Philips SL ParBlazer 100 UV Instruction Manual

SL ParBlazer 100 UV

SL ParBlazer 100 UV Installation & User’s Manual
Version as of: 9th Mar, 2015 Rev1.0
2015 Philips Group. All rights reserved.
Showline Offices
Showline - Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Showline - Europe
Marssteden 152
Enschede 7547 TD
The Netherlands
Tel: [phone]
Fax: [phone]
Showline - Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand U.S.A
Tel: [phone]
Fax: [phone]
Showline - Asia
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road
Kwai Chung, N.T., Hong Kong
Tel: [phone]
Fax: [phone]
Website:
www.philips.com/showline
The material in this manual is for information purposes only and is subject to change without notice. Showline assumes
no responsiblitity for any errors or omissions which may appear in this manual. For comments and suggestions regarding
corrections and/or updates to this manual, please visit the Showline website at or contact yourwww.philips.com/showline
nearest Showline office.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.
Document Number: SL ParBlazer 100 UV User’s Manual

Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org
Showline Limited Two-Year Warranty
Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the
date of delivery. A copy of the Showline two-year limited warranty containing specific terms and conditions can be
obtained by contacting your local Showline office.
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
Do not use this equipment for other than intended use.
Refer service to qualified personnel.
WARNING: You must have access to a mains circuit breaker or other power disconnect device
before installing any wiring. BE sure that power is disconnected by removing fuses or turning the
mains circuit breaker off before installation. Installing the device with power on may expose you
to dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code and local codes for cable specifications.
Failure to use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the Nation Electric
Code and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to
avoid shock or damage to the control. It is recommended that a qualified electrician perform this
installation.
Installation & User’s ManualSL ParBlazer 100 UV
IMPORTANT INOFRMATION

TABLE OF CONTENTS
Showline Offices Inside Front Cover
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
Showline Limited Two-Year Warranty
TABLE OF CONTENTS
PREFACE
About this Manual
Included Items
SL ParBlazer 100 UV OVERVIEW
SL ParBlazer 100 UV Components
INSTALLATION AND SET UP
Connecting Power
Connecting SL ParBlazer 100 UV to AC Power
Truss / Hanging Applications
Floor Mounting
Connecting to the DMX512 Network
Mounting Luminaire
OPERATION AND PROGRAMMING
LCD Display and Menu System
LCD Display and Menu System Operation
SL ParBlazer 100 UV Menu Tree
Master / Slave Operational Mode
Dimming Curve Selection
DMX CONTROL
RDM PARAMETER IDs
8-Bit Mode
16-Bit Mode
SL ParBlazer 100 UV DMX Mapping
SL ParBlazer 100 UV RDM Parameter IDs
CLEANING AND CARE
Special Cleaning and Care Instructions
Front Lens Cleaning
Service and Maintenance
TECHNICAL SPECIFICATIONS
Operational Specifications
Luminaire Dimensions
Table of contents
2
1
1
1
3
3
4
5
5
8
8
7
8
9
10
11
12
13
14
14
14
15
18
18
18
19
20

PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
Please read all instructions before installing or using this product. Retain this manual for future reference.
Additional product information and descriptions may be found on the product specification sheet.
Note: The SL ParBlazer 100 UV luminaire works from 100 to 240 VAC (auto-ranging).
2. Included Items
Each SL ParBlazer 100 UV luminaire includes the following items:
SL ParBlazer 100 UV Luminaire
SL ParBlazer 100 UV Luminaire
Quick Start Guide
3
About this Manual
Installation & User’s ManualSL ParBlazer 100 UV
SL ParBlazer 100 UV Luminaire

SL ParBlazer 100 UV Overview
4
1.SL ParBlazer 100 UV COMPONENTS
Common Luminaire Components
LCD Display / Menu System
Front of Unit
Rear of Unit
UV LEDs
Yoke
Tilt Knob
LCD Display / Menu System
SL ParBlazer 100 UV OVERVIEW
Safety Cable
Anchor Point
Figure 1: SL ParBlazer 100 UV Common Components
Installation & User’s Manual
DMX512/
AC Input
RDM Input
DMX512 /
AC Output
RDM Output
Figure 2: LCD Display & Menu System
Note: For Menu operation and programming details, refer to "LCD Display and Menu System" on page 9.
LEFT Arrow Button RIGHT Arrow Button
CHECK MARK(OK) Button
EXIT Button
SL ParBlazer 100 UV

