Philips PD9000/05 User manual

DVD Portable PD9000/05/12/51/79
Published by BL AVM Printed in the Netherlands Subject to modification
Version 2.0
TABLE OF CONTENTS
Chapter
Technical Specification, PCBs Location………………….. 1
Safety Instruction ……………………………………………… 2
Instruction for Use………………………………………………3
Mechanical and Dismantling Instructions…………………. 4
Service Modes, Troubleshooting……………………………. 5
Overall Block Diagram, Wiring Diagram…………………….6
Electrical Diagram……………………………………………… 7
Exploded View Diagram & Service Part List………………..8
Revision List……………………………………………………. 9
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may by reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronics, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Service Manual
3141 785 34840

1.0 TECHNICAL SPECIFICATION
VIDEO/AUDIO Characteristic Testing discs
Test discs：DOLBY: Dolby Test disc
ABEX: TDV-540A
VIDEO FORMAT
DVD / SVCD / JPEG / MPEG4 / DIVX3, 4,5,6(Home
theater)
AUDIO FORMAT
CD / MP3(32 - 320 kbps)
Video (PAL /NTSC)
White bar : 714mV +10%/-20%
Sync. Amplitude: 286mV ±40mV
Burst/chroma ratio: ± 15%
S/N luminance: >42 dB
POWER CONSUMPTION
Power-Supply(AC-DC Adaptor):
Supply voltage: AC 100~240V ±10%
Supply Power consumption(AC adaptor 100/240V): 9V 0.8A +10%
DC Power supply(Operate voltage range): 6.2V-15.49V±10%
Standby Power (AC adaptor, no load),264VAC: <0.75W
GENERAL DESCRIPTION
Optical Pickup: ASA PM2381-D(850PH)
Chip set/ Solution: Sunplus SPHE8202P-A ,8202PS-A
Disc Size:8cm/12cm
1-1

1.1 PCBs Location
VERSION VARIATIONS
Type/Versions:
Service policy
Board in used:
PD9000
KEY BOARD M
TFT BOARD M
*TIPS: C -- Component Lever Repair.
M -- Module Lever Repair
X -- OCX
12
MMAIN BOARD
05 51 79
M
M
M
M
M
M
M
M
M
1-2

1.2 System, Region Code, etc. Setting Procedure
Procedure to change region code of your DVD Portable
1. Power ON the DVD player and do not insert DISC inside player
2. Setup Prefer
9Æ6Æ5Æ3
The LCD display showed the existing region Code
3. Press▲(navigation up)or▼(navigation down)
repeatedly to select the number from 1 to 6.
4. Then press OK to confirm your region code.
5. Refer below table for your region code setting
Procedure for SW upgrade
1. The upgrade will provide a document re-named: PHILIPS.BIN
2. “PHILIPS.BIN” copy to CD-ROM into the data;
3. Reading the CD-ROM，in accordance with prompt，press ”OK” key to upgrade
Warning: Do not unplug the AC adapter during firmware upgrade to prevent flash corrupt of the set!!
Procedure to check SW version of your DVD Portable
1. OPEN
2. Press SETUP MENU
3. Select Preferences
4. Select Version Info
5. Press “OK” key
1-3

2.0 SAFTETY INSTRUCTIONS
GB
WARNING
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
NL
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécia-
listes agréés, seuls habilités à réparer
votre appareil en panne”.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
CLASS 1
LASER PRODUCT
3122 110 03420
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
SF
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
2-1

Whenthepowersupplyisbeingturnedon,youmaynotremovethislasercautionslabel.Ifitremoves,radiationoflaser
maybereceived.
2.1 ESD PROTECTION
PREPARATIONOFSERVICING
PickupHeadconsistsofalaserdiodethatisverysusceptibletoexternalstaticelectrocity.
Althoughitoperatesproperlyafterreplacement,ifitwassubjecttoelectrostaticdischargeduringreplacement,
itslifemightbeshortened.Whenreplacing,useaconductivemat,solderingironwithgroundwire,etc.to
protectthelaserdiodeformdamagebystaticelectricity.
Andalso,theLSIandICaresameasabove.
Solderingiron
withgroundwire
orceramictype
Groundconductive
wriststrapforbody.
Conductivemat
Thegroundresistance
betweenthegroundline
andthegroundislessthan10
1M
2-2

