Philips HD9225/50 User manual

ServiceManual
Philips Consumer Lifestyle
Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
Air Fryer
HD9225/50
HD9225/51
HD9225/52
HD9225/53
HD9220/50
11/10
PRODUCT INFORMATION
Safety info
-This product meets the requirements regarding
interference suppression on radio and TV.
-After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
-SAP coding : HD9225/50
HD9225/51
HD9225/52
HD9225/53
HD9220/50
OPTIONAL (accessories)
-Baking dish 4222 459 52761
TECHNICAL INFORMATION
-Voltage : 220 - 240V
-Frequency : 50 - 60 Hz
-Power consumption : 1425 W
-Product dimensions (W x H x D) : 287 x 315 x 384 mm
-Cord length : 1 meter
-Materials : Outer skin : Plastic (PP)
: Pan : Aluminized steel
: Basket : Aluminized steel
: Basket mesh : Stainless steel
: Coating : PTFE coating
-Capacity : 2.2 liter
(till max indicator)
-Weight : 7.0 kg
-Coloursetting : Star white /
Cashmere grey
-Temperature : 80 till 200 °C
-Fuse cut-off temp. Motor : 145 °C
TCO : 190 °C
IMPORTANT:
When you replace the pan (basketholder) or basket, rst check production week on the bottom of the appliance
to nd out which part(s) you need to order:
HD9225/5x
HD9220/5x
Pan Basket
1111 4222 459 54161 and 4222 459 54151 Due to compatibility issues, make sure you order both components
1111 1136 4222 459 54161 or 4222 459 52711 Components are compatible no need to be ordered both at once
1136 4222 459 54161 or 4222 459 54151 Components are compatible no need to be ordered both at once

HD9225/50 /51 /52 /53/ HD9220/50
2-9
TROUBLE SHOOTING
Part/
System Test Possible deviation Analyses
Replace
(depending of
the analyses
outcome)
Timer Check if the green light is lit,
and if you can hear the timer
ticking
The green light is not lit
but the timer is ticking
Check the timer-switch and the
fuse with a multimeter
Timer/Fuse
The green light is lit but
the timer is not ticking
Timer is defective Timer
Thermostat Set the temperature at 80°C
and check if the heating
element is getting warm
(Check input power approx.
1425W)
The green light should be lit
and the orange light should
switch off after it reaches
80°C
Both green and orange
light are lit but there is no
heating
Check the heating element with
a multimeter
Heating element
If the green light is lit and
the orange light is off
Check the thermostat with a
multimeter
Thermostat
If both the green and
orange light are off
Check the timer and fuse with a
multimeter
Timer/Fuse
The orange light does not
switch off after reaching
approx. 80°C
Thermostat is defective Thermostat
Motor fan
assy
Set the timer and listen if the
motor is running
Motor is not running The fan is scraping the housing
turning it by hand (Switch off the
power when you do this test!)
Motor fan assy
The fan is not scraping the
housing turning it by hand
(Switch off the power when you
do this test!):
Check the motor fan assy, timer
and fuse with a multi meter
Motor fan assy /
Timer/Fuse
Heating
element
Check if the heating element
is getting warm
(Check input power approx.
1425W)
If the Orange light is on
and the heating element
does not heat
Check the heating element with
a multimeter
Heating element
If the heating element
does not heat and the
orange light is off
Check the timer, fuse and
thermostat with a multimeter
Timer/Fuse/
Thermostat
Thermal fuse Set the timer and check if
the green light is lit
Green light is not lit Check the timer and fuse with a
multimeter
Timer/Fuse

HD9225/50 /51 /52 /53/ HD9220/50
3-9
REPAIR INSTRUCTIONS
General remark;
When you need to disconnect a wire from the crimp housing, please cut the wire half way (See in the picture below) and
always connect the wires with a new 2 wire crimp housing 4222 459 51851. To crimp the housing use the Lobster AK25 No2 or
Muromoto Tekko MR30A Nr 2 with Air pressure = 6 kg/cm².
Crimp instruction CE2
1) Strip wires: 16mm (0.63 in) Max. 13mm (0.51) Min.
2) Twist the wires together along the entire length of the strip and insert them into crimp housing .
3) Center the crimp tool on the sleeve.
4) Crimp the housing with 6 kg/cm².
Route the wire route, using 5 tie-wraps according the picture below;

