Philips OR2200 User manual

www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
OR2200
Question?
Contact
Philips
Question?
Contact
Philips

1EN
Contents
1 Safety 2
2 Your clock radio 3
Introduction 3
What's in the box 3
Overview of the product 4
Know about the LCD display 5
3 Forthersttimeuse 6
Assemble the AC power adaptor 6
Connect power 6
Power on 6
Adjust brightness 7
4 Settimeanddate 8
5 Usethealarmtimer 9
Set an alarm 9
Deactivate a preset alarm 9
Snooze the alarm 9
Stop the alarm 9
6 Listen to FM radio stations 10
Switch to FM mode 10
Search for a radio station automatically 10
Search for a radio station manually 10
Store radio stations automatically 10
Program radio stations manually 10
Display RDS information 11
Adjust FM settings 11
7 Listen to DAB radio stations 12
Switch to DAB mode 12
For the rst time use 12
Tune to a stored radio station 12
Program radio stations 12
Display DAB information 13
Use DAB menus 13
8 Listen to an external device 15
9 Usesystemmenus 16
Check the current software version 16
Upgrade the software 16
Reset the product 16
10 Adjustvolume 17
11 Usethesleeptimer 18
12 Usethecountdowntimer 19
13 Troubleshooting 20
14 Productinformation 21
General information 21
Tuner 21
Speakers 21
Amplier 21
15 Notice 22
Compliance 22
Care of the environment 22
Copyright 22
Contents

2EN
1 Safety
Read and understand all instructions before you
use this product. If damage is caused by failure
to follow the instructions, the warranty does
not apply.
Riskofelectricshockorre!
• Never remove the casing of the product.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer
Care to have the product checked before
use.
• Never place the product and accessories
near naked ames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
hold the plug securely, never the cable.
Riskofshortcircuitorre!
• Use only power supplies listed in the user
manual
• Before you connect the product to the
power outlet, make sure that the power
voltage matches the value printed on the
back of the product. Never connect the
product to the power outlet if the voltage
is different.
• Never expose the product to rain, water,
sunshine, or excessive heat.
• Avoid force coming onto power plugs.
Loose power plugs can cause arcing or re.
Riskofinjuryordamagetotheproduct!
• This product shall not be exposed to
dripping or splashing!
• Do not place any sources of danger on this
product (e.g. liquid lled objects, lighted
candles).
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Riskofoverheating!
• Never install this product in a conned
space. Always leave a space of at least four
inches around the product for ventilation.
• Make sure that curtains or other objects
never cover the ventilation slots on the
product.
Note
•The rated power voltage is printed on the back of the
product.The model number and serial number are
printed on the bottom.

3EN
2 Your clock radio
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this product, you can:
• listen to FM radio stations (RDS
supported),
• listen to DAB radio stations,
• listen to an external device through the
AUDIO IN socket, and
• wake up to alarms.
What's in the box
Check and identify the contents of the package:
a Digital radio
b Usermanual
c AC power adaptor
d Plug converter for AC power adaptor X 2
User Manual
ORD2105

4EN
Overview of the product
a TIMER
• Press and hold to start setting
countdown timer.
b
• In standby mode, press and hold to
start setting time and date.
• In FM or DAB mode, press and hold to
access the menus.
• When listening to an RDS or DAB
station, press repeatedly to display
available information.
c SLEEP
• Press repeatedly to set the sleep timer.
d SOURCE
• Press repeatedly to select a source.
e Powerandvolumeknob
• Press to power on or off the product.
• Rotate to adjust volume.
f LCD display
g AL1/AL2
• Press and hold to start setting an alarm
timer.
• When an alarm rings, press to stop the
alarm.
a
b
c
d
e
k
j
i
h
g
f
• Press to view the alarm settings.
• Press repeatedly to deactivate or
activate the alarm timer.
h PRESET
• Press to access the list of stored radio
stations.
i /
• Press repeatedly to tune to a station.
• Press and hold to tune to the previous
or next strong station automatically.
• Press to toggle through menus or
options.
j
• Press and hold to start storing available
radio stations automatically.
• Press to conrm an option.
k SNOOZE/BRIGHTNESS
• Press to adjust the brightness of LCD
display.
• When an alarm rings, press to snooze
the alarm.

