local retailer.
abc
def
g h
Note
•This system is designed for negative ground (earth) 12V
DC operation only.
•Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
•To avoid short-circuit: before you connect, make sure
that the ignition is off.
•Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
•Make sure that all loose leads are insulated with
electrical tape.
•Make sure that the leads do not get caught under
screws iron parts that will move (e.g. seat rail).
•Make sure that all ground (earth) leads are run to a
common ground (earth) point.
•Use only the supplied mounting hardware for a safe
and secure installation.
•Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
•When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
•Never connect speaker wires to the metal body or
chassis of the car.
•Never connect speaker wires with stripes to one
another.
Connect wires
Note
•The ISO male connectors are not supplied.
•Make sure that all loose leads are insulated with
electrical tape.
•Consult a professional to connect wires as instructed
below.
•Before connection, check the car's wiring carefully.
1 Connect the ISO male connectors.

4EN
ISO male
connectors Connect to
a Green strip, black-edged
green strip
Rear left speaker
b White strip, black-edged
white strip
Front left speaker
c Gray strip, black-edged
gray strip
Front right speaker
d Purple strip, black-edged
purple strip
Rear right speaker
e Red strip Ignition key +12V DC
when ON/ACC
f Blue strip Motor/electric antenna
relay control lead
g White-edged blue strip Amplier relay control
lead
h Black strip Ground
i Yellow strip The +12V car battery
which is energized at
all times
2 Connect other wires if necessary.
Caution
•To avoid an accident, the driver must not watch video
while driving. By design, this system disallows watching
video during drive. Park your car in a safe place and
engage the parking brake before watching video.
Note
•When the parking brake of your vehicle is not engaged,
the video blocking system is activated. It blocks the
display of front video source only.
•If the system is not properly connected with the
parking brake control module of your vehicle, video
signals will be blocked by the system, with the below
message displayed on the TFT.
Connectors and
sockets on rear panel External sockets or connectors
1 For ISO male connectors As indicated above
2REAR OUT L (White
socket)
Rear left speaker
3REAR OUT R (Red socket) Rear right speaker
4FRONT OUT R
(Red socket)
Front right speaker
5FRONT OUT L
(White socket)
Front left speaker
6VIDEO OUT 1
(Yellow socket)
Video input socket
of an external display
device
7VIDEOOUT2
(Yellow socket)
Video input socket
of an external display
device
8VIDEO IN (Yellow socket) Video output socket of
an external player
9CAMERA IN (Purple socket) Video output socket of
an external camera
10 SUB-W OUT (Blue socket) Sub-woofer
11 AV-IN L (White socket) Left audio channel
output socket of an
external player
12 AV-IN R (Red socket) Right audio channel
output socket of an
external player
13 REVERSE CAMERA
(Purple wire)
Reverse camera (B+)
14 PARKINGBRAKE
(Pink wire)
Parking brake (-)
15 OE SWC IR REMOTE IN
(Brown wire)
OE SWC remote in
16 OE SWC IR REMOTE IN
(Black wire)
Ground
17 OE SWC AD LEARN
(White wire)
OE SWC AD Learn
line 1
18 OE SWC AD LEARN
(White wire)
OE SWC AD Learn
line 2
19 OE SWC AD LEARN
(Black wire)
Ground
20 External Mic
(Black connector)
External microphone
21 EXTERNAL BOX
CONNECTOR
(Black connector)
External navigation box
22 GPSAERIAL
(Black connector)
GPS smart antenna
23 RADIO ANTENNA
(Black connector)
Radio antenna

5
English
EN
Connectors and
sockets on rear panel External sockets or connectors
24 Rear Monitor Audio Out 1
(White connector)
Left audio channel
input socket of one
rear monitor
25 Rear Monitor Audio Out 1
(Red connector)
Right audio channel
input socket of one
rear monitor
26 RearMonitorAudioOut2
(White connector)
Left audio channel
input socket of another
rear monitor
27 Rear Monitor Audio Out
2(Red connector)
Right audio channel
input socket of another
rear monitor
Tip
•The pin arrangement for the ISO connectors depends
on the type of your vehicle.To avoid damage to the
system, connect properly.