HD9225/50 /51 /52 /53/ HD9220/50
4-9
A. Top cover removal
1. Open the cover from the top cover by using a athead
screw driver to open the 6 click connections.
2. Use a crosshead screw driver to unscrew the 4 screws A.
Note: When you close the top cover, use a screw
torque off 50 till 80 Nm (5 to 8 kgf.cm)
A
A
A
A
3. Use a athead screw driver to open the “timer top cover”
and pull the knob from the appliance.
4. Unscrew the screw Bunder the timer top cover.
B
Note: Replace the timer cover and / or the cover in
case of damage and / or scratches.
Tip: Open the “timer cover” from the bottom side,
to avoid scratches on visible places.
DISASSEMBLY- AND RE-ASSEMBLY ADVICE

HD9225/50 /51 /52 /53/ HD9220/50
5-9
B. Cover housing removal
1. Follow previous step A
2. Open the motor fan assy from the base by unscrewing the
6screws C. Be aware of the 2 screws under the lter.
C
C
CC
C
C
C. Heating element + Fan Removeval
1. Follow previous step Aand B
2. Undo the heating element from the double heat shield by
unscrewing the 3 screws D.
D
D
D
3. Cut the 2 heating element wires halfway and remove the
heating element.
4. Undo the nut from the left screw thread and remove the
fan.
D. Double heat shield removal
1. Follow previous step A, Band C
2. Remove the double heat shield out of the motor fan assy
by unscrewing the 3 screws E.
E
E
E
E. Timer removal
1. Follow step A
2. Unscrew the 2 screws Fbehind the timer knob.
F
F
3. Remove the wires of the timer.
DISASSEMBLY- AND RE-ASSEMBLY ADVICE

HD9225/50 /51 /52 /53/ HD9220/50
6-9
F. Thermostat removal
1. Follow previous step A
2. Remove the 3 screws Gfrom the thermostat assy.
G
G
G
3. Follow previous step B, C, D
By step Cdo not cut the wires.
Note: be careful with the wire/ heating element
connecting, this connection is fragile.
4. Remove the thermostat sensor by undoing the metal band.
metal band
Note: Please make sure while re-assembling the new
thermostat that the routing will be done as
shown in below picture.
DISASSEMBLY- AND RE-ASSEMBLY ADVICE
G. Motor assy removal
1. Follow previous step A, B, C, D
By step Cdo not cut the wires.
2. Remove the thermostat sensor (See instruction F4)
3. Remove the fuse and the earth connection from the
double heat shield.
Earth connection
Double
heat shield
Fuse
4. Cut the motor wires half way and remove the motor fan
assy.

HD9225/50 /51 /52 /53/ HD9220/50
7-9
PARTS LIST
Electrical circuit
When the appliance does not work, check the electrical circuit.
Open de lid panel always on the underside. Always replaces this panel in case of damaged, scratches body or broken click
connection.
LThermostat
N
E
Resistor
Orange
Neon lamp
Resistor
Green
Neon lamp
M
HeaterMotor
Therm.
Fuse
220 - 240 V
50 - 60 Hz
RD
BK
BL
WT
YL
GN
= Red
= Black
= Blue
= White
= Yellow
= Green
RD
YL & GN
YL & GN
BL
BK BK
BK
WT
BK
WT
BL
WT
BL
WT
BL
WT WT
Pos Service code Description
1
2
3
4
5
4222 459 52771
4222 459 52691
4222 459 52701
4222 459 51901
4222 459 52711
4222 459 54151
Cover
Timer knob
Timer cover
Food separator
Basket wk1136
wk1136
Cashmere grey
Black
Oyster Metellic
Cashmere grey
6
7
8
9
4222 459 52721
4222 459 51911
4222 459 54671
4222 459 52731
4222 459 53251
Pan (Basket holder)
Rubber foot wk1116
Rubber foot wk1116
Top cover
Stainless steel timer
Star white
Star white
10
11
12
13
4222 459 49181
4222 459 49141
4222 459 49131
4222 459 53391
4222 459 52741
Fuse incl. wires
Fan
Heating element incl. wires
Heating element incl. wires
Base incl. wires
220-240 V, 50 Hz
220-240 V, 60 Hz
Star white
14
15
16 *
4222 459 52751
4222 459 49201
4222 459 53401
4222 459 52761
Thermostat assy
Motor, fan assy
Motor, fan assy
Baking dish
220-240 V, 50 Hz
60 Hz
4222 459 51851 10 pieces of 2 wire crimp housing (CE-2)
* Optional for HD9220/50

HD9225/50 /51 /52 /53/ HD9220/50
8-9
EXPLODED VIEW
2
6
5
4
3
1
7
4x
16

HD9225/50 /51 /52 /53/ HD9220/50
9-9
EXPLODED VIEW
8
9
14
15
11
12
13
A
4x
C
6x
F
2x
B
D
3x
E
3x
G
3x
10