Philips SRP6011 User manual

TAPR802
Register your product and get support at
www.philips.com/support
User manual
Universal Remote
SRP6011

1EN
Contents
1 Your universal remote 2
Introduction 2
Overview of the universal remote 2
2 Get started 3
Insert batteries (not included) 3
Set up the universal remote 3
3 Use your universal remote control 6
Learning 6
4 Notice 7
Disposal of your old product and battery 7
5 Service and support 8
Frequently asked questions 8
Need help? 8
Contents

2EN
1 Your universal
remote
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome
Introduction
With the universal remote, you can use it to
operate your device.
Overview of the universal
remote
LIST
FAV AUDIO
HOME
BASS
TREBLE
TREBLE
BASS
SMART
MENU BACK
1
2
3
4
5
6
7
8
a: power on or off.
bAMBLIGHT: switch the amblight on/off.
LIST: open the channel list.
SLEEP: sleep timer
FAV: access the favorite channel list.
OPTIONS: access the options menu.
AUDIO: select the audio channel.
c: stop
: pause
: record
: rewind
: play
: fast forward
d: previous track
STREAM: shortcut to Netix or other App.
: next track
eHOME
SMART: SMART TV, My App or Apps.
MENU: menu on or off.
BACK: go back one menu level.
OK: conrm your selection.
TREBLE/BASS: select the sound preference.
/ //: scroll the menu up/down/
left/right.
fCH+/- go to the next/previous channel.
: select available source inputs (antenna,
cable, etc.).
: volume down
: mute
: volume up
g: subtitle
: return to the previous tuned channel.
: screen format
: teletext off
: teletext mix
: teletext on
Red/Green/Yellow/Blue: context sensitivity
buttons.
hDigit buttons
I/II : select the audio channel.
-/-- : select between one and two-gure
channel numbers.

3EN
2 Get started
Insert batteries (not included)
Warning
• Check the battery polarity when inserting in the
battery compartment. Incorrect polarity may damage
the product.
Caution
• Risk of explosion! Keep batteries away from heat,
sunshine or re. Never discard batteries in re.
• Risk of decreased battery life! Never mix different
brands or types of batteries.
Note
• When you replace the batteries, all user settings will
be retained in the memory of the universal remote for
5 minutes.
Set up the universal remote
You must rst set up the universal remote
before operating your device.
Set up by code selection
1 Switch on your device.
2 Press and hold 1and 6at the same time
for 5 seconds until the red LED is on.
3 Look up the 5-digit code for your brand
in the code list. Codes are listed by the
device type and brand name.The most
popular code is listed rst.
12345

4EN
4 Enter the rst 5-digit code using the digit
buttons.
5 If the light is off, a valid code is saved.
Otherwise, the light will ash six times, and
then remains on for code re-entry.
LIST
FAV AUDIO
HOME
BASS
TREBLE
TREBLE
BASS
SMART
MENU BACK
6 Operate the device with the universal
remote. If your device responds correctly,
it means you have entered the right code.
Otherwise, repeat from Step 2, and enter
the second code on the list.
Note
• It is possible sometimes that your device only responds
to some of the buttons. In such case, set up with the
next code in the code list, and try operating your
device again. If there spill problem on code or key, you
can try to learn a key by learning faction if the remote
support learning function.
Auto registration
1 Switch on your device.
2 Press and hold 1and 6at the same time
for 5 seconds until the red LED is on.
3 Point at your device with the universal
remote.Then press and release to
start searching the code for your brand.
A different infrared signal is sent every 2
seconds as the universal remote searches,
indicated by a blue ash.

5EN
LIST
FAV AUDIO
HOME
BASS
TREBLE
TREBLE
BASS
SMART
MENU BACK
4 When the device is off, immediately press
and release OK to save the code.The blue
LED indicator will turn off.
max. 20
minutes
LIST
FAV
AUDIO
HOME
BASS
TREBLE
TREBLE
BASS
SMART
MENU
BACK
LIST
FAV
AUDIO
HOME
BASS
TREBLE
TREBLE
BASS
SMART
MENU
BACK
5 Operate the device with the universal
remote. If your device responds correctly, it
means you have saved the right code.
Note
• Auto registration can be reversed, by pressing and
releasing once more during the auto registration
process.This is helpful if you missed out the chance to
press OK within 2 seconds. Make sure that the device
is rst powered on again.
• It is possible sometimes that your device only responds
to some of the buttons. In such case, set up with the
next code in the code list, and try operating your
device again.

6EN
3 Use your
universal
remote control
Learning
You must have an original remote for the
Universal Remote Control (URC) to learn code
from it.
Learn commands
1 Press and hold 1and 6at the same time
for 5 seconds until the red LED is on.
2 Enter the learning code 99900.
The red LED light will ash once and then
remains on.
3 Place the URC and the original remote,
head to head aiming at each other, on a at
surface.
4 On the URC, press the button that you
would like to learn a code from the
original remote. The LED will ash twice
and stay on.
5 On the original remote, press and hold the
button that you would like to learn from
for 2 seconds.
6 The LED will blink once and stay on if the
learning was successful.To learn another
key, repeat Step 4.
To exit, press 1and 6at the same time.
7 The LED will blink 6 times quickly if
learning failed. Repeat Step 4 to learn again.
Note
• On step 4, if no key is selected for more than 15
seconds, the LED indicator will ash six times and the
learning mode will exit automatically.
• On step 5, if no other remote signal is received for
more than 30 seconds, the LED indicator will ash
six times and then remains on. You will need to select
a desired key again for learning as in step 4 on your
universal remote control.
• Each function key will hold only one command, a new
command to be learned will automatically replace the
previous one.
Clear learned commands
Clear all codes learned for the universal
remote control
1 Press and hold 1and 6at the same time
for 5 seconds until the red LED is on.
2 Enter the learning code 99920.The
red LED light will remain on briey, ash
twice and then turns off.
» All codes learned for the universal
remote control will be cleared.

7EN
4 Notice
Disposal of your old product
and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Removing the disposable batteries
To remove the disposable batteries, see section
‘Insert batteries’.
When this logo is attached to a product, it
means a nancial contribution has been paid to
the associated national recovery and recycling
system.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.

8
operators can help you determine whether
SRP6011 is working properly.
You will nd our contact details at the end of
this user manual. For online support, visit
www.philips.com/support
5 Service and
support
Frequently asked questions
My universal remote does not work at all.
• Check if you have correctly setup the
device with the right code. Check if you
have pressed the corresponding device key
for your device.
• Check if the batteries are inserted properly.
If the battery level is low, replace the
batteries.
• Check if your device is powered on.
If several device codes are listed under the
brand of my device, how can I select the
correct device code?
To seek the correct device code, test the codes
one by one.The codes are sorted by popularity,
and the most popular code is listed rst.
My device responds only to some of the
commands.
You have set a code for which only some
commands work properly but some do not.Try
other codes until most keys work properly or
learn the key from original remote if it support
learning function.
Need help?
We advise you to rst read this user manual
carefully. It helps you set up and use the
universal remote.
If, however, you require extra information or
have additional questions about setup, usage,
warranty, etc of the SRP6011, you can always
contact us.
When calling our helpline, make sure to have
the SRP6011 at hand when you call, so that our
EN

Specications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the
responsibility of MMD Hong Kong Holding Limited or
one of its afliates, and MMD Hong Kong Holding Limited is
the warrantor in relation to this product.
SRP6011_10_UM_V1.0