Philips CompactCare GC6500 Series User manual

Always here to help you
User manual
Register your product and get support at
www.philips.com/welcome
GC6500
GC6400
series
Downloaded from www.vandenborre.be

Downloaded from www.vandenborre.be

1
Downloaded from www.vandenborre.be

Downloaded from www.vandenborre.be

GC6500,GC6400 SERIES
ENGLISH 6
DANSK 14
DEUTSCH 22
 31
ESPAÑOL 40
SUOMI 49
FRANÇAIS 57
ITALIANO 66
NEDERLANDS 75
NORSK 83
PORTUGUÊS 91
SVENSKA 100
TÜRKÇE 108
Downloaded from www.vandenborre.be

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.com/welcome.
General description (Fig. 1)
A Supply hose
B Temperature dial
C Temperature light
D Steam lock
E Steam boost button (GC6540/GC6490/GC6480/GC6470)
F Steam trigger
G Steam tank cap
H Iron stand
I Steam tank
J Soleplate
K Mains cord
L On/off switch with power-on light
M ’Steam ready’ light (GC6540 only)
N ’Steam tank empty’ light (GC6540 only)
O Iron lock slide (GC6540/GC6530 only)
P Steam control (GC6540 only)
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
- Never immerse the iron or the steam tank in water.
Warning
- Check if the voltage indicated on the type plate corresponds to the
local mains voltage before you connect the appliance.
- Do not use the appliance if the plug, the mains cord, the supply hose or
the appliance itself shows visible damage, or if the appliance has been
dropped or leaks.
- If the mains cord or the supply hose is damaged, you must have it
replaced by Philips, a service centre authorised by Philips or similarly
qualied persons in order to avoid a hazard.
- Never leave the appliance unattended when it is connected to the mains.
- This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance.
ENGLISH
Downloaded from www.vandenborre.be

- Do not let the mains cord and supply hose come into contact with the
hot soleplate of the iron.
- If steam escapes from under the steam tank cap when the appliance
heats up, switch off the appliance and tighten the steam tank cap. If
steam continues to escape when the appliance heats up, switch off the
appliance and contact a service centre authorised by Philips.
- Do not remove the steam tank cap from the steam tank when the
steam tank is still under pressure, as this could cause scalding by hot
water or steam.
- Do not use any other cap on the steam tank than the cap that has been
supplied with the appliance, as the steam tank cap also functions as a
safety valve.
Caution
- Only connect the appliance to an earthed wall socket.
- Check the mains cord and the supply hose regularly for possible damage.
- Always place and use the iron and the steam tank on a stable, level and
horizontal surface.
- The iron stand and the soleplate of the iron can become extremely hot
and may cause burns if touched. If you want to move the steam tank, do
not touch the stand.
- When you have nished ironing, when you clean the appliance, when
you ll or empty the steam tank and also when you leave the iron even
for a short while: put the iron on the iron stand, set the on/off switch to
‘O’ and remove the mains plug from the wall socket.
- Rinse the steam tank regularly according to the instructions in chapter
‘Cleaning and maintenance’.
- This appliance is intended for household use only.

This Philips appliance complies with all standards regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.

1 Remove any sticker or protective foil from the soleplate and clean the soleplate with a soft cloth.
2 Fully unwind the mains cord and supply hose.
3 Place the steam tank on a stable, level surface.
4 Place the iron on the iron stand.
ENGLISH 7
Downloaded from www.vandenborre.be

Preparing for use
Filling the steam tank
Never immerse the steam tank in water.
Do not open the steam tank cap when the iron and the steam tank are still hot.
1 Remove the mains plug from the wall socket.
2 Slowly unscrew the steam tank cap (Fig. 2).
You may hear a sound when you remove the cap.This sound is caused by the vacuum or residual
pressure inside the steam tank and is perfectly normal.
3 Pour water into the steam tank (max. 800ml) (Fig. 3).
Your appliance has been designed to be used with tap water. If you live in an area with very hard
water, fast scale build-up will occur. Therefore it is recommended to ll the water tank with 50%
distilled water and 50% tap water to prolong the lifetime of your appliance.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the steam
tank, as your appliance is not designed to work with these chemicals.Also, do not put hot water
in the steam tank.
4 Screwthesteamtankcaptightlyontothellingopeningofthesteamtank.

