Philips AJ6110 User manual

Kitchen CD Clock Radio AJ6110
AJ6111
Quick Start Guide
Preparation
Connect it
Mount it
Use it
For detailed operation of all the features, please also read the
User manual.
4
3
2
1
What’s in the box
POWER
CD
VOL
PRESET
MUTE
RADIO
Kitchen CD Clock
Radio
Remote control
with 1 x CR2025
battery
4 x spacers
Quick start guide
Mounting
template
User manual
8 x screws
What else you'll need
These tools (not included) will help you mount the unit as described in part 3 Mount it, and on the
template.
Preparation
For best performance, install the unit as far as
possible from sources of noise and interference
(e.g. fridges, microwaves, fluorescent lamps)
aFind a mounting location near a wall outlet.
bUse the mounting template to test the design and
thickness your kitchen cabinet bottom.
cBefore you decide where and how to place your unit,
try the following connections.
( See below)
Connect it
aFor memory back-up power supply,insert 1 x 9V
battery (preferably alkaline, not supplied)
with the correct polarity
bConnect the AC power cord to the wall socket.
2
Electric drill Ta pe measure Scissors
Sellotape Screwdriver Safety goggles
W
1
a
Template
b
2
2006 © Koninklijie Philips Electronics N.V. All rights reserved.
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA P.O. Box
671539, Marietta, GA. 30006-0026
http://www.philips.com AL-0608
1 x 9V
battery
Tip
We recommend you insert a 9V
battery for memory back-up
power supply. In the event of a
power interruption, this will help
safeguard the clock, timer settings
and preset radio stations.To save
energy, the display switches off
and you will not be able to oper-
ate the CD/ Tuner functions.
To prevent obstruction or
danger, use the power cord posts
to wrap the power cord so that
excess cord does not hang down.
To reduce the risk of fire,
do not place any heating or
cooking apparatus beneath
this unit.
AJ6110 QSG-Eng 3/6/2006 10:53 Page 1
All manuals and user guides at all-guides.com
all-guides.com

Kitchen CD Clock Radio AJ6110
AJ6111
Quick Start Guide
Preparation
Connect it
Mount it
Use it
For detailed operation of all the features, please also read the
User manual.
4
3
2
1
What’s in the box
POWER
CD
VOL
PRESET
MUTE
RADIO
Kitchen CD Clock
Radio
Remote control
with 1 x CR2025
battery
4 x spacers
Quick start guide
Mounting
template
User manual
8 x screws
What else you'll need
These tools (not included) will help you mount the unit as described in part 3 Mount it, and on the
template.
Preparation
For best performance, install the unit as far as
possible from sources of noise and interference
(e.g. fridges, microwaves, fluorescent lamps)
aFind a mounting location near a wall outlet.
bUse the mounting template to test the design and
thickness your kitchen cabinet bottom.
cBefore you decide where and how to place your unit,
try the following connections.
( See below)
Connect it
aFor memory back-up power supply,insert 1 x 9V
battery (preferably alkaline, not supplied)
with the correct polarity
bConnect the AC power cord to the wall socket.
2
Electric drill Ta pe measure Scissors
Sellotape Screwdriver Safety goggles
W
1
a
Template
b
2
2006 © Koninklijie Philips Electronics N.V. All rights reserved.
PHILIPS CONSUMER ELECTRONICS NORTH AMERICA P.O. Box
671539, Marietta, GA. 30006-0026
http://www.philips.com AL-0608
1 x 9V
battery
Tip
We recommend you insert a 9V
battery for memory back-up
power supply. In the event of a
power interruption, this will help
safeguard the clock, timer settings
and preset radio stations.To save
energy, the display switches off
and you will not be able to oper-
ate the CD/ Tuner functions.
To prevent obstruction or
danger, use the power cord posts
to wrap the power cord so that
excess cord does not hang down.
To reduce the risk of fire,
do not place any heating or
cooking apparatus beneath
this unit.