6EN
a
bcde fghij
kl
m
n
o
p
q
r
s
t
u
v
w
x
y
z

7
English
EN
Mount into the dashboard
Note
•Make sure that wires are correctly connected before
you mount the main unit into a car.
•If preset radio stations are lost when the ignition key
is turned OFF and then back ON, reconnect the red
leads crosswise to the yellow ones.
1 If the car does not have an on-board drive or
navigation computer, disconnect the negative terminal
of the car battery.
• If you disconnect the car battery in a car that has
an on-board drive or navigation computer, the
computer may lose its memory.
• If the car battery is not disconnected, to avoid
short-circuit, make sure that bare wires do not
touch each other.
2 Make sure that the car dashboard opening is within
these measurements:
• Since the unit cannot be used if the dashboard
opening's slant angle is above 20 degrees, make
sure that the horizontal slant of the car dashboard
opening is between 0 and 20 degrees.
182 mm
112 mm
5 mm
3 Remove the mounting sleeve with the supplied
disassembly tools.
4 Install the sleeve into the dashboard and bend the tabs
outward to x the sleeve.
• If the system is not xed by sleeve but by the
supplied screws, skip this step.
5 Slide the unit into the dashboard until a click sound is
heard.
6 Attach the trim plate.
7 Reconnect the negative terminal of the car battery.

8EN
4 Get started
Caution
•Risk of car accidents! Never watch video or operate
this system while driving.
Preparetheremotecontrol
Forthersttimeuse
Pull the protective sheet out.
» The remote control is ready for use.
Replace the battery
Caution
•Risk of explosion! Keep batteries away from heat,
sunshine or re. Never discard batteries in re.
Note
•Remove the battery if it is exhausted or if the remote
control is not to be used for a long time.
•Batteries contain chemical substances, they should be
disposed of properly.
•Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
1 Pull out the battery tray.
2 Insert one CR2025 battery with correct polarity (+/-)
as indicated.
3 Insert the battery tray.
Turn on
Press .
» PHILIPS logo and a progress bar are displayed
while boot-up.
• To turn off the system, press and hold for
3 seconds.
Forthesttimeuse
After successful boot-up, the following interface is displayed.
1 Tap to select a language for on-screen display.
» The following interface is displayed.
2 Tap to select a radio region that matches your location.
» The following interface is displayed.
3 Tap [Finish] to complete the initial setup.
» The device switches to radio mode automatically.

9
English
EN
Use the home menu
Note
•If is displayed when you touch an icon, it indicates
that the selected media or feature is unavailable at the
current time.
Access the home menu
Tap to access the home menu.
» The clock, date, and the bar for popular icons are
displayed.
• To access the full menu with all feature icons displayed,
tap .
• To return to the home menu, tap .
• [Radio]: Switch the source to FM/AM radio.
• [Disc]: Switch the source to disc.
• [USB]: Switch the source to USB storage
device.
• [SDHC]: Switch the source to SD/SDHC
card.
• : Once your iPod/iPhone is connected and
recognized, this icon is displayed in the bar of
favorite icons.Tap it to switch the source back to
iPod/iPhone.
• [Navigation]: Access the navigation system.
• [Bluetooth]: Use the Bluetooth feature.
• [AV-IN 1]/[AV-IN2]: Switch the source to the
audio and video input that is transferred from an
external video player.
•
R
[Rear zone]:Access the settings for rear
monitors.
• [SWC]:Access the interface to assign
functions to buttons on the steering wheel.
• [Settings]:Access the system menu.
Set the date and time
1 Tap > to access the full menu with all feature
icons displayed.
2 Tap [Settings].
» The [General]menu is displayed.
3 Tap [Clock Mode] to select a time format.
• [24Hr]: 24-hour time format
• [12Hr]: 12-hour time format
4 Tap [Date] to display the interface for setting the date.
5 Tap to set the year, month, and date.
6 Tap [Time] to display the interface for setting the time.
7 Tap to set the hour and minute.
8 Tap to return to the home menu.