If the steam tank becomes empty during ironing, follow the procedure below to quickly rell the
steam tank.
1 Keep the appliance plugged into the mains and make sure the on/off switch is set to ‘I’ (Fig. 4).
2 Press the steam trigger until you no longer hear any steam escaping from the
appliance (Fig. 5).
3 To depressurise the steam tank, keep the steam trigger pressed in and slowly unscrew the
steam tank cap anticlockwise.
Place a piece of cloth over the cap when you unscrew it. Make sure there is no steam left in the
steam tank.
4 Remove the mains plug from the wall socket and wait approximately 15 minutes for the
appliance to cool down.
5 Fill the steam tank as described in section ‘Filling the steam tank’ and let the appliance heat
up again.
Setting the temperature
Always place the steam tank on a stable, level and horizontal surface. Do not put the steam tank
on the soft part of the ironing board.
1 Put the iron on the iron stand.
Do not put the hot iron on the supply hose or the mains cord. Make sure the cord does not
come into contact with the hot soleplate.
2 To set the required ironing temperature, turn the temperature dial to the appropriate
position (Fig. 6).
Check the laundry care label for the required ironing temperature:
ENGLISH8
Downloaded from www.vandenborre.be

Laundry care table
Symbol on laundry
care label Type of fabric Temperature setting Steam setting (GC6540 only)
BSynthetic fabrics (e.g. acetate, acrylic,
viscose, polyamide, polyester) and
silk
1-
CWool 2ECO
DCotton, linen 3to Max ECO to ;
ZPlease note that Zon the label
means that the article cannot be
ironed.
- -
If you do not know what kind or kinds of fabric an article is made of, determine the right ironing
temperature by ironing a part that is not visible when you wear or use the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric to prevent shiny patches.
Start ironing the articles that require the lowest ironing temperature, such as those made of
synthetic bres.
3 Put the mains plug in an earthed wall socket and set the on/off switch to ‘I’.
,The steam tank and the soleplate heat up.
,When the temperature light goes out, the iron has reached the set temperature.As soon as
the water in the steam tank is ready for steam ironing:
- GC6540: the ‘steam ready’ light goes on.
- GC6530/GC6520/GC6516/GC6515/GC6511/GC6510/GC6505/GC6490/GC6480/GC6470:
the power-on light in the on/off switch goes out.
Note: During steam ironing, the temperature light goes on from time to time.This indicates that the iron
is heating up to the set temperature.
Note: If you have been ironing at a high temperature and then set the temperature dial to a lower
setting, wait until the temperature light goes on and goes out again before you continue ironing.This
prevents damage to your fabrics.
Tips
- If the fabric consists of various kinds of bres, always select the temperature required by the
most delicate bre, i.e. the lowest temperature. For example: if an article consists of 60%
polyester and 40% cotton, it should be ironed at the temperature indicated for polyester ( 1)
and without steam.
- When you steam iron woollen fabrics, shiny patches may occur.To prevent this, use a dry
pressing cloth or turn the article inside out and iron the reverse side.
- Iron velvet and other fabrics that tend to acquire shiny patches in one direction only (along with
the nap) while you apply very little pressure.
- Do not use steam when you iron coloured silk.This could cause stains.
Using the appliance
Steam ironing
1 Make sure that there is enough water in the steam tank.
2 Set the required ironing temperature (see chapter ‘Preparing for use’).
Note: Steam ironing is only possible at higher ironing temperatures (temperature settings 2to MAX).
ENGLISH 9
Downloaded from www.vandenborre.be