5
Installation and Set Up
INSTALLATION AND SET UP
1. Power Requirements
The SL Pa rBlazer 100 UV Luminaire operates on AC input voltages from 100 to 240 VAC.
WARN ING! The SL ParBlazer 100 UV luminaire does not have an ON/OFF switch. Always disconnect power input cable
to completely remove power from the luminaire when not in use.
AC Power Operation
When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply. Each luminaire can draw up to 100 Watts.
WARN ING! Maximum amount of fixtures that may be daisy-chained is (A) 10 units 100 ~ 120VAC or (B) 23 units
230 ~ 240VAC (15 Amps).
Note: For wiring of AC input connector, refer to "Connecting SL ParBlazer 100 UV to AC Power" on page 6.
2. Connecting Power
Units can be powered in one of two ways:
Direct connection to an AC power source using an AC input cable. For wiring of the AC input connector, refer to
Connection from the AC output of another SL ParBlazer 100 UV. When using this method, it is very important not
to connect any other type of equipment device.
WARN ING! Only connect other SL ParBlazer 100 UV luminaires to the AC Output (Thru) connector of an
Installation & User’s ManualSL ParBlazer 100 UV
Table 1: SL ParBlazer 100 UVVoltage (VAC) vs. Current*
"Connecting SL ParBlazer 100 UV to AC Power" on page 6.
100 180 0.561.00
110 190 0.53 0.91
160 240 0.420.63
150 230 0.430.67
140 220 0.45 0.71
130 210 0.480.77
120 200 0.50 0.84
170 0.59
Voltage (AC) Voltage (AC)
Total Current (A) Total Current (A)
SL ParBlazer 100 UV luminaire.

Connecting SL ParBlazer 100 UV to AC Power
6
Connecting SL ParBlazer 100 UV to AC Power
Table 2 describes how to connect power to your SL ParBlazer 100 UV. Field wiring of the SL ParBlazer 100 UV
LED Luminaire is straightforward. A total of 3 wires/conductors need to be brought to the unit.
The following wiring scheme is required:
Figure 3: SL ParBlazer 100 UV AC Input & Output Connections
Luminaire
Brown Main/Line(100 to 240VAC)
Blue Neutral
Green/Yellow Ground (Earth)
Table 2: SL ParBlazer 100 UVAC Input Connections
Installation & User’s Manual
Wire Color Purpose
AC Input AC Output
SL ParBlazer 100 UV

Connecting to the DMX512 Network 7
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple SL ParBlazer 100 UVs together (up to 32 luminaires) in
"daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX connector
on the first SL ParBlazer 100 UV. Another cable runs from the other DMX connector on the first unit to a DMX
connector on the next SL ParBlazer 100 UV (or DMX512 device to be controlled).
Figure 4: SL ParBlazer 100 UV DMX512 Input / Output Connections
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1 "DMX CONTROL" on page 13. For SL ParBlazer 100 UV DMX Mapping, refer to .
Figure 5: SL ParBlazer 100 UV- DMX512 Connections
Luminaire
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next
(from console or
control device)
DMX512 Conections
Note: Remaining pins on each connector are not used.
Installation & User’s ManualSL ParBlazer 100 UV
luminaire or DMX512 controlled
device)
DMX512 Signal
Common (Drain)
DMX512-
DMX512+
XLR Pin Color
1
2
3Red
White
Black
DMX512/
RDM Input
DMX512/
RDM Output

Mounting Luminaire
8
4.Mounting Luminaire
Truss / Hanging Applications
The SL ParBlazer 100 UV is provided with the ability to hang via truss hooks, clamps, etc. (sold separately). Simply
attach hook, clamp, etc. to the SL ParBlazer 100 UV yoke in the provided M12 holes. It is recommended
(and may be required by local and national safety codes) to use and install a safety cable (sold separately) as illustrated in
Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire to allow proper, uninterrupted
airflow for cooling and movement. Refer to for spacing (dimensional) requirements."Luminaire Dimensions" on page 36
Note: Mounting hooks, clamps, safety cables, etc. are sold separately or by others. For mounting accessories
available for this product, refer to "Accessories" on page 3.
Figure 6: Mounting the Fixture - Hanging Applications
Floor Mounting
The SL ParBlazer 100 UV are designed to sit directly on its enclosure assembly (base) in a floor installation application.
When used in this type of application, be sure to leave enough space around the luminaire to allow proper, uninterrupted
airflow for cooling and movement.
Installation & User’s Manual
Safety Cable Anchor Point
Truss Hook or Clamp
(sold separately)
SAFETY CABLE: Is sold separately and
recommended for all hanging installation and
may be required by national and local codes.
Use the safety cable anchor point for this fixture.
SL ParBlazer 100 UV

