Philips DC320/98 User manual

Register your product and get support at
www.philips.com/welcome
EN User manual 3
ZH-TW 使用手冊 17
DC320

3
English
EN
7 Adjust sound 14
Adjust volume level 14
Mute sound 14
Select a preset sound effect 14
Enhance bass 14
8 Product information 15
Specications 15
9 Troubleshooting 16
Contents
1 Important 4
Safety 4
Notice 5
2 Your Docking Entertainment System 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
Overview of the remote control 8
3 Get started 9
Connect power 9
Set time and date 10
Turn on 10
4 Play 11
Play from iPod/iPhone 11
Play from an external device 11
5 Listen to radio 12
Tune to a radio station 12
Program radio stations automatically 12
Program radio stations manually 12
Select a preset radio station 12
6 Other features 13
Set the alarm timer 13
Set the sleep timer 13
Adjust display brightness 14

4
m Referallservicingtoqualiedservice
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
nBattery usage CAUTION – To prevent
battery leakage which may result in
bodily injury, property damage, or
damage to the unit:
Install all batteries correctly, + and -•
as marked on the unit.
Do not mix batteries (old and new•
or carbon and alkaline, etc.).
Remove batteries when the unit is•
not used for a long time.
The batteries shall not be exposed•
to excessive heat such as sunshine,
reorthelike.
oApparatus shall not be exposed to
dripping or splashing.
pDo not place any sources of danger on
theapparatus(e.g.liquidlledobjects,
lighted candles).
qThis product may contain lead and
mercury. Disposal of these materials
may be regulated due to environmental
considerations. For disposal or recycling
information, please contact your local
authorities or the Electronic Industries
Alliance: www.eiae.org.
rWhere the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain
readily operable.
1 Important
Safety
Important Safety Instructions
aRead these instructions.
bKeep these instructions.
cHeed all warnings.
dFollow all instructions.
eDo not use this apparatus near water.
fClean only with dry cloth.
gDo not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
hDo not install near any heat sources
such as radiators, heat registers, stoves,
orotherapparatus(includingampliers)
that produce heat.
iProtect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
jOnly use attachments/accessories
speciedbythemanufacturer.
kUse only with the cart,
stand, tripod, bracket,
ortablespeciedby
the manufacturer or
sold with the apparatus.
When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-
over.
lUnplug this apparatus during lightning
storms or when unused for long periods
of time.
EN

5
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection
of electrical and electronic products and
batteries. The correct disposal of these
products helps prevent potentially negative
consequences on the environment and human
health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment
and human health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
Warning
Never remove the casing of this apparatus.•
Never lubricate any part of this apparatus.•
Never place this apparatus on other electrical•
equipment.
Keep this apparatus away from direct sunlight,
•
nakedamesorheat.
Ensure that you always have easy access to the
•
power cord, plug or adaptor to disconnect the
apparatus from the power.
Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and
old equipment.
English
EN

6
What’s in the box
Check and identify the contents of your
package:
Main unit•
Remote control•
1 x AC adaptor, GFP241DA-1220-1•
(Philips)
1 x MP3 link cable•
User manual•
Quick start guide•
2 Your Docking
Entertainment
System
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this unit, you can enjoy audio from the
iPod, iPhone, other audio devices, or the radio.
The radio, iPod, or iPhone can be set as the
alarm timer.You can set two alarm timers to go
off at different time.
EN

7
/
Skiptotheprevious/nextaudiole.•
Searchwithinanaudiole.•
Select a preset radio station.•
Adjust time.•
giPod/iPhone dock
Load an iPod/iPhone.•
hPOWER
Turn on the unit or switch to•
standby mode.
Deactivate the sleep timer.•
Stop alarm.•
iSLEEP
Set the sleep timer.•
jSOURCE
Select a source: iPod/iPhone, FM•
tuner or MP3 link.
kMUTE
Mute/unmute sound.•
Overview of the main unit
aREPEAT ALARM/BRIGHTNESS
CONTROL
Repeat the alarm.•
Adjust the display brightness.•
bALM 1/ALM 2
Set the alarm timer.•
Turn off the alarm tone.•
View alarm settings.•
cDISPL AY
View the clock time and date.•
dAUTO SCAN/TIME SET
Set the clock.•
Program radio stations.•
eTUNING +/-
Tune to a radio station.•
Adjust time.•
f
Start or pause iPod/iPhone play.•
VOL
VOL
English
EN

8
Overview of the remote
control
aPOWER
Turn on the unit or switch to•
standby mode.
Stop alarm.•
Deactivate the sleep timer.•
biPhone/iPod
Select iPhone or iPod source.•
cPRESET +/-
Select a preset radio station.•
Scroll through the iPod/iPhone•
menu.
d/
Skiptotheprevious/nextaudiole.•
Searchwithinanaudiole.•
Adjust time.•
VOL +/-
Adjust volume.•
lDisplay panel
Show current status.•
mDSC
Select a preset sound setting.•
nDBB
Turn on or off dynamic bass•
enhancement.
oMP3-LINK
Jack for an external audio device.•
pDC IN
Power supply socket.•
qFM antenna
Improve FM reception.•
EN