3 Put the mains plug in an earthed wall socket and set the on/off switch to ‘I’.
- The power-on light in the on/off switch and the temperature light on the iron go on to indicate
that the steam tank and the iron start to heat up.
4 GC6540: Select a steam setting suitable for the selected ironing temperature: (Fig. 7)
- Select steam setting ECO for temperature setting 2.
- Select a steam setting between ECO and ;for temperature settings 3to MAX.
5 The steam tank and the soleplate heat up.
- Cold start: the soleplate takes approximately 2 minutes to heat up and the steam tank takes
approximately 6 minutes to heat up.
- Quick reheat: if you rell the steam tank during the ironing process, the water in the steam
tank takes approximately 6 minutes to heat up.
,When the iron has reached the set temperature, the temperature light goes out.
,As soon as the water in the steam tank is ready for steam ironing:
- GC6540: the ‘steam ready’ light goes on (Fig. 8).
Note: During steam ironing, the ‘steam ready’ light goes out from time to time.This indicates that the
steam tank is heating up to the right temperature.
- GC6530/GC6520/GC6516/GC6515/GC6511/GC6510/GC6505/GC6490/GC6480/GC6470:
the power-on light in the on/off switch goes out.
6 Press the steam trigger and keep it pressed while you steam iron (Fig. 5).
Tip:When you put down the iron during ironing, put it on its heel.
Note: If you have not used the steam function for some time, the steam that was still present in the
supply hose has condensed into water.When you start steam ironing again, this may cause some
spluttering in the appliance and a few droplets of water may escape from the soleplate.
Note:To prevent droplets from falling onto your garments, hold the iron over an old cloth and press the
steam trigger until the steam production has normalised before you start steam ironing again.
Steam lock function
The steam lock allows you to steam iron non-stop without having to press the steam trigger
continuously.
1 To steam iron non-stop, slide the steam lock to position ‘ON’ (Fig. 9).
- To stop steam ironing, slide the steam lock to position ‘OFF’, the iron now only produces steam
when you press the steam trigger.
Ironing without steam
1 Set the required ironing temperature (see chapter ‘Preparing for use’).
2 Iron without pressing the steam trigger.
,Some steam escapes if you press the steam trigger by accident while you iron.
,If the steam tank is empty or has not heated up yet, you hear a clicking sound inside the
steam tank.This happens when the steam valve opens and is perfectly harmless.
Features
Vertical steam ironing
You can also steam iron when you hold the iron in vertical position.This is useful for removing
creases from hanging clothes (e.g. jackets, suits and coats), curtains etc.
1 Hold the iron in vertical position and press the steam trigger (Fig. 10).
Never direct the steam at people.
ENGLISH10
Downloaded from www.vandenborre.be

Steam boost (GC6540/GC6470 only)
During steam ironing, you can use the steam boost function to remove stubborn creases.
1 Set the temperature dial to a setting between 3and MAX.
2 Press the steam boost button. (Fig. 11)
Note: Use the steam boost function intermittently. If water droplets come out of the soleplate, let the iron
heat up for at least one minute before you use the steam boost function again.
Never direct the steam at people.
Variable steam (GC6540 only)
The steam control is continuously adjustable and can be set to any position between ECO and ;
(see chapter ‘Preparing for use’).
‘Steam tank empty’ light (GC6540 only)
When the water in the steam tank runs out during use, the ‘steam tank empty’ light goes on.
1 Rellthesteamtankwithwater(seechapter‘Preparingforuse’,section‘Fastrell’).
’Steam ready’ light (GC6540 only)
When the steam tank is ready for steam ironing, the ‘steam ready’ light goes on.
Cleaning and maintenance
After ironing
1 Set the on/off switch to ‘O’ (Fig. 4).
2 Remove the mains plug from the wall socket.
3 Put the iron on the iron stand, set the steam control to ECO (GC6540 only) and let the
appliance cool down.
Iron
1 Clean the iron with a damp cloth.
2 Wipe scale and any other deposits off the soleplate with a damp cloth and a non-abrasive
(liquid) cleaner.
Never immerse the iron in water nor rinse it under the tap.
Steam tank
Rinse the steam tank once a month or after you have used the appliance approximately 10 times.
1 Carefully remove the steam tank cap (Fig. 2).
Lettheappliancecooldownsufcientlybeforeyouremovethesteamtankcap.
2 Rinse the steam tank with 500ml of fresh water.
3 Hold the steam tank upside down over the sink and pour out the water (Fig. 12).
4 Screw the steam tank cap back onto the steam tank.
ENGLISH 11
Downloaded from www.vandenborre.be