10 EN
5 Playfromhardmedia
You can use this system to listen to audio, watch videos, and
view photos that are stored on a disc, USB storage device, or
SD/SDHC card.
Note
•Before use, check for compatible media.
Load a disc
Caution
•Never insert any object other than a disc of 12-cm
diameter into the disc slot.
1 Insert the disc into the disc slot with the label side
facing up.
» Play starts automatically.
• If play does not start automatically, tap the screen
to display the icon, and then tap to start
play.
2 To eject the disc, press .
» When the disc is ejected, the system switches to
the previous source or radio mode.
Region Code
You can play DVD discs marked with the following region code.
DVD region code Countries
Europe
Connect a USB storage device
Note
•Make sure that the USB storage device contains
compatible les.
•NTFS (New Technology File System) le system is not
supported.
1 Push the USB socket cover upwards to open it.
2 Connect the USB storage device to the USB socket.
» Play starts automatically.
• To remove the USB storage device, switch the
system to another source rst.
Insert an SD/SDHC card
Note
•Make sure that the SD/SDHC card contains compatible
les.
•NTFS (New Technology File System) le system is not
supported.
1 Flip up the protective cover.
2 Insert the SD/SDHC card into the slot until you
hear a "click".
» Play starts automatically.
Remove the SD/SDHC card
1 Switch system to another source.
2 Press the card inwards until you hear a "click".
» The card is disengaged.
3 Pull out the SD/SDHC card.

11
English
EN
Control play
Videos
• : Return to the home menu.
• : Zoom in or out of the image.
• : Select an available audio channel or audio language.
• : Select an available subtitle.
•
• For DVD, return to the disc menu or root menu.
• For recorded les, return to the list of les or
folders.
• PBC: ForVCD/SVCD only, enable or disable the PBC
(Playback Control) feature.
• / : Skip to the previous or next title,
chapter, track, or le.
• To search forward fast or rewind the track, tap on
the progress bar.
• / : Start, pause, or resume play.
• : Display control icons on the second page.
• : Select a repeat mode.
• DVD: [Repeat chapter] (repeat the current
chapter), [Repeat title] (repeat the current title),
[Repeat all] (repeat all chapters and titles), or
[Repeat off] (cancel repeat play).
• VCD/SVCD: [Repeat one] (repeat the current
track) or [Repeat all] (repeat all tracks).
• Recorded les: [Repeat one] (repeat the current
video le), [Repeat folder] (repeat all video les in
the current folder), or [Repeat all] (repeat all video
les).
• [16:9]/[4:3]: Select an aspect ratio.
• :Tap to display the brightness bar, and then tap on
the bar to adjust the screen brightness.
• :Tap to display the contrast bar, and then tap on
the bar to adjust the image contrast.
• :Tap to display the saturation bar, and then tap on
the bar to adjust the image saturation.
• : Display control icons on the rst page.
Audios
• : Return to the home menu.
•
• Press once to access the track list.
• Press twice to access the folder list.
• Press repeatedly to return to the playback
interface.
• : For recorded les only, skip to the next audio
folder.
• : Return to the list of tracks or folders.
• / : Skip to the previous or next track.
• To search forward fast or rewind the track, tap on
the progress bar.
• / : Start, pause, or resume play.
• / / : Select a repeat mode.
• : Repeat the current track.
• : For recorded les, repeat all tracks in the
current folder.
• (highlighted): Repeat all tracks.
• : Select random play ( highlighted) or
sequential play ( in gray).