5EN
Know about the LCD display
a Therstalarmisactivated.
b Thesecondalarmisactivated.
c The clock
d Textinformation
e Thesleeptimerisactivated.
f Thecountdowntimerisactivated.
g The current source
a
c
d
e
g
f
b

6EN
3 For the first
timeuse
AssembletheACpower
adaptor
1 Align the plug converter to the holes on
the power adaptor.
2 Push the plug converter downwards until
you hear a "click".
Replace a plug converter
1 Press down the clip.
2 Slide the plug converter outwards.
3 Pull the plug converter out.
4 Fix another plug converter to the power
adaptor.
Connect power
Connect the AC power adaptor between
• the DC-IN socket on the back panel,
and
• the AC power outlet.
» The product switches to standby
mode.
» [0:00] blinks.
Power on
Press the power and volume knob.
» The product is powered on and
switches to the last mode.
Switchtostandbymode
Press the power and volume knob again.
» If the clock is neither manually set nor
automatically synchronized with a DAB
radio station, [0:00] blinks.
» If the clock is manually set or
automatically synchronized with a
DAB radio station, the time and date is
displayed.

7EN
Adjust brightness
Press BRIGHTNESS repeatedly to adjust the
brightness of the LCD display.

8EN
4 Settimeand
date
Note
•To manually set the clock, switch the product to
standby mode rst.
1 In standby mode, press and hold
until [Settime] is displayed.
» The hour digits blink.
2 Press / to set the hour, and then
press to conrm.
» The minute digits blink.
3 Press / to set the minute, and then
press to conrm.
» The date is displayed with the day
digits blink.
4 Press / to set the day, and then
press to conrm.
» The month digits blink.
5 Press / to set the month, and then
press to conrm.
» The year digits blink.
6 Press / to set the year, and then
press to conrm.
» [Timesaved] ashes, and then the set
clock and date are displayed.
Tip
•When a DAB radio station that transmits time signals is
broadcast, the product synchronizes its clock with the
DAB radio station automatically.

9EN
5 Usethealarm
timer
Note
•Make sure that you have set the clock correctly.
Setanalarm
You can set two alarms.
1 Press and hold AL1 (or AL2) for two
seconds.
» [Alarm1] (or [Alarm2]) is displayed
with AL1 (or AL2) blinking.
» The current alarm time is displayed
with hour digits blinking.
2 Press / to set the hour, and then
press to conrm.
» The minute digits begin to blink.
3 Press / to set the minute, and then
press to conrm.
» The alarm source name begins to
blinks: [DAB], [FM], or [Buzzer].
4 Press / to select an alarm source,
and then press to conrm.
• If [DAB] or [Buzzer] is selected as
the alarm source, press to
select a preset radio station or the last
listened station.
» The alarm frequency blinks: [Daily]
(daily), [Weekdays] (weekdays),
[Weekends] (weekends), or [Once]
(once).
5 Press / to select a frequency, and
then press to conrm.
» The alarm volume level blinks.
6 Press / to select the volume level,
and then press to conrm.
» [AlarmSaved] ashes.
Deactivateapresetalarm
1 Press AL1 (or AL2) to view alarm settings.
2 Press AL1 (or AL2) again.
» [Alarm1] (or [Alarm2]) and [On] is
displayed.
3 Press AL1 (or AL2) repeatedly to select
[On] or [Off].
• [On]:The preset alarm is activated.
• [Off]:The preset alarm is deactivated.
» AL1 (or AL2) is displayed when the
preset alarm is activated.
» AL1 (or AL2) disappears when the
preset alarm is deactivated.
Snoozethealarm
When an alarm sounds, press SNOOZE.
» The alarm repeats after 9 minutes.
Stopthealarm
When the rst (or second) alarm sounds, press
AL1 (or AL2).
» The alarm stops and then repeats at
the set time.