Storage
1 Remove the mains plug from the wall socket and let the appliance cool down.
Makesuretheappliancehascooleddownsufcientlybeforeyouputitaway.
2 Empty the steam tank.
3 Regularly check if the mains cord and the supply hose are still undamaged and safe.
4 GC6540/GC6530 only: For safe storage, lock the iron onto the stand with the iron lock slide.
First put down the tip (1) and then put down the heel (2) (Fig. 13).
5 Wind up the hose and cord separately.
6 Insert the hose and cord neatly in the cord storage compartment (Fig. 14).
Environment
- Do not throw away the appliance with the normal household waste at the end of its life, but
hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the
environment (Fig. 15).
Guarantee and service
If you need service or information or if you have a problem, please visit the Philips website at
www.philips.com/service or contact the Philips Consumer Care Centre in your country. You nd
its phone number in the worldwide guarantee leaet. If there is no Consumer Care Centre in your
country, go to your local Philips dealer.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If
you are unable to solve the problem with the information below, visit www.philips.com/support
for a list of frequently asked question or contact the Consumer Care Centre in your country.
Problem Cause Solution
Some smoke
comes out of the
appliance after it
has been
switched on for
the rst time.
This is normal. Some parts of the
appliance have been greased lightly in
the factory.
This phenomenon ceases after a
short while.
Dirt particles
come out of the
soleplate of the
new iron.
This is normal with a new iron. These particles are harmless
and stop coming out of the
soleplate after you have used the
iron a few times.
Droplets of
water escape
from the
soleplate.
The temperature dial has been set to
a temperature that is too low for
steam ironing.
Set an ironing temperature that is
suitable for steam ironing
(temperature settings 2to MAX).
The appliance is not switched on. Set the on/off switch to ‘I’.
The steam tank has been placed on an
unstable and/or uneven surface. Put the steam tank on a stable and even surface.
ENGLISH12
Downloaded from www.vandenborre.be

Problem Cause Solution
When you start steam ironing, the
hose is cold. Steam condenses in the
hose, causing droplets of water to
escape from the soleplate.
This is normal. Hold the iron over an
old cloth and press the steam trigger.
The cloth absorbs the drops.After a
few seconds, the steam production
becomes normal.
The appliance
does not
produce any
steam.
The appliance is not switched on. Set the on/off switch to ‘I’
The steam tank is not hot enough to
produce steam. Wait 6 minutes for the steam tank to heat up.
You are not pressing the steam trigger. Press the steam trigger and keep it
pressed while you steam iron.
There is not enough water in the
steam tank. Fill the steam tank. See chapter ‘Preparing for use - Filling the Steam
tank’.
No steam comes
out of the
soleplate.
Superheated (i.e. high-quality) steam is
hardly visible, especially when the
temperature dial is set to maximum
position and even less so when the
ambient temperature is relatively high.
To check if the iron really produces
steam, hold a (cold) mirror in front
of the soleplate vents.
The soleplate is
dirty. Impurities or chemicals present in the water have deposited on the soleplate. Clean the soleplate with a damp cloth.
You have been ironing at too high
temperatures. Clean the soleplate with a damp cloth. Set the iron to the required
ironing temperature (see chapter
‘Preparing for use’, section ‘Setting
the temperature’).
Steam escapes
from the lling
hole area during
ironing.
You may not have tightened the steam
tank cap properly or you have spilled
some water around the lling hole
Switch off the appliance and let it
cool down. Remove the steam tank
cap, wipe away the water round the
lling hole and tighten the steam
tank cap again.Then switch on the
appliance again.
Wet spots
appear on the
garment during
ironing
The wet spots that appear on your
garment after you have steam ironed
for some time may be caused by
steam that has condensed onto the
ironing board. Iron the wet spots
without steam for some time to dry
them. If the underside of the ironing
board is wet, wipe it dry with a piece
of dry cloth.
To prevent steam from condensing
onto the ironing board, use an
ironing board with a wire mesh top.
ENGLISH 13
Downloaded from www.vandenborre.be

14
Introduktion
Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte af den support, Philips tilbyder,
skal du registrere dit produkt på www.philips.com/welcome.

A Dampslange
B Temperaturvælger
C Temperaturindikator med lys
D Damplås
E Dampskudsknap (GC6540/GC6490/GC6480/GC6470)
F Dampudløser
G Låg til damptank
H Holder til strygejernet
I Damptank
J Strygesål
K Netledning
L On/off-kontakt med lys
M Lysindikator for “damp klar” (kun GC6540)
N Lysindikator for tom damptank (kun GC6540)
O Strygejernslås (kun GC6540/GC6530)
P Dampkontrol (kun GC6540)
Vigtigt
Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i
brug, og gem den til eventuelt senere brug.
Fare
- Hverken strygejern eller damptank må kommes ned i vand.
Advarsel
- Kontrollér, om spændingsangivelsen på typeskiltet svarer til den lokale
netspænding, før du tilslutter apparatet.
- Brug ikke apparatet, hvis stik, netledning, dampslange eller selve apparatet
viser tegn på beskadigelse, eller hvis apparatet er blevet tabt, eller det er utæt.
- Hvis ledningen eller dampslangen beskadiges, må de kun udskiftes af
Philips, et autoriseret Philips-serviceværksted eller af en kvaliceret
fagmand for at undgå enhver risiko ved efterfølgende brug.
- Hold altid apparatet under opsyn, når det er tilsluttet strøm.
- Dette apparat er ikke beregnet til at blive brugt af personer (herunder
børn) med nedsatte fysiske og mentale evner, nedsat følesans eller
manglende erfaring og viden, medmindre de er blevet vejledt eller instrueret
i apparatets anvendelse af en person, der er ansvarlig for deres sikkerhed.
- Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke
kan komme til at lege med det.
- Lad ikke netledningen og dampslangen komme i kontakt med den
varme strygesål på strygejernet.
DANSK
Downloaded from www.vandenborre.be