12 EN
Pictures
• : Return to the home menu.
• : Zoom in or out of the picture.
• / : Rotate the picture clockwise or anti-clockwise
by 90 degrees.
• / : Return to the list of les or folders.
• / : Select the previous or next picture.
• / : Pause or resume the slideshow.
• : Display control icons on the second page.
• [16:9]/[4:3]: Select an aspect ratio.
• :Tap to display the brightness bar, and then tap on
the bar to adjust the screen brightness.
• :Tap to display the contrast bar, and then tap on
the bar to adjust the image contrast.
• :Tap to display the saturation bar, and tap on the
bar to adjust the image saturation.
• : Display control icons on the rst page.
Browserecordedles
During playing recorded les, you can access the le list and
select les from the list.
1 Tap to access the list of les or folders.
2 Tap an icon to select a le category.
• : Display the list of audio tracks or folders.
• : Display the list of picture les or folders.
• : Display the list of video les or folders.
3 Tap the name of a le to start play.
6 Listen to radio
Switch to radio mode
After the boot-up at the rst time, the system switches to
radio mode automatically.
To switch the source back to radio afterwards, tap
[Radio] on the home menu.
» The interface for radio is displayed.
Set up
Before you search for radio stations, make prior setup.
Tap to display the setup menus.
Select a radio range
1 Tap [Radio Range].

13
English
EN
2 Tap [Distance] or [Local] to select a tuner sensitivity.
• [Distance]: Stations with strong and weak signals
can be tuned to.
• [Local]: Only stations with strong signals can be
tuned to.
Enable the RDS feature
Note
•RDS feature is enabled by default.
•Only after the RDS feature is enabled, the option of
[PTYlist] is displayed.
Tap [RDS Off] (RDS disabled) to enable the RDS feature.
» The option of [PTYlist]is displayed.
• To disable the RDS feature, tap [RDS On] (RDS
enabled).
Tune to a radio station
1 Tap FM or AM to select a band.
• FM bands: FM1,FM2,FM3
• AM bands: AM1,AM2
2 Tap or repeatedly until the frequency of target
radio station is displayed.
• To tune to a radio station automatically, tap and
hold or until the frequency digits start
change.
Tip
•You can also press BAND on the remote control
repeatedly to select a band.
Store radio stations in memory
You can store up to 6 stations in each band.
Store radio stations manually
1 Select a band.
2 Tune to the target radio station.
3 Tap and hold one of the channels (1to 6) over two
seconds.
» The radio station is saved under the selected
channel.
Store radio stations automatically
You can search for a radio station with intro search, which
broadcasts a 10-second preview of each detected radio
station.
1 Select a band.
2 Tap .
3 Tap [Auto Store].
» Auto search starts.The six strongest stations of
the selected band are saved in preset channels
automatically.
Tune to a preset radio station
1 Select a band.
2 Tap one of the preset channels (1to 6) to select a
preset radio station.

14 EN
7 Use the navigation
system
Insert the map data card
Note
•The map data card is not included in the packaging.
•Before using the map data card, update the map data
if necessary.
1 Flip up the protective cover.
2 Insert the map data card into the MAP slot until you
hear a "click".
3 Close the protective cover.
Navigate your road trip
Note
•Risk of trafc accident! Never operate the navigation
system during drive. Complete the setting of your
destination and other navigation specications before
you drive.
1 Press NAVI.
• You can also tap on the home menu to access
the navigation system.
» The navigation interface is displayed in a few
seconds.
2 Follow the user manual of the navigation map to set
navigation specications.
8 Use Bluetooth devices
With this system, you can listen to audio from a player and
make a call through Bluetooth.
Activate the Bluetooth function
• On the home menu, tap .
• In any other mode, tap on top of the screen.
Pairadevice
Note
•Philips does not guarantee the compatibility with all
Bluetooth devices.
•Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
•Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
•The operational range between this system and a
Bluetooth device is approximately 8 meters (24 feet).
•Any obstacle between this system and a Bluetooth
device can reduce the operational range.
•Keep away from any other electronic device that may
cause interference.
Pairtherstdevice
1 Activate the Bluetooth function on this system.
» The following interface is displayed.
2 Tap on this system to search for other Bluetooth
devices.