SAFTY NOTICE
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000 per volt or more sensitivity.
Connect a 1500 10W resistor,paralleled by a 0.15uF
150V AC capacitor between a knomn good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
SAFTY PRECAUTIONS
LEAKAGE CURRENT CHECK
Measure the AC voltage across the 1500 resistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3V.A reading
exceeding 0.3V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO PLAYER
power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE
CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO PLAYER
AC OUTLET
AC VOLTMETER
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
0.15uF 150V AC
1500
10W
(5000 per volt
or more sensitivity)
Good earth ground
such as a water pipe,
conduit, etc.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
2-3

2.2 SAFETY INSTRUCTIONS
Battery Handling Guideline
Since the battery is packed in soft package, to ensure its better performance, it’s very important to carefully handle
the battery
2.2.1 Soft Aluminium foil
The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles.
x Don’t strike battery with any sharp edge parts
x Trim your nail or wear glove before taking battery
x Clean worktable to make sure no any sharp particle
2.2.2 Sealed edge
Sealing edge is very flimsy
x Don’t bend or fold sealing edge
2.2.3 Folding edge
The folding edge is form in battery process and passed all hermetic test.
x Don’t open or deform folding edge
2.2.4 Tabs
The battery tabs are not so stubborn especially for aluminum tab.
x Don’t bend tab
2.2.5 Mechanical shock
x Don’t Fall, hit, bend battery body
2.2.6 Short
Short terminals of battery is strictly prohibited, it may damage battery.
2-4

3.0 Instruction for Use
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
3-1

Disassembly Procedure on PET941D
Remove nine screws on back cabinet
to separate top cabinet and back
cabinet. screws 9pcs
Generally open the front cabinet.
Remove 3 screws and disassemble the
connecter on the DVD LOADER.
4.0 MECHANICAL INSTRUCTION
Remove four screws and disassemble
the connecter on the Main board and
Battery. screws 4pcs.
Remove six screws on the key board.
Remove the speaker grill and 4pcs
screws. .
4-1

Remove the 2pcs screws and
disassemble the connecter on the TFT
board.
4-2

5.0 TROUBLESHOOTING
SYMPTOM: NO IMAGE / NO SOUND
SYMPTOM: NO IMAGE OUTPUT ( THE PANEL SHOW BLUE PICTURE)
Start
Check the external AV
Cable TYPEnote and
connection is OK?
Replace DVD DriveCheck DVD Drive work?
Replace Main Board
Exchange AV cable
NOTE: AV Cable TYPE from outside to
Inside L-Audio, R-Audio, Video, Ground
no
yes
no
yes
SYMPTOM: NO SOUND COMES FROM SPEAKER
Start
Check the Connection OK? Reinsertion
Check speaker OK?
Replace Main Board
Change the speaker
no
yes
no
yes
5-1

5.0 TROUBLESHOOTING
SYMPTOM: THE DVD DRIVE DOES NOT WORK
SYMPTOM: THE DVD DRIVE DOESN＇T WORK
Start
Replace DVD-
Loader
Check the DVD-Loader
OK?
Replace main board
NO
Yes
Yes
Cable ReinsertionNO
Check DVD-Loader
connection OK?
5-2

5.0 TROUBLESHOOTING
SYMPTOM: ADAPTOR CANNOT POWER ON
Start
Check Adaptor OK?
Adaptor can not Power ON
Change adaptor SET OK?
Return set to
Customer
NO
Check the Power-ON
button and cable OK? Replace Main Board
Replace Button or
Cable
Yes
NO
Yes
No
YES
OK
5-3