- Hvis der kommer damp ud under låget til damptanken, mens apparatet
varmer op, skal du slukke for apparatet og stramme låget til damptanken
til. Kommer der fortsat damp ud, mens apparatet varmer op, skal du
slukke for apparatet og kontakte et autoriseret Philips-serviceværksted.
- Tag aldrig låget af damptanken, mens damptanken er under tryk, da det
kan forårsage skoldning med varmt vand eller damp.
- Brug kun det medfølgende låg til damptanken, da det samtidig fungerer
som sikkerhedsventil.
Forsigtig
- Apparatet må kun sluttes til en stikkontakt med jordforbindelse.
- Kontrollér med jævne mellemrum, at netledningen og dampslangen er
hele og ubeskadigede.
- Placér og brug altid strygejern og damptank på et stabilt, plant og
vandret underlag.
- Strygejernets holder og strygesål kan blive meget varme og forårsage
brandsår ved berøring. Undgå at røre holderen, hvis damptanken yttes.
- Når du er færdig med at stryge, når du rengør apparatet, når du fylder
eller tømmer tanken, og når du forlader strygejernet – selv om det kun
er i et kort øjeblik – skal du placere strygejernet i standeren, sætte
kontakten på “O” og tage stikket ud af stikkontakten.
- Rengør damptanken regelmæssigt ifølge anvisningerne i afsnittet
“Rengøring og vedligeholdelse”.
- Dette apparat er kun beregnet til almindelig husholdningsbrug.
Elektromagnetiske felter (EMF)
Dette Philips-apparat overholder alle standarder for elektromagnetiske felter (EMF).Ved korrekt
anvendelse i overensstemmelse med instruktionerne i denne brugervejledning er apparatet sikkert
at anvende ifølge den videnskabelige viden, der er tilgængelig i dag.
Før apparatet tages i brug
1 Fjerneventuellemærkaterellerbeskyttelseslmfrastrygesålen,ogrengørdenmedenblødklud.
2 Rul netledningen og dampslangen helt ud.
3 Anbringdamptankenpåetstabiltogplantunderlag.
4 Sæt strygejernet i standeren.
Klargøring
Fyldning af damptanken
Damptankenmåaldrigkommesnedivand.
Tagikkelågetafdamptanken,sålængestrygejernogdamptankervarme.
1 Tag stikket ud af stikkontakten.
2 Skrulågettildamptankenforsigtigtaf(g.2).
DANSK 15
Downloaded from www.vandenborre.be