15
English
EN
3 In the device list, tap the name of your Bluetooth
device, and then tap behind the name.
» The paring starts, and then a pairing request from
CED1900 is displayed on your device.
4 On your device, accept the pairing request from
CED1900, enter the default password '0000', and then
conrm the password entry.
» [PairedOK!] ashes, and then [Connecting] is
displayed on this system.
5 On your device, enable or permit the connection with
CED1900.
• If a player is connected, the music playback
interface is displayed on this system.
:Tap it to return to the music playback
interface.
:Tap it to display the list of paired mobile
phones.
:Tap it to display the list of paired mobile
phones.
:Tap it to display the list of paired mobile
phones.
• If a mobile phone is connected, the keypad is
displayed on this system.
:Tap it to display the list of paired players.
:Tap it to display the on-screen keypad for
phone calls.
:Tap it to display the phone book that is
synchronized with your mobile phone and keypad.
:Tap it to display the list of favorite contacts.
Pairmoredevices
1 Activate the Bluetooth function on this system.
» One of the following interfaces is displayed.
2 Tap on the top right corner.
3 Tap [NewPairing] to start searching for Bluetooth
devices.
4 Repeat steps 3 to 5 that are indicated in the above
section "Pair the rst device" to complete the
connection.
Note
•You can connect a music player and a mobile phone
simultaneously.

16 EN
Manage paired devices
1 Activate the Bluetooth function.
2 Tap or .
• To manage paired players, tap .
• To manage paired mobile phones, tap .
3 Tap on the top right corner.
4 Tap [PairedDevice].
» The list of paired devices is displayed.
5 Tap the name of the paired device that you want to
reconnect, disconnect, or delete.
• :Tap to reconnect the device.
• :Tap to disconnect the device.
• :Tap to delete the device from the list of
paired devices.
6 Tap , , or .
Tip
•If you want to manually reconnect a device after the
connection is interrupted, disable the function of
automatic connection.
Playaudiofromaconnecteddevice
If the connected Bluetooth device supports Advanced Audio
Distribution Prole (A2DP), you can listen to tracks that are
stored on the device through the system. If the device also
supports Audio Video Remote Control Prole (AVRCP)
prole, you can control play on the system or with its remote
control.
1 Play a track on the connected device.
2 On this system, tap to display the music playback
interface.
3 Tap icons on the interface to control play.
• : Pause or resume play.
• / : Select the previous or next
track.
Note
•If the connected device does not support the AVRCP
prole, control play on the connected device.
Make a call
Note
•Keep the Bluetooth connection active between the
system and your mobile phone.
Call a number
You can make phone calls with the system.
1 Tap on top of the screen.
» The keypad is displayed.
• If the keypad is not displayed, tap .
2 Tap number icons to enter the phone number.
• To clear the last digit, tap .
• To clear all digits, tap .
• To return to the previous screen, tap .

17
English
EN
3 Tap to send the call.
• To end the call, tap .
• To enter numbers during the call, tap to
display the keypad rst.
Redial the last called number
1 Tap .
» The last called number is displayed.
2 Tap again to send the call.
Answer a call
Note
•By default, all incoming calls are picked up automatically.
You can disable the function of automatic answer.
1 When there is an incoming call, [Incoming call…] is
displayed on the screen.
2 Tap to answer the call.
• To reject or end the call, tap .
Transfer a phone call to mobile phone
By default, the voice comes from the loudspeakers during a
call.
1 Tap to transfer the phone call to your mobile
phone.
» The loudspeakers are muted, and the voice comes
from the mobile phone only.
2 Take up your mobile phone for the conversation.
9 PlayfromaniPod/
iPhone
Note
•During play, no audio signals are transferred through
the headphone socket of your iPod/iPhone.
CompatibleiPod/iPhonemodels
This system supports the following iPod and iPhone models.
• iPhone 4, iPhone 3GS, iPhone 3G, and iPhone
• iPod touch (1st, 2nd, 3rd, and 4th generations)
• iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generations)
• iPod classic
ConnectyouriPod/iPhone
Connect an Apple 30-pin USB cable to:
• the USB socket on the front panel of this system, and
• your iPod/iPhone.
» The system starts playing tracks that are stored on
your iPod/iPhone.
• Once your iPod/iPhone is connected and recognized,
is displayed in the bar of popular icons on the
home menu.You can tap it to switch back to this
playback interface.
Note
•Before you disconnect your iPod/iPhone, switch the
system to another source.