5.0 TROUBLESHOOTING
SYMPTOM: KEY & BOTTON FAILURE
SYMPTOM: Key & Botton Fail
Start
Check KEY board OK?
Replace main board
NO
Yes
Yes
Cable ReinsertionNO
Check CABLE form board to
board connection OK?
Return to custormerOK
Replace KEY board
OK
5-4

ASM1117_ADJ
YD4558
+1.25V
TIMING CONTROL SIGNALS
AUDIO TO SPEAKER/EARPHONE
SPI/FLASH
+5V
+9V DC TO DC
IC S701
MOTOR
DRIVER
IC
SW5888
AUDIO_R TDA2822
VGH/VGL/VCOM...
AUDIO_OUT
SPHE8202PS-A
RGB
+3.3V
AUDIO_L
+5V
+9V DC TO DC
IC S701
SDRAM
/4Mx16Bits
9'HSD ANALOG PANEL
640 X 234 X RGB
SS6610
LED DRIVER VOLTAGE
AUDIO_R
DECK
SF-HD850(870)PH-S
AUDIO_L
6-1
OVERALL BLOCK DIAGRAM

BAT_OUT
Over voltage detect
CIRCUIT DIAGRAM-CHARGE
$$$1
$$$43
$$$29
$$$17
$$$3
$$$45
N16802378
$$$7
$$$10
$$$22
$$$44
$$$36
$$$39
$$$37
$$$18
N16854012
$$$46 $$$35
$$$31
$$$47
$$$34
$$$41
$$$19
$$$26
$$$24
$$$9
$$$13
$$$6
$$$25
$$$27
$$$42
$$$8
$$$28
$$$33
$$$15
$$$32
$$$2$$$5
$$$23
$$$21
$$$40
N16802350
$$$14
CHARGE_IN
BAT_OUT
$$$38
CHARGE_IN 2
BAT_OUT 2
CHARGE_IN BAT_OUT
B2
P+5V
DR6
10R
21
DR1 680R
21
DC13
0.1UF
12
DD3
4148
12
DR2
10k
21
DQ12 3906
2
13
DC8
0.47uF
DC11
0.1UF
2 1
DC16
0.1UF
DR12
10K
21
DR41
20k_1%
21
DC14
4.7uF/0805
C/0805B
21
DC3
1000PF
12
DR51 470R
21
DR13
100k
21
DR8
10R
21
TWR3
1
+
DC21
220uF/16V
DR33 100k_1%
21
TMOD1
1
DQ5
3904 2
1 3
B+
1
DR58
330K
21
DR32
NC
21
DC2
NC
DQ15
3904 2
1 3
DC12
0.1UF
DR57
NC
21
DC15
470P
TPWM1
1
DR10
30k
21
R77
NC
2 1
DC18
1000P
DR55 1K
DR64 100K
TBM1
1
DR60
4.7KDR40
20k_1%
21
DD6 4148
1 2
DR34 NC
21
DC6
0.47uF
C/0402B
12
DIC3
8242AAY
2
1
4
5
3
6
CO
DO
VC
VCC
VM
VSS
D13
LED-A
DQ13
CEM9926A
1 2 3 45
6 7 8
DC17
0.1UF
DC25
0.01UF
C/0402B
12
TWR1
1
TDO1
1
DR53
1K
21
DR39
470
21
DR50 1K
DL1 47uH 2A 6x8
DR3 680R
21
DC4
2.2uF/0805
TB+1
1
DR56
220K
21
DR5
100R
21
R72
NC
2 1
DD5
4148
12
DR31
100K_1%
21
DR59
NC
21
DR43
1K
DR15
100k
21
DB3
HT7033
1
3
2
4
OUT
VSS
VDD
VDD2
R20
560R
DC19
NC
C/0402B
2 1
+
DC1
47uF/25V
DD2
SS34
TB-1
1
DR62
DIP 0.1 OHM 1/4W_1%
1 2
DR61
DIP 0.1 OHM 1/4W_1%
1 2
B-
1
DR52
3.3K
21
DC10
0.1UF
DR54
4.7M
21
DC41
0.1UF
DQ3
HT772J
Q
3
2 1
DC7
0.1UF
2 1
C118
0.1uF
C/0402B
12
DIC21
HT46R52A ht46r52a
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
PA3/PFD
PA2
PA1
PA0
PAO/PWM
VREF
VSS
PB0/AN0
PB1/AN1
PB2/AN2 PB3/AN3
PB4/AN4
RES
VDD
OSC1
OSC2
PA7
PA6
PA5/INT
PA4/TMR
DQ2
3904 BM1
1
DC5
2.2UF/0805
1
2
TCS1
1
DR63
1M
21
DC20
0.1UF
C/0603A
2 1
DR11
10K_1%
21
DR9 470R 21
DIC2A
CYT431W
2
3
12
3
1
TWR2
1
DC9
2.2UF/0603 C/0603A
12
DR7 1K
2 1
DR4
470
21
DQ1
9013
DR25
10k
21
7-1