Derkanforekommeenlyd,nårdufjernerlåget.Lydenskyldesdetvakuumellerresttryk,dereri
damptanken, og er helt normal.
3 Hældvandidamptanken(maks.800ml)(g.3).
Apparatet er udviklet til brug med vand fra hanen. Hvis du bor i et område med meget hårdt vand,
vil der hurtigt opstå kalkaejringer. Det anbefales derfor, at man fylder vandtanken med vand 50 %
destilleret vand og 50 % postevand for at forlænge apparatets levetid.
Kom aldrig parfume, eddike, stivelse, afkalkningsmiddel, strygemidler eller andre kemikalier i
damptanken,daditapparaterikkedesignettilatfungeresammenmeddissekemikalier.Dumå
heller ikke hælde varmt vand i damptanken.
4 Skrulågetgodtfastpådamptankenspåfyldningsåbning.
Hurtig påfyldning
Hvis damptanken bliver tom under strygningen, skal du følge denne fremgangsmåde for hurtigt at
fylde den igen.
1 Ladapparatetværetilsluttetlysnettet,ogsørgforaton/off-kontaktenstårpå“I”(g.4).
2 Trykpådampudløseren,indtilduikkelængerekanhøre,atderslipperdampudfra
apparatet(g.5).
3 Trykkettagesafdamptankenvedatholdedampudløserennedeoglangsomtdrejelågettil
damptanken mod uret.
Læg en klud hen over låget, når du skruer det af. Kontroller, at der ikke er mere damp i tanken.
4 Tagstikketudafstikkontakten,ogventca.15minutter,mensapparatetkøleraf.
5 Fylddamptankensombeskrevetiafsnittet“Påfyldningafdamptanken”,ogladapparatet
varme op igen.
Temperaturindstilling
Placéraltiddamptankenpåetstabilt,plantogvandretunderlag.Damptankenmåikkestillespå
selve strygebrættet.
1 Stil strygejernet i holderen.
Stilikkedetvarmestrygejernovenpådampslangenellernetledningen.Sørgfor,atnetledningen
ikkekommerikontaktmeddenvarmestrygesål.
2 Indstildenønskedestrygetemperaturvedatdrejetemperaturvælgeren(g.6).
Kontrollér tøjets vaskemærke, og nd den rette strygetemperatur.
Tabel over vaskemærker
Symbolpå
tøjets
vaskemærke
Stoftype Temperaturindstilling Dampindstilling
(kun GC6540)
BKunststoffer (f.eks. acetat, acryl,
viskose, polyamid, polyester) og silke
1-
CUld 2ECO
DBomuld, hør, linned 3til Max ECO til ;
DANSK16
Downloaded from www.vandenborre.be

Symbolpå
tøjets
vaskemærke
Stoftype Temperaturindstilling Dampindstilling
(kun GC6540)
ZBemærk, at Zsymbolet på
vaskemærket betyder, at det
pågældende stykke tøj ikke tåler
strygning.
- -
Er du i tvivl om, hvilket materiale et stykke tøj er fremstillet af, må du nde den rette
strygetemperatur ved at stryge et sted, som ikke er synligt, når du har tøjet på.
Silke, uld eller kunststof: Stryg tøjet på vrangen for at undgå blanke skjolder.
Begynd med at stryge det tøj, som kræver den laveste temperatur, dvs. det, som er fremstillet af kunststof.
3 Sætstikketienjordetstikkontaktogsæton/off-kontaktenpå“I”.
,Damptankenogstrygesålenvarmerop.
,Nårtemperaturindikatorenslukker,harstrygejernetnåetdenindstilledetemperatur.Når
vandet i damptanken er varmt nok til dampstrygning:
- GC6540: Lysindikatoren for “damp klar” tænder.
- GC6530/GC6520/GC6516/GC6515/GC6511/GC6510/GC6505/GC6490/GC6480/GC6470:
Lyset i on/off-kontakten slukker.
Bemærk: Under dampstrygning tænder og slukker temperaturindikatoren fra tid til anden. Dette indikerer
blot, at strygejernet opvarmes til den indstillede temperatur.
Bemærk: Hvis du har strøget ved høj temperatur og derefter indstiller temperaturvælgeren til en lavere
temperatur, skal du vente, indtil temperaturindikatoren tænder og slukker igen, før du fortsætter med at
stryge. Så undgår du at beskadige stoffet.
Gode råd
- Hvis stoffet er fremstillet af ere slags bre, skal du altid vælge den temperatur, som passer til den
sarteste bertype, dvs. den laveste temperatur. Hvis et stykke tøj f.eks. består af 60 % polyester og
40 % bomuld, bør det stryges ved den temperatur, som passer til polyester ( 1), og uden damp.
- Når du stryger uldstoffer, kan der opstå blanke skjolder. For at undgå dette skal du bruge en tør
klud til at lægge imellem eller vende vrangen ud på tøjet og stryge det på bagsiden.
- Fløjl og andre stoffer, som har tendens til at få blanke skjolder, bør kun stryges i én retning (med
luven) og kun med et let tryk.
- Undlad at bruge damp ved strygning af indfarvede silkestoffer, da det kan give skjolder på tøjet.
Sådan bruges apparatet
Dampstrygning
1 Sørgfor,atderernokvandidamptanken.
2 Indstildenønskedestrygetemperatur(seafsnittet“Klargøring”).
Bemærk: Dampstrygning er kun mulig ved høje strygetemperaturer (temperaturindstillingerne 2til MAX).
3 Sætstikketienjordetstikkontaktogsæton/off-kontaktenpå“I”.
- Lyset i on/off-kontakten og temperaturindikatoren på strygejernet viser nu, at damptanken og
strygejernet varmer op.
4 GC6540:Vælgdendampindstilling,sompassertildenvalgtestrygetemperatur:(g.7)
- Vælg dampindstillingen ECO til temperaturindstillingen 2.
- Vælg en dampindstilling mellem ECO og ;for temperaturindstillinger fra 3til MAX.
DANSK 17
Downloaded from www.vandenborre.be