9
3 Get started
Caution
Use of controls or adjustments or•
performance of procedures other than herein
may result in hazardous radiation exposure or
other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
rear of the apparatus.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect power
Caution
Risk of product damage! Ensure that the power•
voltage corresponds to the voltage printed on
the back or underside of the apparatus.
Risk of electric shock! When you unplug the
•
AC adaptor, always pull the plug from the
socket. Never pull the cord.
Before connecting the AC adaptor, ensure you
•
have completed all other connections.
Note
The type plate is located on the rear of the•
main unit.
1Prepare the AC power adaptor.
eOK/
Start or pause iPod/iPhone play.•
Conrmselection.•
fMP3 LINK
Select external audio device source.•
gMENU
Select the iPhone/iPod menu.•
hSLEEP
Set the sleep timer.•
iDBB
Turn on or off dynamic bass•
enhancement.
jDSC
Select a preset sound setting.•
kALM 1/ALM 2
Set the alarm timer.•
Turn off the alarm tone.•
View alarm settings.•
lVOL +/-
Adjust volume.•
mBRIGHTNESS/REP ALM
Adjust the display brightness.•
Repeat the alarm.•
nMUTE
Mute volume.•
oSET TIME/PROG
Set the clock.•
Program radio stations.•
pTUNER
Select tuner source.•
English
EN

10
Tip
In 12 hour format, [MONTH--DAY] is•
displayed.
in 24 hour format, [DAY--MONTH] is
•
displayed.
Turn on
1Press POWER.
The unit switches to the last selected»
source.
Switch to standby
1Press POWER again to switch the unit to
standby mode.
The time and date (if set) appear on»
the display panel.
2Connect one end of the AC adaptor to
the DC IN socket on the main unit.
3Connect the other end of the AC
adaptor to the wall outlet.
Set time and date
1In standby mode, press and hold SET
TIME/PROG for 2 seconds.
[24 HR] begins to blink.»
2Press / to select 12/24 hour format.
3Press SET TIME/PROGtoconrm.
The hour digits begin to blink.»
4Press / to set the hour.
5Press SET TIME/PROGtoconrm.
The minute digits begin to blink.»
6Repeat steps 4-5 to set the minute, year,
month, and day.
EN

11
To go back to previous iPod/iPhone•
menu, press MENU. To scroll
through the menu, press PRESET
+/-.Toconrmaselection,press
OK/.
If no key is pressed for more than»
10 seconds, OK/acts back as
the play/pause key.
Charge the iPod/iPhone
When the unit is connected to power, the
docked iPod/iPhone begins to charge.
Tip
For certain iPod models, it may take up to a•
minute before the charging indication appears.
Play from an external device
You can also listen to an external audio device
through this unit.
1Press SOURCE repeatedly to select MP3
link source.
2Connect the supplied MP3 link cable to:
the• MP3 LINK jack (3.5mm) on the
back of the unit.
the headphone jack on an external•
device.
3Start to play the device (see the device
user manual).
4 Play
Play from iPod/iPhone
You can enjoy audio from iPod/iPhone through
this unit.
Compatible iPod/iPhone
Apple iPod and iPhone models with a 30-pin
dock connector:
iPod classic, iPod touch, iPod nano, iPod•
5th generation (video), iPod with color
display, iPod mini.
iPhone, iPhone 3G.•
Listen to the iPod/iPhone
1Place the iPod/iPhone into the dock.
2Press SOURCE repeatedly to select iPod/
iPhone source.
The connected iPod/iPhone plays»
automatically.
To pause/resume play, press• .
To skip to a track, press• / .
To search during play, press and•
hold / , then release to resume
normal play.
English
EN

12
Program radio stations
automatically
You can program a maximum of 20 preset
radio stations.
1In the tuner mode, press and hold SET
TIME/PROG for more than 2 seconds to
activate automatic program mode.
[AUTO] (auto) is displayed.»
All available stations are programmed»
in the order of waveband reception
strength.
Therstprogrammedradiostationis»
broadcast automatically.
Program radio stations
manually
You can program a maximum of 20 preset
radio stations.
1Tune to a radio station.
2Press SET TIME/PROG to activate the
program mode.
3Press PRESET +/- to select a number.
4Press SET TIME/PROGtoconrm.
5Repeat the above steps to program other
stations.
Tip
To overwrite a programmed station, store•
another station in its place.
Select a preset radio station
1Press PRESET +/- to select a preset
number.
5 Listen to radio
Note
Only FM radio reception is available on this•
unit.
Tune to a radio station
Tip
Position the antenna as far as possible from•
TV, VCR or other radiation source.
Note
For optimal reception, fully extend and adjust•
the position of the antenna.
1Press TUNER to select FM tuner.
2Press and hold / on the remote
control for more than 2 seconds.
[Srch] (search) is displayed.»
The radio tunes to a station with»
strong reception automatically.
3Repeat step 2 to tune to more stations.
To tune to a weak station, press•
/repeatedlyuntilyoundoptimal
reception.
EN