OPERATION AND PROGRAMMING 9
OPERATION AND PROGRAMMING
Installation & User’s ManualSL ParBlazer 100 UV
1. LCD Display and Menu System
The SL PARBLAZER Luminaire’s LCD Display and Menu System provides local control for accessing the
following fixture’s settings:
DMX Address
Manual Dimming
Default Setting
DMX Personality
Temperature
Dimming Curve
Firmware
DMX Fail
RDM UID
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired.
Upon power up, the LCD will display the main screen showing menu. The User can use “ < ”
and “ ” to select then enter the desired function menu.
Figure 7: LCD Display and Menu System
LEFT Arrow Button RIGHT Arrow Button
CHECK MARK(OK) Button
LCD Display
EXIT Button

LCD Display and Menu System Operation
10
2.LCD Display and Menu System Operation
The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and make changes to
the menu items. When the desired menu item is reached, press the desired Menu Button to display the menu options
and to navigate and configure the menu options as required.
To navigate and access menu settings/selections:
Step 1.Make sure unit is powered and turned on.
Step 2.Press the desired button (as shown in Figure 8) to access menu categories.
Step 3.Use LEFT | RIGHT arrow buttons to navigate through the various options and settings.
Step 4.Make changes as desired.
Press the CHECK MARK (OK) button to accept changes.
Figure 8: LCD Display and Menu System
Installation & User’s Manual
LEFT Arrow Button RIGHT Arrow Button
CHECK MARK(OK) Button
EXIT Button
SL ParBlazer 100 UV

SL ParBlazer 100 UV Menu Tree 11
3. SL ParBlazer 100 UV Menu Tree
Figure 9: SL ParBlazer 100 UV Menu Tree
Installation & User’s ManualSL ParBlazer 100 UV
Temperature
Firmware
RDM UID
001--512
000%--100%
DMX 8Bit
OFF
No
DMX Address
Manual Dimming
DMX Personality
Dimming Curve
DMX Fail
Default Setting
Manual
55^oC
Linear Curve
Square Curve
Rev1.00
0x405101020304
DMX 16Bit
S_Curve
PL_Curve
Last Hold
Manual
Yes

Master / Slave Operational Mode
4.Master / Slave Operational Mode
The Master / Slave Operational Mode allows one SL ParBlazer 100 UV to act as the "Master" unit and all other
connected units are controlled by this unit. When a unit is set to "Slave" mode, it will only listen to and follow any
commands sent from a "Master" unit. Only one "Master" unit is allowed in this type of operation.
Figure 10: SL ParBlazer 100 UV- Master / Slave Configuration
Master Unit Slave Unit Slave Unit
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. "DMX CONTROL" on page 16. For SL ParBlazer 100 UV DMX Mapping, refer to
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next
(from console or
control device)
luminaire or DMX512 controlled
device)
12
Installation & User’s Manual SL ParBlazer 100 UV

5.Dimming Curve Selection
Through the menu, you are able to select one of four dimming curves:
Linear Curve
S_Curve
Square Curve
Figure 9: SL ParBlazer 100 UV Luminaire Dimmer Curves
*PL Curve follows the dimming curve of Philips Selecon PL
series LED luminaries.
DMX Value
Lumen Output
0
Linear Curve
DMX Value
Lumen Output
0
S_Curve
DMX Value
Lumen Output
0
Square Curve
DMX Value
Lumen Output
0
PL_Curve *
PL_Curve
Dimming Curve Selection 13
Installation & User’s ManualSL ParBlazer 100 UV