EE
2N3906
1
2
B
C
2N3904
B
C
31
2
3
3
2
E
22
1B3
3
2
CC
12N3904 13 BAV992N3906
BE
1
CIRCUIT DIAGRAM-AUDIO&VIDEO
AOUT_L
AC
AOUT_R
AV-OUT-L
AV-OUT-R
AOUT_R
AOUT_L
AV-OUT-R
AV-OUT-L
CVBS
DC_IN
AC
CVBS_OUTCVBS
A_L_SPEAKER
R_HP_IN
A_R_SPEAKER
L_HP_IN
+Vcc
DC_IN +Vcc
A_R_SPEAKER
A_L_SPEAKER
R_HP_IN
VCC9
SPL
SPR
L_HP_IN
AOUT_R3 AOUT_L3
CVBS 3
DC_IN 2
VER
VER
DC_IN
R122 27K
C97
1000pF
D19
IN4148
+
EC52 10uF/16V
+
EC3
220uF/16V
C113
150P
+
EC35 100uF/16V
R119 10K
+
EC27
22uF/25V
R118 27K
R93
NC
R113
NC
R25
10k
C103
1000pF
+
-
U7A
NJM4558-SOP-8
3
21
8 4
R150
4.7R
R142 2R(0805)
TP21
R127 10K
L36 0R/0603
C95 100pF
R141 2R(0805)
C110
0.1uF
EC96
10uF_16V
+
EC28
47uF/10V
C98
NC
+ EC36
100uF/16V
C108
150P
EC95
10uF_16V
L30
OR/0603
C106
0.1uF
R144 150R
R124 100K
R146 56K
+
EC30
100uF/16V
R149
10K
C99 100pF
R151
4.7R
R139 100K
C151
0.1uF
C100
100pF
R148 150R
R121 100R
+
EC31
100uF/16V
R120
5.1K
L35 FB600R
C105
0.1uF
VJ1
speaker
1
2
3
4
1
2
3
4
R147 56K
L37 FB2K2
R140
43K
+
EC33 100uF/16V
C74 10pF
C111
0.1uF
C141
0.1uF
R192 100R
+
-
U7B
NJM4558-SOP-8
5
67
8 4
R143
680K
L34 FB2K2
R154 100K
L38 FB2K2
U9
TDA2822
1
2
3
4
5
6
7
8
R138 39K
JACK1AV/OUT-JACK
6
7
1
2
3 45
6
7
C104
NC
L32 1uH
C112
0.1uF
R123 100K
C109
0.1uF
R145
10K
VER1
earphone
1 2 34
5
6 7
8
9
10
11
C101
100pF
+
EC26 10uF/16V
+
EC32 10uF/16V
+
EC34 10uF/16V
TP20
VJ2
C10K
1
2
3
4
5
1
2
3
4
5
R126
75R
Q19 CES2307
1
2 3
+
EC29
22uF/25V
R128
5.1K
L33 FB2K2
L31 FB2K2
R103 27K
C107
0.1uF
R125 27K
7-2