10 EN
6 Listen to FM
radio stations
Note
•For optimal reception, fully extend the antenna and
adjust its position.
•You can store a maximum of 20 FM radio stations.
SwitchtoFMmode
Press SOURCE repeatedly until [FM Mode] is
displayed.
» FM is highlighted.
» The current frequency is displayed.
Search for a radio station
automatically
Press and hold / until [Scanning...] is
displayed.
» After a strong radio station is detected,
the search stops and the radio station
is broadcast.
Search for a radio station
manually
Press / repeatedly until the frequency of
target radio station is displayed.
Store radio stations
automatically
Press and hold until [Auto] is
displayed.
» After the search is complete, the rst
stored radio station is broadcast.
• To tune to a stored radio station, press
PRESET to access the list of stored radio
stations, and then press / repeatedly.
Programradiostations
manually
1 Tune to a radio station.
2 Press and hold PRESET until [Preset
store] is displayed.
3 Press / repeatedly to select a preset
sequence number.
4 Press PRESET to conrm.
» The radio station is stored with the
selected sequence number.
5 Repeat steps 1-4 to program more radio
stations.
• To tune to a stored radio station, press
PRESET to access the list of stored radio
stations, and then press / repeatedly.
Note
•If you store a radio station with the sequence number
of another one, the earlier one is overwritten.

11EN
DisplayRDSinformation
Radio Data System (RDS) is a service that
allows FM stations to transmit additional
information.When you tune to an FM radio
station that transmits RDS signals, the station
name is displayed.
1 Tune to an RDS station.
2 Press repeatedly to scroll
through the following information (if
available):
• Station name
• Radio text
• Program type such as [NEWS] (news),
[SPORT] (sport), [POP M] (pop
music)...
• Stereo/Mono
RDSprogramtypes
NO TYPE No RDS programme type
NEWS News services
AFFAIRS Politics and current affairs
INFO Special information programs
SPORT Sports
EDUCATE Education and advanced training
DRAMA Radio plays and literature
CULTURE Culture, religion and society
SCIENCE Science
VARIED Entertainment programs
POP M Pop music
ROCK M Rock music
MOR M Light music
LIGHT M Light classical music
CLASSICS Classical music
OTHER M Special music programs
WEATHER Weather
FINANCE Finance
CHILDREN Children’s programs
SOCIAL Social Affairs
RELIGION Religion
PHONE IN Phone In
TRAVEL Tr ave l
LEISURE Leisure
JAZZ Jazz Music
COUNTRY Country Music
NATION M National Music
OLDIES Oldies Music
FOLK M Folk Music
DOCUMENT Documentary
TES Alarm Test
ALARM Alarm
Adjust FM settings
1 Press and hold to access the FM
menu.
2 Press / to display the [Scan setting]
menu.
3 Press to access sub-menus.
4 Press / to select an option.
• [Strong stations]: Search for strong
stations only.
• [All stations]: Search for all stations no
matter whether the signal strength of a
station is strong or weak.
5 Press to conrm the option.

12 EN
7 Listen to DAB
radio stations
Note
•For optimal reception, fully extend the antenna and
adjust its position.
•You can program a maximum of 20 DAB radio stations.
•Check with local retailer or go to www.WorldDAB.org
for applicable DAB radio frequencies in your area.
SwitchtoDABmode
Press SOURCE repeatedly until [DAB Mode]
is displayed.
» DAB is highlighted.
Forthersttimeuse
1 Press SOURCE repeatedly to switch the
product to DAB mode.
2 Press / repeatedly until the [Full
scan] menu is displayed.
3 Press to activate the automatic
search.
» This product automatically stores radio
stations with sufcient signal strength.
» After the search is complete, the
rst stored radio station is broadcast
automatically.
4 Press / repeatedly to select a station,
and then press PRESET to start listening.
Tip
•You can re-scan to update the list of stored stations
(see 'Re-scan for stations' on page 13).
•You can tune to a station manually (see 'Tune to a
station manually' on page 13).
Aboutspecialsymbols
Some symbol may be displayed before the
name of a station.
• H:The station is one of your 10 favorite
stations.
• ?:The station is unavailable or inactive.
• :The station is a primary station with
secondary service.
• :The station is a secondary station.
Tune to a stored radio station
1 Press / repeatedly to select a station.
2 Press PRESET to start listening.
Programradiostations
1 Tune to a DAB radio station.
2 Press and hold PRESET to activate the
programming.
3 Press / repeatedly to select a preset
sequence number.
4 Press PRESET to conrm.
» The radio station is stored with the
selected sequence number.
5 Repeat steps 1-4 to program more radio
stations.
• To tune to a stored radio station, press
PRESET to access the list of stored radio
stations, and then press / repeatedly.