DMX CONTROL
DMX CONTROL
This section contains information for operating the luminaire using DMX control in 8-bit mode, 16-bit mode.
For Menu options and detailed information, see "LCD Display and Menu System” on page 9.
Note: These tables assume a DMX start address of 1. When a different starting address is used, this address becomes
channel 1 function and other functions follow in sequence.
1. SL ParBlazer 100 UV DMX Mapping
8-Bit Mode
16-Bit Mode
Table 3 provides DMX channel mapping of all DMX512 control values when the SL ParBlazer 100 UV LED
Table 4 provides DMX channel mapping of all DMX512 control values when the SL ParBlazer 100 UV LED
Luminaire is in 8-bit DMX512 mode (as set by the luminaire’s menu system).
Luminaire is in 16-bit DMX512 mode (as set by the luminaire’s menu system).
Table 3: SL ParBlazer 100 UV DMX Channel Mapping ( 8 - Bit Mode)
Table 4: SL ParBlazer 100 UV DMX Channel Mapping ( 16 - Bit Mode)
DMX
DMX
1
1
2
Parameter
Parameter
LED Intensity
LED
LED
DMX Range
DMX Range
0-255
0-255
0-255
Range
Range
0-100%
0-100%
0-100%
Defaults
Defaults
0
0
0
Description
Description
LED Intensity
Intensity Coarse
Intensity Fine
14
Installation & User’s Manual SL ParBlazer 100 UV

Model ID Manufacturer Model Description Product Category
0x1230
MSB of ESTA LSB of ESTA
Category - Network Management
Category - Status Collection
Category - RDM Information
RDM Parameter IDs Value Comment Implemented
Get Set
Allowed Allowed
Unique Seq Unique Seq Unique Seq Unique Seq
UID
Philips Entertain. Lighting Asia SL ParBlazer 100 UV 0x2030
50H 41H
0x0001
0x0020
0x0002
0x0030
0x0011
0x0033
0x0050
0x0051
0x0010
0x0032
0x0003
0x0031
0x0015
DISC_UNIQUE_BRANCH
QUEUED_MESSAGE
DISC_MUTE
STATUS_MESSAGES
DISC_UN_MUTE
STATUS_ID_DESCRIPTION
PROXIED_DEVICES
CLEAR_STATUS_ID
SUPPORTED_PARAMETERS
PARAMETER_DESCRIPTION
COMMS_STATUS
PROXIED_DEVICES_COUNT
SUB_DEVICE_STATUS_REPORT_THRESHOLD
Support required only if
supporting Parameters
beyond the minimum required set.
Support required for Manufacturer
-Specific PIDs exposed in
SUPPORTED_PARAMETERS
message.
1. SL ParBlazer 100 UV RDM Parameter IDs
The following tables outline and describe all the RDM parameters Ids associated with SL ParBlazer 100 UV LED
Luminaires.
Table 5, “SL ParBlazer 100 UV RDM Product Parameters IDs”
Table 6, “SL ParBlazer 100 UV RDM UID”
Table 7, “SL ParBlazer 100 UV RDM Parameters IDs”
Table 8, “SL ParBlazer 100 UV RDM Manufacturer IDs” on page 38
Table 9, “SL ParBlazer 100 UV RDM Manufacturer Specific PIDs” on page 38
Table 5: SL ParBlazer 100 UV RDM Product Parameters IDs
Table 6: SL ParBlazer 100 UV RDM UID
Table 7: SL ParBlazer 100 UV RDM Parameters IDs
SL ParBlazer 100 UV RDM
MSB of MSB ofLSB of LSB of
15
Installation & User’s ManualSL ParBlazer 100 UV

Table 7: SL ParBlazer 100 UV RDM Parameters IDs
Category - Product Information
Category - DMX512 Setup
Category - Sensors 0x02xx
Category - Dimmer Settings 0x03xx - FUTURE USE
Category - Power / Lamp Settings 0x04xx
Category - Display Settings 0x05xx
Category - Configuration 0x06xx
Category - Control 0x10xx
RDM Parameter IDs Value Comment Implemented
Get Set
Allowed Allowed
0x0060
DEVICE_INFO
0x00C1
BOOT_SOFTWARE_VERSION_ID
0x0121
SLOT_DESCRIPTION
0x0201
SENSOR_VALUE
0x0401
0x0601
0x0404
0x1000
0x0500
0x00C0
SOFTWARE_VERSION_LABEL
0x0120
SLOT_INFO
0x0200
SENSOR_DEFINITION
0x0400
0x0600
0x0403
0x0603
0x00B0
LANGUAGE
0x00F0
DMX_START_ADDRESS
0x00A0
LANGUAGE_CAPABILITIES
0x00E1
DMX_PERSONALITY_DESCRIPTION
0x0090
FACTORY_DEFAULTS
0x00E0
DMX_PERSONALITY
0x0082
DEVICE_LABEL
0x0081
MANUFACTURER_LABEL
0x0080
DEVICE_MODEL_DESCRIPTION
0x0070
PRODUCT_DETAIL_ID_LIST
0x00C2
BOOT_SOFTWARE_VERSION_LABLE
0x0122
DEFAULT_SLOT_VALUE
0x0202
RECORD_SENSORS
0x0402
0x0602
0x0405
0x1001
RESET_DEVICE
REAL_TIME_CLOCK
PAN_TILT_SWAP
TILT_INVERT
DISPLAY_LEVEL
LAMP_ON_MODE
DEVICE_POWER_CYCLES
PAN_INVERT
DISPLAY_INVERT
LAMP_STATE
LAMP_STRIKES
LAMP_HOURS
DEVICE_HOURS
IDENTIFY_DEVICE
0x0501
Required if device uses a DMX Slot
SL ParBlazer 100 UV RDM
16
Installation & User’s Manual SL ParBlazer 100 UV