For 1bit SPI Flash
0
2bit 1bit
0
R47 NC
R50 NC
SPI Mode Setting
CIRCUIT DIAGRAM-SDRAM
DQ0 DQ1
SPI_D0
SPI_D1
SPI_WP
DQ0SPI_D0
SPI_HOLD
DQ1SPI_D1
M_A5
M_A2
M_A6
M_A1
M_A8
M_A10
M_A3
M_A7
M_A9
M_A4
M_A11
M_DQM1
M_DQM0
M_WE
M_A0
M_CAS
M_RAS
M_D9
M_BA0
M_BA1
RAM_CLK
M_D4
M_D8
M_D2
M_D10
M_D7
M_D6
M_D5
M_D3
M_D14
M_D1
M_D0
M_D13
M_D12
M_D15
M_D11
M_CLK
M_BA1
M_WE
M_BA0
M_RAS
M_CAS
M_CLK
SPI_CE
SPI_CLK
DQ0
SPI_WP
SPI_CE
SPI_CLK_1
DQ1
SPI_HOLD
SPI_CLK_1SPI_CLK
RAM_CLK
SPI_D0 3
SPI_D1 3
M_A[0..11] 3
M_D[0..15] 3
M_DQM[0..1] 3
M_CAS 3
M_RAS 3
M_WE 3
M_BA0 3
M_BA1 3
SPI_CE 3
SPI_CLK 3
M_CLK 3
SPI_VCC3 SPI_VCC3
GND
SD_VCC3
GND
GND
SD_VCC3
GND
GND
SD_VCC3
GND
SPI_VCC3
GND
GND
R55 10K
0.1UF
C63
10pF
C67
EC25
100uF/10V
U6
MX25L16
1
2
3
4
8
7
6
5
/CS
DO
/WP
VSS
VCC
/HOLD
CLK
DIO
R56 10K
EC24
10uF_16V 0.1UF
C64
0.1UF
C60
R51 NC
0.1UF
C65
R52 0R
R57 0R
0.1UF
C61
R53 33R
NC
C68 0.1UF
C59
R54 0R
0.1UF
C62
0.1UF
C66
U8
SDRAM_1Mx16x4
23
24
25
26
29
30
31
32
33
34
17
18
15
16
19
37
38
39
2
4
5
7
8
10
11
13
42
44
45
47
48
50
51
53
36
20 1
27
28
41
22
40
3
9
43
49
6
12
46
52
35
21 54
14
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
CAS
RAS
LDQM
WE
CS
CKE
CLK
UDQM
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
NC
BA0 VDD
VDD
VSS
VSS
A10/AP
NC/RFU
VDDq
VDDq
VDDq
VDDq
VSSq
VSSq
VSSq
VSSq
A11
BA1 VSS
VDD
7-3

