Philips 154948 User manual

◗Ordering Information
Ordering Code CDM150/U/PS/4K ALTO
ANSI Designation M102/M142/E
Product Number 154948
Description Ceramic Metal Halide
Pulse Start TCLP Compliant
Package Quantity 12
◗Physical Characteristics
Bulb Size ED-23.5
Bulb Finish Clear
Base Mogul
Max. Overall Length (MOL) 7.75" (195mm)
Light Center Length (LCL) 5.00" (127mm)
Arc Length .3125" (8mm)
Arc Tube Material Ceramic (PCA)
Maximum Permissible Bulb Temperature 400ºC ANSI
Maximum Permissible Base Temperature 190ºC ANSI
Maximum Bulb to Base Eccentricity 3º
Maximum Art Tube to Base Eccentricity 3º
◗Operating Characteristics (Photometric)
Approximate Initial Lumens113,000
Approximate Mean Lumen29750
Efficacy (LPW) 87
Approximate Lumen Maintenance
@ 10% Rated Life 90%
Approximate Lumen Maintenance
@ 40% Rated Life 75%
Rated Average Life, Hours324,000
Correlated Color Temperature (CCT) 4000 K Vertical
3700 K Horizontal
CIE Chromaticity Approximate x-.385, y-.375
Color Rendering Index (CRI) 90
◗Operating Position
Universal—For enclosed fixtures only
◗TCLP Characteristics
Toxicity Characteristic Leaching Procedure (Federal TCLP) Results
Hg Hg Pb
(mg/l) (mg/lamp) (mg/l)
Federal Limit Max (Mercury & Lead) 0.200 n/a 5.00
CDM150/U//PS/4K ALTO (Average) 0.0923 11.4 0.00
MasterColor®CDM Ceramic Metal Halide
150 Watt Pulse Start for Enclosed Fixtures
featuring ALTO®Lamp Technology
MOL
LCL
ARC
Length
0
50
40
30
20
10
60
70
80
90
100
4000 8000 12,000 16,000 20,000 24,0000
Percent LumenMaintenance
Life (Hours)
Approximate LumenMaintenance Curve
0
50
40
30
20
10
60
70
80
90
100
10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000
Percent Survival
Life (Hours)
Approximate Survival Curve

MasterColor®CDM Ceramic Metal Halide 150 Watt Pulse Start for Enclosed Fixtures
featuring ALTO®Lamp Technology
Electrical Data (Subject to change without notice)
Lamp Watts (Nominal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Lamp Operating Voltage (rms) (Nominal). . . . . . . . . . . . . . . . . . 95V
Initial Lamp Voltage Range (rms). . . . . . . . . . . . . . . . . . . . . . . . . . 85–105V
Lamp Operating Current (Amps) (rms) (Nominal). . . . . . . . . . 1.8
Maximum Lamp Starting Current (Amps)(rms) . . . . . . . . . . . . . 3.0
Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . . . . . . . . 1.8
Warm-up Time to 95% Minimum Lamp Operating Voltage . . . 2 Minutes
Re-strike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Minutes
Ballast Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI M142/M102/E
IgnitionPulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000V min.; 4000V max
Pulse Width @ 2700 Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9µ (micro sec.)
Pulse RepetitionRate (Minimum). . . . . . . . . . . . . . . . . . . . . . . . . 1 pulse per half cycle
Starting Ballast OpenCircuit Voltage (Minimum):
@10°C for 10 seconds – 98% of “0” hr lamps start . . . . . . 235 Vrms
@-30°C for 120 seconds – 90% of 100 hr lamps start . . . 235 Vrms
Minimum Operating Temperature. . . . . . . . . . . . . . . . . . . . . . . . . -30°C
Reference Ballast Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Ω(ohms)
Maximum Lamp Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Watts
Rated Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 volts
Maximum Voltage Increase by Fixture . . . . . . . . . . . . . . . . . . . . . 5V rms
1) Measured at 100 hours of life invertical and horizontal positions.