Table 8: SL ParBlazer 100 UV RDM Parameter Status IDs
Table 8: SL ParBlazer 100 UV RDM Parameter Specific PIDs
RDM Parameter IDs Value Comment Implemented
Get Set
Allowed Allowed
0x1010POWER_STATE
0x1020PERFORM_SELFTEST
0x1030CAPTURE_PRESET
0x1021SELF_TEST_DESCRIPTION
0x1031PRESET_PLAYBACK
Manufacturer Specific messages are in the range of 0x8000 - 0xFFDF. Each Manufacturer-specific Status ID shall have a
unique meaning, which shall be consistent across all products having a given Manufacturer ID. See Table B-2, ANSI E1.20-2010
Status ID Message Value Data Value 1 Data Value 2 Status ID Description
8100H 00H 00H ALL OK
Get Set Type Length Unit Prefix Min Max Default Description
Allowed Allowed RDM Parameter IDs
1NONE NONE
DBNONE
DBNONE
100
3
3
100
0
0
8A00H U8 0DIMMER
1
8A0CH S8 0DMX FAIL MODE
1
8AA1H S8 0Dimming Curve
Category - Manufacturer Defined PIDs - Range is 0x80000-0xffdf(See ANSI E1.20-2010 Standard, Table A-3)
SL ParBlazer 100 UV RDM
Table 7: SL ParBlazer 100 UV RDM Parameters IDs
17
Installation & User’s ManualSL ParBlazer 100 UV

WARNING! All cleaning should be performed with power completely removed from the luminaire. Never remove
protective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when cleaning the
fixture. All service and maintenance, other than described herein, should be performed by a qualified technician or
Authorized Service Center.
Lint free lens tissue
Lint or powder free gloves
Reagent grade isopropyl alcohol*
A mild soap solution
If the lens is still dirty after using isopropyl alcohol, for instance if figerprints or oil is just redistributed and not
cleaned off the optic, then a mild soap and water solution can be used to gently wash the lens. Repeat the cleaning
with isopropyl alcohol to eliminate streaks and soap residue.
For all other service and maintenance issues, please contact your local Showline office or an Authorized Service
Center.
1. Special Cleaning and Care Insturctions
2. Front Lens Cleaning
3. Service and Maintenance
Being a solid-state fixture, and unlike most fixtures, the SL ParBlazer 100 UV requires very little routine
maintenance by the user. This section covers portions of the luminaire that can be removed for cleaning.
The SL ParBlazer 100 UV special care when it comes to cleaning from lens assembly. Additional care needs to
be taken with the plastic components because they are much easier to scratch or damage than glass.
Note: *Reagent grade isopropyl alcohol is good to use on the SL ParBlazer 100 UV plastic optics with
anti-reflection coatings.
If you have any questions regarding the use or care of your SL ParBlazer 100 UV, please contact Showline technical
support or your local Authorized Dealer.
WARNING! Under no circumstances should ammonia-based cleaners, acetone, or other harsh solvents be used
on or near the SL ParBlazer 100 UV. These types of cleaners or solvents can permanently damage the optics or
housings of the fixture.
Step 1.
Step 2.
Step 3.
Step 4.
Turn Off luminaire and allow to cool completely.
Apply a small amount of reagent grade isopropyl alcohol to lint-free lens tissue.
Wipe all debris, dirt, fingerprints, etc. from lens.
Using a second lint-free lens tissue, wipe off any alcohol residue.
WARNING! Disassembly ( other than as described herein), alterations, unauthorized service, etc. will void the
product warranty. Contact your local Showline office or an Authorized Service Center for technical support and
service.
CLEANING AND CARE
CLEANING AND CARE
18
Installation & User’s Manual SL ParBlazer 100 UV