RESET
The Cover Limit Switch
UART/I2C
close to connector
SANYO HD850/870
CIRCUIT DIAGRAM-MPEG
M_BA1
M_WE
M_BA0
M_RAS
M_CAS
M_CLK
M_A11
SPI_CE
SPI_CLK
SPI_D0
SPI_D1
CVBS
AOUT_R
AOUT_L
SP-
FCO
FOC+
FOC-
SPDCO
DMEA
SLED+
SLED-
RAD+
VREF2
RAD-
TCO
SCO
XOPVIN
PUH_CDLD PUH_DVDLD
FCO
TCO
SPDCO
SCO
N20428688
M_D6
B/U
P_STHL
M_A3
XOPVIP
C
E
M_CAS
DAC_VREF
M_D13
M_D8
M_A7SPI_CLK
VREF1
M_D12 G/Y
M_A1
XOPVIN
P_OEVM_D5
AOUT_L
R/V
M_CLK
M_A9
SC_OUT
DVDLDO
M_D14 M_D10
M_RAS
K0 M_D9 VDD_33
M_A6
M_DQM0
DMEA
DA_FEO
RESET_B
VREF1
M_D0
M_A11
CDLDO
A
M_D4
VDD_33
M_BA0
M_A2
SPDC_OUT
P_CKV CLKIN
M_D3
M_D11 M_D15
M_BA1
AOUT_R
SPI_CE M_A5
M_A4
DA_TEO
OTP
DC_COM
UA_TX RESET_B
M_A8
M_A0
CDLDO
V_COMP
V_FSADJ
M_D1 UA_RX CLKOUT
F
M_D7
CVBS
M_A10
SPI_D1
DVDMDI
DCDC_VCC3
M_WE
M_DQM1
P_PWM2
VREF_2
AC_COM
SPI_D0
P_OEH
B
M_D2 K1
DVDLDO
D
COMP
K2 SDA
PUHRF
IR_IN
P_STVU DCDC_VCC3
SDA
SCL
DVDVR
CDVR
D
RAD-
RAD+
FOC+
PUH_CDLD
DVDMDI
B
C
/LDSW
PUHRF
A
F
E
VREF1
CD_VR CDVR
DVD_VR DVDVR
CD_VR
DVD_VR
SP+
TUN_5V_OFF
RESET_DEMOD
RESET_DEMOD
UA_TX
UA_RX
SLED+
SCL
KEY0
KEY3
KEY1
KEY2
KOUT1
KOUT2
KOUT3
SDA
IR_IN
V33
VGL
VGH
DVDVR#
VREF2 VREF_2
BACKL_EN
BACKL_EN
K3
VGL
CPH1
PUH_CDLD
PUH_DVDLD
P_PWM2
P-STVU
P-OEH
P-STHL
P_CKV
DC_COM
P-CKV
G/Y
B/U
AC_COM
R/V
P_STVU
P_CPH1
P_OEV
P_STHL
P_OEH
COVER_SW
VDD_33
DA_AVDD
DA_AVDD
DCDC_VCC3
DCDC_VCC3
DCDC_VCC3
RF3.3V
P-OEV
XOPVIP VGH
VDD_33
P_CPH1
TFT-3.3V
TFT-5V
COVER_SW
B/U
G/Y
R/V
K0
K1
K2
K3
KEY0
KEY1
KEY2
KEY3
SP+ HOME
FOC-
P-CKV
P-STVU
P-OEV
P-OEH
P-STHL
P_CPH1
SLED-
SP-
CDVR#
PUH_DVDLD
PUH_DVDLD#
PUH_CDLD#
ADAPTER_DET
ADAPTER_DET
LDSW HOMEN20428688
/LDSW LDSW
M_A[0..11] 4
M_D[0..15] 4
M_DQM[0..1] 4
M_CAS 4
M_RAS 4
M_WE 4
M_BA0 4
M_BA1 4
SPI_CE 4
SPI_CLK 4
M_CLK 4
M_A11 4
SPI_D0 4
SPI_D1 4
CVBS 6
AOUT_R 6
AOUT_L 6
BAT_DET 2
VGL 2
VGH 2
ADAPTER_DET 1
GND
GND
VVCC3
GND GND
VVCC3
RF3.3V
RF3.3V
M+5V M+5V
M+5V
RFGND RFGND
RFGND
RFGND
RFGND
RFGND
LD_VCC33
RFGND
RFGND
RFGND
RF3.3V
GND
DVCC3
GND
GND
GND
PLL_VDD1.2
AVCC3
GND
GND
GND
RF3.3V
GND RFGND