AJ6110 QSG-Eng 3/6/2006 10:53 Page 1
All manuals and user guides at all-guides.com

Mount it
Ask a friend to help out. An extra hand to hold
the unit makes mounting easier and quicker
A
•Cut the template to fit inside the cabinet.
•Align the template border marked "FRONT" along the
front edge of your cabinet.
•Use adhesive tape to fix the template.
•Drill 1/4 inch holes, as marked Xon the template.
•Remove the template when you finish drilling.
B
Using the spacers
On the spacers, there are 4 pairs of notch length
options. Depending on the thickness of you cabinet bot-
tom (with/ without an overhang), these notch lengths
correspond to the 4 notch height in the space holders,
and allow you to adjust to the best height to help you
mount the unit.
•Measure the height of the cabinet bottom and/over-
hang.
•Tu rn the spacer counterclockwise to determine
which of the 4 heights is most suitable: Low • •
High. Align to the arrow indication.
•Insert the spacers accordingly.
3
Template
A
Tip
– Clean the bottom of the cabinet surface and also empty your cabinet before mounting.
– Place the unit in a clean, safe place when drilling to avoid wood shavings dropping into the
ventilation slots.
– Use a nail to start each drill hole.
– Drill from the bottom upwards if you do not have enough room inside the cabinet.
– Hold your drill firmly at 90owith the cabinet bottom and drill holes at low speed.
– Clear wood shavings.
C
•Manually fasten the 4long screws down into the spacer holder holes to mount your set. Start
screwing at opposite corners of the unit for better support.
C
Tip
To prevent damage to your
set, do not use an electric
drill to secure screws when
mounting!
– If the overhang is more than 1 1/4 inch, use
longer screws (not included).
Use it
For full details, please read and follow the instructions inside the User manual.
A
Setting the clock
1On the set, press and hold CLOCK.
➜The hour digits start flashing (AM 12:00 by default).
2Hold down or press ∞or §repeatedly to set the hour.
3Press CLOCK to confirm the setting.
➜The minute digits start flashing.
4Repeat step 3to set the minute.
5Press CLOCK to confirm the setting.
To turn on the Daylight Saving Time (DST) mode
1In the standby mode, press and hold DISP on the set.
➜Current time setting moves ahead by 1 hour.
DST appears.
2Press DISP again.
➜The set returns to normal time setting. DST disappears.
B
Setting the timer
1On the set, press TIMER to activate.
➜015 flashes. TIMER appears
2Tu r n the TIMER control counter-/clockwise to
adjust your timer period (from 1 to 180 minutes).
➜Display shows selected timer period.
3Press TIMER to confirm.
➜Timer period starts to count down. TIMER flashes
4To cancel the timer, press TIMER during the countdown.
➜Display shows the clock time.
4C
Playing discs
1Press POWER to on, then press CD/AM/FM
once or more to select CD source.
2Press 0EJECT to open the CD compartment
3Insert a disc with the printed side facing up.
Press 0again to close the compartment
➜Playback starts automatically. Display shows
current track number
4To pause playback, pressÉÅ.To resume playback,
press the button again
5To stop playback, pressÇ
➜Display shows the total number of tracks
D
Tuning to radio stations
1Press POWER to on, then press then press
CD/AM/FM once or more to select radio source
(AM or FM)
2Press and hold ∞/ §until the frequency in the
display starts running
➜The radio automatically tunes to a station of
sufficient reception
3Repeat step 2if necessary until you find the desired
radio station
➜To tune to a weak station, press ∞/ §briefly
and repeatedly until optimal reception is found
MCM760 MICRO SYSTEM
MP3-CD/CD-R/CD
-RW COMPATIBLE
MICRO SYSTEM
Tip
To Improve radio reception:
– For FM, extend and adjust the AC power cord
H
L
Spacer
L (Low)
L••H (4 heights)
Arrow
B
AJ6110 QSG-Eng 3/6/2006 10:53 Page 2
All manuals and user guides at all-guides.com

Mount it
Ask a friend to help out. An extra hand to hold
the unit makes mounting easier and quicker
A
•Cut the template to fit inside the cabinet.