13
Activate and deactivate the alarm
timer
1Press ALM 1 or ALM 2 repeatedly to
activate or deactivate the timer.
If the timer is activated, [»AL 1] or
[AL2] is displayed.
If the timer is deactivated, [»AL1] or
[AL2] disappears.
Repeat alarm
1When the alarm rings, press
BRIGHTNESS/REP ALM.
The alarm repeats ringing minutes later.»
Tip
You can press•/ to adjust the interval to
repeat alarm.
Stop alarm ring
1When the alarm rings, press the
corresponding ALM 1 or ALM 2.
The alarm stops but the alarm settings»
remain.
View the alarm settings
1Press ALM 1 or ALM 2.
Set the sleep timer
This unit can switch to standby automatically
after a set period of time.
1Press SLEEP repeatedly to select a set
period of time (in minutes).
When the sleep timer is activated, the»
display shows , and the volume will
gradually decrease.
6 Other features
Set the alarm timer
You can set two alarms which go off at different
time.
1Ensure that you have set the clock
correctly.
2Press and hold ALM 1 or ALM 2 for 2
seconds.
[AL 1] or [AL 2] begin to blink.»
3Press SOURCE to select an alarm sound
source: iPod/iPhone, iPod/iPhone playlist,
FM tuner, or buzzer.
4Press ALM 1 or ALM 2.
Hour digits begin to blink.»
5Press / repeatedly to set the hour.
6Press ALM 1 or ALM 2toconrm.
Minute digits begin to blink.»
7Repeat steps 5-6 to set the minute.
8Repeat steps 5-6 to select whether to
ring alarm the whole week, on weekdays,
or at weekend.
9Repeat steps 5-6 to set the alarm volume.
Tip
If you set iPhone/iPod playlist as the sound•
source, you must create a playlist in iTunes
called “PHILIPS” and import it to your iPhone/
iPod.
If no playlist is created in the iPod/iPhone or
•
there is no song in the playlist, the unit will
wake to songs in the iPod/iPhone.
English
EN

14
7 Adjust sound
Adjust volume level
1During play, press VOL +/- to increase/
decrease the volume level.
Mute sound
1During play, press MUTE to mute/unmute
sound.
Select a preset sound effect
1During play, press DSC repeatedly to
select:
[POP] (pop)•
[JAZZ] (jazz)•
[CLAS] (classic)•
[ROCK] (rock)•
Enhance bass
1During play, press DBB to turn on or off
dynamic bass enhancement.
If DBB is activated, [DBB] is displayed.»
To deactivate sleep timer
1Press SLEEP repeatedly until [SLP OFF]
(SLP off ) is displayed.
When the sleep timer is deactivated,»
disappears on the display.
Adjust display brightness
1Press BRIGHTNESS/REP ALM
repeatedly to select different levels of
display brightness.
EN

15
General information
AC power
(power adaptor)
Input: 100-240 V~,
50-60 Hz, 0.55 A
Output: 12V 2A
Operation Power
Consumption 10 W
Standby Power
Consumption <2 W
Dimensions
- Main Unit
(W x H x D)
173 x185 x 144 mm
Weight
- Main Unit 0.66 kg
8 Product
information
Note
Product information is subject to change•
without prior notice.
Specications
Amplier
Rated Output Power 2 x 6 W RMS
Frequency Response 125 Hz - 16 kHz,
±3 dB
Signal to Noise Ratio >55 dB
MP3 link 500 mV RMS
10 kohm
Tuner
FM
Tuning Range 87.5 - 108 MHz
Tuning grid 50 KHz
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBu
<45 dBu
Search Selectivity <36 dBu
Total Harmonic
Distortion <3%
Signal to Noise Ratio >45 dB
English
EN

16
Clock/timer setting erased
Power has been interrupted or the power•
plug has been disconnected.
Reset the clock/timer.•
9 Troubleshooting
Warning
Never remove the casing of this apparatus.•
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome).When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
Ensure that the AC power plug of the•
unit is connected properly.
Ensure that there is power at the AC•
outlet.
No sound
Adjust the volume.•
No response from the unit
Disconnect and reconnect the AC power•
plug, then turn on the unit again.
Poor radio reception
Increase the distance between the unit•
and your TV or VCR.
Fully extend the FM antenna.•
Timer does not work
Set the clock correctly.•
Switch on the timer.•
EN