Philips AquaTrio Cordless 9000 Series User manual

English 6
Deutsch 50

English
6English
Contents
Introduction _______________________________________________________________________________ 6
General description_________________________________________________________________________ 6
Before first use_____________________________________________________________________________ 7
Charging __________________________________________________________________________________ 10
Vacuuming and moppig hard floors __________________________________________________________ 11
Vacuuming soft and hard floors ______________________________________________________________ 15
Cleaning the Vacuum & Mop set-up __________________________________________________________ 20
Cleaning the Vacuum only set-up ____________________________________________________________ 29
Display icons and their meaning______________________________________________________________ 36
Replacement ______________________________________________________________________________ 39
Troubleshooting ___________________________________________________________________________ 40
Using the Vacuum only set-up _______________________________________________________________ 46
Introduction
Thanks for buying this Philips product! To fully benefit from the support that
Philips offers, register your product at www.philips.com/myvacuum9000s.
General description
1 Dust bucket release button
2 Display
3 Left button (1st power setting)
4 Right button (2nd power setting)
5 Middle button (AUTOCLEAN)
6 On/off button
7 Battery
8 3-in-1 handheld
9 Dust bucket
10 Wall mount
11 Tube
12 LED nozzle
13 Mini Turbo brush
14 Long crevice tool
15 Adapter
16 Power plug
17 Extra charger (XW9385 only)
18 After-Clean & Storage station
19 Appliance holder
20 After-Clean tray
21 Baseplate
22 Wet module
23 Dirty water tank
24 Clean water tank
25 AquaSpin nozzle
26 Microfiber brushes
27 Philips Floor Cleaner XV1792
28 Cleaning brush

7
English
Before first use
Assembling the After-Clean & Storage station
In order to use the AUTOCLEAN function or store and charge the appliance on
the After-Clean & Storage station, you need to first assemble the station by
clicking the appliance holder into the baseplate.
Tip: It is possible to slide the holder for Vacuum only set-up and put it back
upside down if you want to place the Vacuum only set-up on the other side of
the After-Clean & Storage station.
Note: Make sure that the After-Clean tray is placed in the baseplate and that
the temperature in the room where the appliance is stored, charged and cleaned
is between 5 °C and 35 °C.
Tip: You can hang the cleaning brush on the hook of the appliance holder.
Installing the wall mount

8English
If you want to store and charge the Vacuum only set-up on the wall mount,
fasten the wall mount to the wall with the screws supplied. Make sure the wall
mount is 140 - 150 cm above the floor.
Note: It is not possible to store the Vacuum & Mop set-up on the wall-mount.
It is only possible to store the Vacuum only set-up on the wall mount.
Note: Make sure that the temperature in the room where the appliance is
stored or charged is between 5 °C and 35 °C.
Caution: Be careful when you drill holes in the wall to fasten the wall
mount, to avoid the risk of electric shock.
Assembling the Vacuum & Mop set-up
1To assemble the Vacuum & Mop set-up, insert the battery and attach the
3-in-1 handheld to the wet module ('click').
2Attach the wet module to the AquaSpin nozzle ('click').
3To store the Vacuum & Mop set-up, you can place it in the After-Clean &
Storage station.
Note: It is not possible to store the Vacuum & Mop set-up on the wall-mount.
It is only possible to store the Vacuum only set-up on the wall mount.

9
English
Assembling the Vacuum only set-up
1To assemble the Vacuum only set-up, attach the 3-in-1 handheld to the dust
bucket ('click').
2Attach the dust bucket to the tube ('click').
3Insert the tube into the LED nozzle.
4To store the Vacuum only set-up, place it in the After-Clean & Storage station
by first placing the LED nozzle onto the long side of the baseplate and then
pressing the tube into the holder.
Tip: It is possible to slide the holder for the Vacuum only set-up and put it back
upside down if you want to place the Vacuum only set-up on the other side of
the After-Clean & Storage station.

10 English
Charging
The appliance is equipped with a 25 V Li-Ion battery. Charging takes 4 hours.
1To charge the appliance, insert the power plug into the socket on the back of
the appliance. Then insert the adapter into the wall socket.
2A value between 0% and 90% flashes on the screen to indicate that the
appliance is charging.
3When the appliance is fully charged, the value 100% lights up on the screen.
After a few minutes, the display will switch off.
Warning: Store and charge the appliance at a temperature
above 5°C and below 35°C.

11
English
Tip: You can charge the appliance when it is attached to the the wall
mount.
Tip: You can charge the appliance in the After-Clean & Storage station.
Tip: You can charge the appliance separately in a place that suits you best.
Vacuuming and moppig hard floors
Using the Vacuum & Mop set-up
The clean water tank and the dirty water tank are already attached to the
appliance upon delivery. With the wet module attached to the AquaSpin nozzle,
you can clean hard floors.
Note: This Vacuum & Mop set-up is suitable for vacuuming and mopping at
the same time. It is not necessary to vacuum the floor before mopping.
The Vacuum & Mop set-up is suitable for vacuuming and mopping all types of
hard floors, except uncoated wooden floors (see 'Usage restrictions').

12 English
1To assemble the Vacuum & Mop set-up, insert the battery and attach the
3-in-1 handheld to the wet module ('click').
2Attach the wet module to the AquaSpin nozzle ('click').
3Push the button to unlock the clean water tank and remove the clean water
tank.
4Remove the cap from the clean water tank.
5Add 10 ml of the XV1792 Philips Floor Cleaner to the clean water tank.