RFGND
A+5V
A+5V
RFGND
A+5V
RFGND
RFGND
P+5V
GND
GND GND
GND
RFGND
DVCC3
DVCC3
A+5V
DVCC3
GND
VDD_33
RFGND LD_VCC33
SPI_VCC3
RFGND
RFGND
P+5V
GND
DVCC3
PLL_VDD1.2
GND
GND
RFGND RFGND
PLL_VDD1.2
PLL_VDD1.2
PLL_VDD1.2
DVCC3
RFGND
GND
DVCC3 P+5V
GND
GND
RFGND
RFGND
GND
R175 10K
0.1uFC28
J6
CON14/1.25mm/DIP
1
2
3
4
5
6
7
8
9
10
12
11
13
14
C116
33pF
10pFC29
TP55
R60 FB600
R64 FB600
TP28
C30 33pF
R50
10K
0.1uF
C41
EC19
10uF/16V
C85NC
TP61
TP44
C53
0.1uF
0.1uF
C42
TP29
EC22
470uF/6.3V
TP50
C13
100P
TP27
EC15
100uF_10V
C7
1000P
EC18
10uF/16V
L65 FB600R
R65 FB600
TP24
10pFC33
0.1uF
C241
R49 100
TP8 VSYNC3
C82 100PF
IR2
1 2 3
CN5
NC/CON4/1.25MM/DIP
1
2
3
4
1
2
3
4
TP9FGIN
TP57
R21 FB600R
TP7
D16 1N4148 1000pFC38
J5
8PIN/1.25L
1
2
3
4
5
6
7
8
L13 10uH
R68 100R
C77100PF
C48
0.1uF
R245 FB600
0.1uF
C44
TP30
R32 4.7K
TP38
C71
100PF
R47
10K
R71 FB600
R129 200R
TP2
TP49
R19
10K
C84
1000PF
C114
0.1UF
CN6
26 25
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
18
19
20
21
22
23
24
Q10
S8550
2
3 1
EC16
10uF_16V
L23 FB600R
TP5 C
D17 1N4148
TP54
C78100PF
D15 1N4148
R46 4.7K
L14 10uH
CN4
2P/2.0
1
2
EC21
47uF/10V
R70 FB600
R244 470R
0.1uFC36
R34 150
TP58
680pFC37
R30 33
1000PF
C93
C88NC
SW1
DISC_SWITCH_TC-0030
34
21
R28 150
EC8
100uF/16V
TP39
CN3
4P/2.0
1
2
3
4
C58
0.1uF
R61 FB600
C49
0.1uF
TP10
L28 FB600R
C56
0.1uF
0.1uF
C43
0.1uF
C26
TP33
L19 FB600R
TP11
C76
100PF
R29 4.7K
0.1uFC40
R45 4.7K
TP47
R67 FB600
L18 FB600R
C79100PF
TP40
TP22 F
R37 91K
D4
1N4148
TP6 D
R79 FB600
TP34
TP18
C5
0.1UF
TP53
C73
100PF
R36 0
D6
1N4148
0.1uF
C47
TP13
XT1 27MHz
L64 FB600R
R78 FB600
R1730
TP48
R40 2.2K
C31 33pF
R66 FB600
C50
0.1uF
TP41
C75
1000PF
R23 FB600
R48 10K
R31 150
TP35
TP15
C83 100PF
100pFC6
TP26
C80100PF
D11
1N4148
R41
5.1
C70
100PF
Q9
S8550
2
3 1
TP3 A
R38 20K
R179 10K
1000pF
C24
R26 0
TP14
TP43
R44 1
TP42
C55
100PF
2200pFC32
TP36
R33 1K
TP52
TP25
C72
100PF
C17
1000P
R176 10K
U5
AM5888 5888s
17
18
12
11
16
20
15
23
8
10 19
22
28
14
13
4
525
27
26
1
24
21
2930
7
6
9