5 Damptankenogstrygesålenvarmerop.
- Koldstart: Det tager ca. 2 minutter at varme strygesålen op, og ca. 6 minutter at opvarme
damptanken.
- Hurtig genopvarmning: Hvis du fylder vand på damptanken i løbet af en strygeproces, tager
genopvarmningen ca. 6 minutter.
,Nårstrygejernetharnåetdenindstilledetemperatur,slukkertemperaturindikatoren.
,Såsnartvandetivandtankenervarmtnoktildampstrygning:
- GC6540: Lysindikatoren for “damp klar” tænder (g. 8).
Bemærk: Under dampstrygning slukker lysindikatoren for “damp klar” indimellem. Dette indikerer, at
damptanken opvarmes til den valgte temperatur.
- GC6530/GC6520/GC6516/GC6515/GC6511/GC6510/GC6505/GC6490/GC6480/GC6470:
Lyset i on/off-kontakten slukker.
6 Trykpådampudløseren,ogholddennede,mensdudampstryger(g.5).
Tip: Når du stiller strygejernet fra dig under strygningen, skal det stå på højkant.
Bemærk: Har du ikke brugt dampfunktionen i et stykke tid, vil den resterende damp i dampslangen være
fortættet til vand. Når du begynder at dampstryge igen, kan det få strygejernet til at sprutte, og der kan
dryppe et par vanddråber ud igennem strygesålen.
Bemærk: For at undgå at der drypper vand på tøjet, holdes strygejernet over en gammel klud og
dampudløseren holdes nede, indtil dampproduktionen er blevet normal. Herefter kan dampstrygningen
fortsættes.
Damplåsfunktion
Damplåsen gør det muligt at dampstryge uden hele tiden at skulle trykke på dampudløseren.
1 Skubdamplåsenoveripositionen“ON”foratdampstygeheletiden(g.9).
- Skub damplåsen over i positionen “OFF” for at at stoppe dampstrygningen. Derved producerer
strygejernet kun damp, når du trykker på dampudløseren.
Tørstrygning (uden damp)
1 Indstildenønskedestrygetemperatur(seafsnittet“Klargøring”).
2 Strygudenattrykkepådampudløseren.
,Derslipperensmuledampud,hvisduvedetuheldkommertilattrykkepådampudløseren
under strygningen.
,Hvisdamptankenertomellerendnuikkeervarmetop,høresenklikkendelydindefra
damptanken.Deterfordidampventilenåbner,ogdeterganskeharmløst.
Funktioner
Lodret dampstrygning
Du kan også dampstryge, når du holder strygejernet i lodret stilling. Dette er ideelt til at udglatte
folder på tøj, som hænger på bøjle (f.eks. jakker, jakkesæt og frakker), gardiner og lignende.
1 Holdstrygejernetilodretstilling,ogtrykpådampudløseren(g.10).
Retaldrigdampstrålenmodpersoner.
Dampskud (kun GC6540/GC6470)
Under dampstrygning kan du bruge dampskudsfunktionen til at fjerne genstridige folder.
1 Drej temperaturvælgeren til en indstilling mellem 3og MAX.
2 Trykpådampskudsknappen.(g.11)
DANSK18
Downloaded from www.vandenborre.be