18 EN
Control play
By default, use the on-screen playback interface of this system
to control play.
• :Tap to pause play.
• :Tap to resume play.
• / :Tap to play the previous or next
track.
• / :Tap to select a repeat mode.
• : Repeat the current track.
• (highlighted): Repeat all tracks.
• (in gray): Cancel repeat play.
• :Tap to select a play mode.
• (highlighted): Play tracks randomly.
• (in gray): Play tracks in sequence.
• :Tap to switch to the iPod control mode, and then
you can control play on your iPod/iPhone.
• :Tap to switch back to the on-screen control mode,
and then you can control play on this system.
• :Tap to access the music menu.
Search for a track
You can select a track quickly through the music menu.
1 Tap to access the music menu.
2 Tap to select a category.
» Tracks under the selected category are listed.
3 Tap a track name to start play.
• If one or more subcategories are under the
selected category, select a category rst.
ChargeyouriPod/iPhone
Once the iPod/iPhone is connected and recognized, the iPod/
iPhone begins to charge.
10 Adjust sound
When you listen to radio, enjoy music, or watch video, follow
the instructions below to adjust sound.
Adjust the volume level
Press +/- repeatedly on the front panel.
• +: Increase the volume level.
• -: Decrease the volume level.
Mute sound
Press on the front panel.
• To release the speakers from mute status, press
again.
11 Others
Playexternalaudio/videoinput
You can connect an external audio/video player to this
system.
1 Connect a composite AV cable to
• the AV-IN socket on the front panel, and
• the audio and video output sockets of the
external player.
2 Tap > to access the full menu with all feature
icons displayed.
3 Tap [AV-IN 1] to display the playback interface.
4 Operate on the external player to start play (see the
user manual of the external device).
Tip
•If you connect this system to an external player through
the VIDEO IN, AV-IN L, and AV-IN R sockets on the
rear panel, tap [AV-IN2] to switch the source
instead of [AV-IN 1].

19
English
EN
Use rear monitors
If one or two monitors are connected for backseat
passengers, you can select different sources for front and
backseat passengers.
Note
•Make sure that rear monitors are correctly connected
to this system.
•Only when the multi-zone display mode is activated,
rear monitors can receive signals from the system.
•By default, the same signals are transferred to the front
and rear monitors.
•When a disc, USB storage device, SD/SDHC card, or
iPod/iPhone connected through the USB socket is
selected as the source for front zone, you cannot select
another source for rear zone.
•Only when the system is in radio mode, navigation mode,
or Bluetooth mode, you can select a source for rear zone
from disc, SD/SDHC card, USB storage device, or iPod/
iPhone connected through the USB socket.
1 Tap > to access the full menu with all feature
icons displayed.
2 Tap
R
.
» The [Rear zone] menu is displayed.
3 Tap [Mode] to enable or disable the signal transferring
to rear monitors.
• [On]: Enable the signal transferring to rear monitors.
• [Off]: Disable the signal transferring to rear monitors.
» When it is enabled, the following interface is
displayed.
4 Tap to select an available source to start play.
5 Tap [Rear speaker] to enable or disable the audio
output to rear speakers.
• [On]: Enable the audio output to rear speakers.
• [Off]: Mute rear speakers.
6 Tap to return to the previous mode.
Switch the control interfaces
When different sources are selected for front passengers and
backseat passengers, you can tap
R
to switch the control
interface for front source or rear source.
» When
R
is solidly displayed, the current control
interface is for the front source.
» When
R
blinks with and [Rear zone]
displayed, the current control interface is for the
rear source.
Use buttons on the steering wheel
You can assign a function to a button on the steering wheel,
and then control the system with that button.
1 Tap > to access the full menu with all feature
icons displayed.
2 Tap .
» The [Steering Wheel Remote Control Learning]
interface is displayed.