3
2
VOSL+
VOSL-
VOSP+
VOSP-
VOTK-
VNFTK
VOTK+
VINSL
Vcc1
VOLD+ Vcc2
PreGND
STBY
VOFC+
VOFC-
VINSP
VNFFC CTKerr1
BIAS
VINTK
VINFC
CTKerr2
VCTL
GND1GND2
REV
FWD
VOLD-
CFCerr2
CFCerr1
EC23
10uF_16V
C87NC
Q11
2N3904
C69
1000P
R35 10K
TP59
C81 100PF
C54
0.1uF
C51
0.1uF
R42
5.1
TP56
TP31
1uFC35
0.1UF
C23
TP12
TP37
0.1uFC39
1000PC16
R27 0
1000PC14
TP19
TP16
0.1uFC45
0.1uF
C46
R177 10K
TP46
R58 FB600
J8
6pin/1.25w
1
2
3
4
5
6
7
1
2
3
4
5
6
7
TP1
0.1uFC27
R22 10K
TP60
R69 FB600
TP32
TP4 B
R59 FB600
R24 FB600
TP51
R39 2.2K
U4
SPHE8202PS-A
102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 78 75 76 77
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
64
63
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
1 2 3 4 5 6 7 8 9 10 11 13 15 12 14 29 33 34 35 36 37 38 16 17 18 19 20 21 22 23 24
65 79 80 81 82 74 73 72 71 70 69 68 67 66
62
25 26 27 28 30 31 32
129
130
CDE
CDF
DVDA DVDB
DVDC DVDD
RFIS
AD_AVDD
LDSW
HOME/CARD_RST
CLKOUT
CLKIN
PLL_VDD12
USB_DM
USB_DP
USB_AVDD
COMP
FB
DCDC_PWM
DCDC_VCC3
VDD12
TCON_STVU
TCON_CKV
TCON_OEV
OPVIP
OPVIN
DVDLDO
CDLDO
MDI
SRV_AVDD
V21
V165
VDDQ
DA_TEO
DA_FEO
DA_AVDD
SPDC_OUT
SC_OUT
DMEA
FGIN
DVDVR/SCL/GPIO74
CDVR/SDA/GPIO75
CARD_SENSE/GPIO80
SPI_CE
SPI_D0
SPI_CLK
SPI_D1
SD_D0/MS_D0
SD_CLK/MS_CLK
SD_CMD/MS_BS
TCON_AC_VCOM
AOUT_R
ADAC_AVDD
VREF
AUDIO_MUTE/GPIO54/HSYNC(3)
SPDIF_OUT/GPIO53/VSYNC(3)
M_A3
M_A2
M_A1
M_A0
M_A10
M_BA1
M_BA0
M_RAS
M_CAS
M_WE
M_DQM0
M_A4
M_A5
M_A6
M_A7
M_A8
M_A9
M_A11
M_CLK
RESET_DEMOD TS_ERR VDD_33 RESET_B TS_SYNC TS_DATA TS_DEN TS_CLK VDD12 GPIO7/HSYNC(1) GPIO8/VSYNC(1) GPIO10 GPIO12 GPIO9 GPIO11 M_D15 M_D11 M_D10 M_D9 M_D8 M_DQM1 VDD_33 GPIO13 GPIO14 GPIO15 GPIO16 IR/GPIO17 M_D0 M_D1 M_D2 M_D3
TCON_DC_VCOM
TCON_OEH
TCON_STHL
TCON_CPH1
TCON_PWM
VDD_33
TV_DAC3 TV_DAC2 TV_DAC1
TV_AVDD TV_AVDD
TV_DAC0
V_FSADJ
VCOMP
AOUT_L
M_D4 M_D5 M_D6 M_D7 M_D14 M_D13 M_D12
GND
GND
R43 10K
C25
0.1uF
TP62
R243
91K
EC20
47uF/10V
R76 FB600/NC
TP45
C86NC
0.1uF
C34
TP23 E
R178 10K
EC17 10uF_16V
TP17
7-4