13EN
Note
•If you store a radio station with the sequence number
of another one, the earlier one is overwritten.
DisplayDABinformation
The name of current DAB station is displayed.
You can also view the other information.
To cycle through available information, press
repeatedly.
• Dynamic label segment (DLS)
• Signal strength
• Program type (PTY)
• Ensemble name
• Frequency
• Signal error rate
• Bitrate codec
UseDABmenus
1 Press and hold to access the
DAB menus.
2 Press / repeatedly to toggle through
the menus.
Re-scan for stations
Full scan is used to perform a wide range
search for DAB radio stations.
Press to start scanning for available
DAB stations.
» After the scanning is complete, the rst
stored station is broadcast.
Tunetoastationmanually
With this feature, you can tune to a specic
channel/frequency manually. In addition to
antenna orientation for better radio reception,
the optimal reception can also be obtained with
this feature.
1 Press to access the station list.
2 Press / repeatedly to select a station
from 5A to 13F.
3 Press to conrm the option.
DRC(DynamicRangeControl)
DRC adds or removes a degree of
compensation for the differences in the dynamic
range between radio stations.
1 Press to access the sub-menus.
2 Press / repeatedly to select an
option. (The asterisk behind the option
indicates the current setting.)
• [DRC off]: No compensation applied.
• [DRC low]: Medium compensation
applied.
• [DRC high]: Maximum compensation
applied.
3 Press to conrm the option.

14 EN
Removeinvalidstations
Some stations in the list have no service when
you travel to another area. In front of the
station name of an invalid station, a question
mark (?) is displayed.
1 Press to access the sub-menus.
2 Press / repeatedly to select an
option.
• [No]: Return to the previous menu.
• [Yes]: Remove invalid stations from the
station list.
3 Press to conrm the option.
Systemmenus
1 Press to access system menus.
2 Press / repeatedly to select a sub-
menu.
• For details, refer to the section 'Use
systemmenus'.

15EN
8 Listen to an
external device
You can also listen to an external audio device,
for example, MP3 player, through this product.
1 Press SOURCE repeatedly to switch the
source to [AUX IN].
» AUX is highlighted.
2 Connect an audio input cable with a 3.5
mm connector on both ends to
• the AUDIO-IN socket on the back
panel of this product, and
• the headphone socket on the external
device.
3 Play audio on the external device (refer to
its user manual).

16 EN
9 Usesystem
menus
Use the system menus to
• check the version of current software of
this product,
• upgrade the software, and
• reset the product to factory default status.
Check the current software
version
Press to display the version of
current software.
Upgrade the software
1 Go to www.philips.com/support.
2 Search for support information about
your product with "OR2200/10" or
"OR2200M/10" as the keyword.
» When an upgrade packet is available,
the link of "FirmwareUpgrade
ReadmeFile" is accessible.The exact
wording of this link name may vary in
different languages.
3 Click the link of "FirmwareUpgrade
ReadmeFile".
4 Read and understand the instructions on
software upgrade.
5 Follow the instructions to complete the
upgrade.
Reset the product
1 Press to display the options.
2 Press / repeatedly to select an
option.
• [No]: Return to the previous menu.
• [Yes]: Reset the product to factory
default status.
3 Press to conrm the option.

17EN
10Adjustvolume
• To increase the volume, turn the power
and volume knob clockwise.
• To decrease the volume, turn the power
and volume knob anti-clockwise.

18 EN
11 Use the sleep
timer
You can set a time period after which
the product switches to standby mode
automatically.
Press SLEEP repeatedly to select a time period
(in minutes).
» When the sleep timer is activated,
appears.
» After the set period, the product
switches to standby mode.
• To deactivate the sleep timer, press
SLEEP repeatedly until [Sleep off]
appears.