•Align the template border marked "FRONT" along the
front edge of your cabinet.
•Use adhesive tape to fix the template.
•Drill 1/4 inch holes, as marked Xon the template.
•Remove the template when you finish drilling.
B
Using the spacers
On the spacers, there are 4 pairs of notch length
options. Depending on the thickness of you cabinet bot-
tom (with/ without an overhang), these notch lengths
correspond to the 4 notch height in the space holders,
and allow you to adjust to the best height to help you
mount the unit.
•Measure the height of the cabinet bottom and/over-
hang.
•Tu rn the spacer counterclockwise to determine
which of the 4 heights is most suitable: Low • •
High. Align to the arrow indication.
•Insert the spacers accordingly.
3
Template
A
Tip
– Clean the bottom of the cabinet surface and also empty your cabinet before mounting.
– Place the unit in a clean, safe place when drilling to avoid wood shavings dropping into the
ventilation slots.
– Use a nail to start each drill hole.
– Drill from the bottom upwards if you do not have enough room inside the cabinet.
– Hold your drill firmly at 90owith the cabinet bottom and drill holes at low speed.
– Clear wood shavings.
C
•Manually fasten the 4long screws down into the spacer holder holes to mount your set. Start
screwing at opposite corners of the unit for better support.
C
Tip
To prevent damage to your
set, do not use an electric
drill to secure screws when
mounting!
– If the overhang is more than 1 1/4 inch, use
longer screws (not included).
Use it
For full details, please read and follow the instructions inside the User manual.
A
Setting the clock
1On the set, press and hold CLOCK.
➜The hour digits start flashing (AM 12:00 by default).
2Hold down or press ∞or §repeatedly to set the hour.
3Press CLOCK to confirm the setting.
➜The minute digits start flashing.
4Repeat step 3to set the minute.
5Press CLOCK to confirm the setting.
To turn on the Daylight Saving Time (DST) mode
1In the standby mode, press and hold DISP on the set.
➜Current time setting moves ahead by 1 hour.
DST appears.
2Press DISP again.
➜The set returns to normal time setting. DST disappears.
B
Setting the timer
1On the set, press TIMER to activate.
➜015 flashes. TIMER appears
2Tu r n the TIMER control counter-/clockwise to
adjust your timer period (from 1 to 180 minutes).
➜Display shows selected timer period.
3Press TIMER to confirm.
➜Timer period starts to count down. TIMER flashes
4To cancel the timer, press TIMER during the countdown.
➜Display shows the clock time.
4C
Playing discs
1Press POWER to on, then press CD/AM/FM
once or more to select CD source.
2Press 0EJECT to open the CD compartment
3Insert a disc with the printed side facing up.
Press 0again to close the compartment
➜Playback starts automatically. Display shows
current track number
4To pause playback, pressÉÅ.To resume playback,
press the button again
5To stop playback, pressÇ
➜Display shows the total number of tracks
D
Tuning to radio stations
1Press POWER to on, then press then press
CD/AM/FM once or more to select radio source
(AM or FM)
2Press and hold ∞/ §until the frequency in the
display starts running
➜The radio automatically tunes to a station of
sufficient reception
3Repeat step 2if necessary until you find the desired
radio station
➜To tune to a weak station, press ∞/ §briefly
and repeatedly until optimal reception is found
MCM760 MICRO SYSTEM
MP3-CD/CD-R/CD
-RW COMPATIBLE
MICRO SYSTEM
Tip
To Improve radio reception:
– For FM, extend and adjust the AC power cord
H
L
Spacer
L (Low)
L••H (4 heights)
Arrow
B
AJ6110 QSG-Eng 3/6/2006 10:53 Page 2
All manuals and user guides at all-guides.com