2) Approximate meanlumenoutput at 40% of lamp rated average life. Measured invertical and horizontal operating positions.
3) Rated average life is the life obtained, onthe average, from large representative groups of lamps inlaboratory tests under controlled conditions at 10 or more operating hours per start. It is based onsurvival of at least
50% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.
Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
A Division of Philips Electronics North America Corporation
Updated 10/06 TDS-154948
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics Ltd.
www.philips.com
Notes: Pulse Start Metal Halide lamps are designed for operation on only approved ballasts with metal halide pulse ignitors.
WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS
R“WARNING:
These lamps cancause serious skinburnand eye inflammationfrom
short wave ultraviolet radiationif outer envelope of the lamp is brokenor punctured.
Do not use where people will remainfor more thana few minutes unless adequate shielding
or other safety precautions are used. Certainlamps that will automatically extinguish when
the outer envelope is brokenor punctured are commercially available.”This lamp complies
with FDA radiationperformance standard 21 CFR subchapter J. (USA:21CFR 1040.30
Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off at once and replace the lamp
to avoid possible injury from hazardous short wave ultraviolet radiation. Do
not scratch the outer bulb or subject it to pressure as this could cause the
outer bulb to crack or shatter.A partial vacuum in the outer bulb could cause
glass to fly if the envelope is struck.
WARNING: The arc-tube of metal halide lamps are designed to operate under high
pressure and at temperatures up to 1000° C and canunexpectedly rupture due to internal
or external factors such as a ballast failure or misapplication. If the arc-tube ruptures for any
reason, the outer bulb may break and pieces of extremely hot glass might be discharged into
the surrounding environment. If such a rupture were to happen, THERE IS A RISK OF
PERSONAL INJURY, PROPERTY DAMAGE, BURNS AND FIRE.
This lamp contains an arc tube with a filling gas containing not less than 25nCi
of Kr-85 and is distributed by Philips Lighting Company, a division of Philips
Electronics North America Corporation, Somerset, New Jersey, 08875
RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.
Allowing lamps to operate until they fail is not advised and may increase the
possibility of inner arc tube rupture.
CAUTION:TO REDUCE THE RISK OF PERSONAL INJURY, PROPERTY
DAMAGE, BURNS AND FIRE RESULTING FROM AN ARC TUBE RUPTURE,
THE FOLLOWING LAMP OPERATING INSTRUCTIONS MUST BE
FOLLOWED.
LAMP OPERATING INSTRUCTIONS:
1. RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE. Allowing lamps to operate
until they fail is not advised and may increase the possibility of inner arc tube rupture.
2. Before lamp installation/replacement, shut power off and allow lamp and fixture to cool
to avoid electrical shock and potential burnhazards.
3. Use only inanenclosed fixture capable of withstanding particles of glass having
temperatures up to 1000°C, unless otherwise noted.
4. Use only auxiliary equipment meeting Philips and/or ANSI standards.
Use withinvoltage limits recommended by ballast manufacturer.
A. Operate lamp only withinspecified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
C. All Pulse Start lamps require a socket rated to withstand a 4000 Volt pulse.
5. Periodically inspect the outer envelope. Replace any lamps that show scratches,
cracks or damage.
6. If a lamp bulb support is used, be sure to insulate the support electrically to avoid
possible decompositionof the bulb glass.
7. Protect lamp base, socket and wiring against moisture, corrosive atmospheres and
excessive heat.
8. Time should be allowed for lamps to stabilize incolor whenturned onfor the first time.
This may require several hours of operation, with more thanone start. Lamp color is also
subject to change under conditions of excess vibrationor shock, and color appearance
may vary betweenindividual lamps.
9. Lamps may require 10 to 15 minutes to re-light if there is a power interruption.
10. Take care inhandling and disposing of lamps. If anarc tube is broken, avoid skincontact
with any of the contents or fragments.
11. Use this lamp only ina fixture that contains a Pulse Start metal halide ballast and
is specifically designed for use with Pulse Start metal halide lamps.