Bemærk: Brug kun dampskudsfunktionen i kortere perioder ad gangen. Hvis der drypper vanddråber ud fra
strygesålen, skal du lade strygejernet varme op i mindst et minut, inden du bruger dampskudsfunktionen igen.
Retaldrigdampstrålenmodpersoner.
Variabel damp (kun GC6540)
Dampvælgeren har trinløs regulering og kan indstilles til en hvilken som helst position mellem ECO
og ;(se afsnittet “Klargøring”).
Lysindikator for tom damptank (kun GC6540)
Når damptanken løber tør for vand under strygningen, tænder lysindikatoren for tom damptank.
1 Fyldmerevandidamptanken(seafsnittet“Klargøring-Hurtigpåfyldning”).
Lysindikator for “damp klar” (kun GC6540)
Når damptanken er klar til dampstrygning, tænder lysindikatoren for “damp klar”.
Rengøring og vedligeholdelse
Efter brug
1 Sæton/off-kontaktenpå“O”(g.4).
2 Tag stikket ud af stikkontakten.
3 Placérstrygejernetistanderen,stildampkontrollenpåECO(kunGC6540),ogladapparatet
kølened.
Strygejern
1 Rengørstrygejernetmedenfugtigklud.
2 Tørstrygesålenafmedenfugtigkludmedlidtikke-slibende(ydende)rengøringsmiddel.
Strygejernetmåaldrigkommesnedivandellerskyllesundervandhanen.
Damptank
Skyl damptanken én gang om måneden, eller efter ca. 10 ganges brug.
1 Fjernforsigtigtdamptankenslåg(g.2).
Ladapparatetkøletilstrækkeligtaf,indendufjernerlågettildamptanken.
2 Skyl damptanken med 500 ml vand.
3 Holdderefterdamptankenindovervaskenmedbundenivejretforathældevandetud(g.12).
4 Skrulågettildamptankenpåigen.
Opbevaring
1 Tagstikketudafstikkontakten,ogladapparatetkøleaf.
Kontrollér,atapparateterkølettilstrækkeligtaf,førdustillerdetvæk.
2 Tømdamptanken.
3 Kontrollérregelmæssigt,atbådenetledningenogdampslangenerheleogubeskadigede.
4 KunGC6540/GC6530r:Forsikkeropbevaringskaldulåsestrygejernetfastpåholderenmed
strygejernslåsen.Skubførstspidsen(1)ned,ogskubderefter“hælen”(2)ned(g.13).
5 Rul slangen og ledningen op hver for sig.
6 Placerslangenogledningeniopbevaringsrummet(g.14).
DANSK 19
Downloaded from www.vandenborre.be

Miljøhensyn
- Apparatet må ikke smides ud sammen med almindeligt husholdningsaffald, når det til sin tid
kasseres. Aevér det i stedet på en kommunal genbrugsstation. På den måde er du med til at
beskytte miljøet (g. 15).
Reklamationsret og service
Hvis du har brug for hjælp eller oplysninger, eller hvis der opstår et problem, skal du besøge Philips’
websted på www.philips.com/service eller kontakte dit lokale Philips Kundecenter.Telefonnumre
ndes i vedlagte “worldwide guarantee”-folder. Hvis der ikke ndes et kundecenter i dit land, bedes
du kontakte din lokale Philips-forhandler.

Dette kapitel opsummerer de mest almindelige problemer, der kan forekomme ved brug af
apparatet. Har du brug for yderligere hjælp og vejledning, så besøg www.philips.com/support for
at se en liste med ofte stillede spørgsmål, eller kontakt dit lokale Philips Kundecenter.
Problem Årsag Løsning
Der kommer røg
ud af apparatet,
første gang det
tændes.
Dette er helt normalt og skyldes, at
nogle af delene i apparatet er smurt
med olie fra fabrikkens side.
Dette ophører efter kort tid.
Der drysser
smudspartikler
ud af det nye
strygejerns
strygesål.
Det er helt normalt for et nyt
strygejern. Partiklerne er helt harmløse og forsvinder efter et par ganges brug
af strygejernet.
Der drypper
vand ud af
strygesålen.
Temperaturvælgeren er indstillet til en
temperatur, som er for lav til
dampstrygning.
Indstil en strygetemperatur, som
egner sig til dampstrygning
(temperaturindstillinger fra 2til
MAX).
Der er ikke tændt for apparatet. Stil on/off-kontakten på “I”.
Damptanken er placeret på et ustabilt
og/eller ujævnt underlag. Stil damptanken på et stabilt og jævnt underlag.
Når dampstrygningen påbegyndes, er
slangen kold. Dampen i slangen
omdannes til kondensvand, som
drypper ud gennem strygesålen.
Det er helt normalt. Hold
strygejernet hen over en gammel
klud og tryk på dampudløseren.
Kluden opsuger dråberne. Efter
nogle sekunder er
dampproduktionen normal.
Apparatet
producerer ingen
damp.
Der er ikke tændt for apparatet. Stil on/off-kontakten på “I”.
Damptanken er ikke varm nok til at
producere damp. Vent i 6 minutter, indtil damptanken er varmet op.
Du trykker ikke på dampudløseren. Tryk på dampudløseren, og hold den
nede, mens du dampstryger.
DANSK20
Downloaded from www.vandenborre.be