Philips EasyStar FC8802 User manual
FC8802
FC8800
User manual
1
2 3 4 5
6 7 8 9
10 11 12 13
14 15 16 17
18 19 20 21
6
Important
Read this user manual carefully before you use the robot and save it for
future reference. Read all the warnings and safety issues below before you
use the robot.
Danger
- Do not immerse the robot or the adapter in water or any other liquid.
-
contact with water or immersion in water.
-
-
- Do not pour any liquid into the openings of the robot.
Warning
-
mains voltage before you connect the adapter.
-
maintaining the appliance.
- Do not use the robot if the adapter or the robot itself is damaged or if
the robot is not complete.
- If the adapter is damaged, you must have it replaced by Philips, a service
avoid a hazard.
- Only replace the rechargeable battery with one of the original type.
- Never attempt to repair the robot yourself.
- This robot is designed for indoor household use only. Keep all doors
leading outside closed.
-
showers or swimming pools.
-
- This appliance can be used by children aged 8 or above and by persons
use of the appliance or supervision to establish safe use and if they have
been made aware of the hazards involved.
- Do not allow children to play with the appliance.
- Children are only allowed to empty the dust container and to clean and
maintain the robot under supervision.
-
Keep pets away from the robot. Do not let pets sit or stand on the robot.
-
Keep loose clothing, hair and body parts away from the brushes of the robot.
ENGLISH
-
robot does not get entangled in the pull cords of blinds or curtains.
- Do not let the robot move over the mains cords of other appliances or
other cables as this may cause a hazard.
- Switch off the robot if a dangerous situation occurs or if the
robot behaves abnormally or gives off an abnormal smell.
-
the dust container or has not been placed properly in the dust container.
-
robot is cleaning.This may cause the robot to overheat.
-
sure the drop-off sensors are cleaned regularly. If the drop-off sensors
are covered or dirty, the robot may fall down the stairs.
- Do not store the robot at a temperature above 60°C or below -10°C.
- Do not use the robot in a room with a temperature above 45°C.
- Do not incinerate, disassemble or expose the rechargeable battery
to temperatures above 60°C.The rechargeable battery may explode
if overheated.
Caution
-
drop-off sensors are used to detect and avoid height differences. In some
sensors may not detect a staircase or other height difference in time.
Therefore avoid using the robot in these situations or monitor it carefully.
-
- Do not touch the rechargeable battery or the adapter with wet hands.
- Only use the adapter and the rechargeable battery supplied to charge
the robot.
- Always switch off the robot before you move or store it.
- Remove the rechargeable battery from the robot if you are not going
to use it for some time. Store the rechargeable battery in a dry and safe
place if you remove it.
- Do not use the robot on high-pile carpets or on rugs with tassels.
- Do not clean the dust container with water or in the dishwasher.
(EMF). If handled properly and according to the instructions in this user
ENGLISH 7
Your robot
Congratulations on buying this robot vacuum cleaner.This slim and smart robot is ideal for cleaning
1 Dust container compartment cover
2 Top ventilation grille
3 Dust container lid
4 Filter
5 Dust container
6 Display with indicators
7 Dust container compartment
8 Rechargeable battery
9 Rechargeable battery cavity
10 Fan
11 Side ventilation grille
14 Bumper
15 Bumper strip (FC8802 only)
16 Small plug
17 Adapter
18 Side brushes
19 Suction opening
20 Wheels
21 Wheel covers
22 Bottom ventilation grille
23 Side brush shafts
24 Drop-off sensors
25 Front wheel
26 Spare side brushes (FC8802 only)
your home.
-
ENGLISH8
-
opening into the dust container (Fig. 3).
The robot uses a systematic cleaning strategy that consists of three cleaning patterns.
1 Straight pattern
2 Spiral pattern
3 Wall-following pattern
The robot uses these patterns in the following order:
1 A straight pattern, followed by a spiral pattern (Fig. 4)
2 A wall-following pattern, followed by a spiral pattern (Fig. 5)
When the robot has completed this sequence of patterns, it starts moving in straight lines again.
The robot continues to use this sequence of patterns to clean the room until the rechargeable
battery is empty, or until it is switched off manually.
- These drop-off sensors are used to detect and avoid height differences. In some cases, depending on
difference in time.Therefore avoid using the robot in these situations or monitor it carefully (Fig. 6).
1 Unpack the side brushes.
2 Push the side brushes onto the shafts on the bottom of the robot (Fig. 7).
Note: Make sure you attach the side brushes properly. Press them onto the shaft until you hear them
lock into position with a click.
You have to insert the rechargeable battery before use.
1
2
3
4
connector (Fig. 10).
5
6
Note: Make sure the two cover latches slide into the appropriate holes in the housing of the robot.
been inserted properly (see chapter ‘Using your robot’, section ‘Indicator signals and their meaning’).
Charge the battery for at least 4 hours each time to ensure the rechargeable battery performs best
and has a long life. A fully charged battery gives you a cleaning time of approximately 50 minutes on
ENGLISH 9
Charging
1
2
3
4
Note: It is possible that the on/off switch is still in ‘on’ position while charging. In that case, the robot will
not work when you press the on/off switch once to start a new cleaning run.You have to press the on/off
switch a second time to switch on the robot.
Preparing for cleaning
1
2
Note:The robot does not operate when it is connected to the mains.Therefore, always disconnect the
adapter from the robot and the mains before use.
Note:Always store the adapter in a safe place before you switch on the robot.
3
4
or rugs to see how it is coping.
Cleaning
1
detect a staircase or height difference in time.
,
2
beeps. Recharge the robot to continue cleaning (see chapter ‘Preparing for use’, section
‘Charging’) (Fig. 14).
ENGLISH10
The robot has a display with three indicators: the battery indicator, the dust compartment indicator
and the warning indicator.The table below explains the meaning of the signals these indicators give.
Meaning
The battery indicator lights up continuously. The robot is cleaning.
The robot is charging.
beeps twice every minute. The rechargeable battery is empty.
The dust compartment indicator lights up
continuously. The dust compartment cover is missing.
The dust container is not present.
beeps twice every minute. The robot was switched on while it was
dust in the dust container. For the best results, we advise you to empty and clean the dust container
after each use.
1
2
3
4 Take the dust container out of the dust container compartment (Fig. 19).
Note:When you remove or reinsert the dust container, take care not to damage the blades of the
motor fan.
5
6
7
8
9
10 Put the dust container back into the dust container compartment (Fig. 25).
ENGLISH 11
11
drop-off sensors in the bottom of the robot.To maintain good cleaning performance, you have to
clean the suction opening, the wheels and the drop-off sensors from time to time.
1
2
3
opening (Fig. 26).
4
5
Note: It is important that you clean the drop-off sensors regularly. If the drop-off sensors are dirty, the
robot may fail to detect height differences.
To ensure proper functioning, clean the side brushes and the shafts from time to time.
1
2
3
4
5
6 Push the side brush back onto the shaft (Fig. 31).
7 Repeat steps 2 to 5 for the other shaft and the other side brush.
Storage
1
2
3
4
Note:After a long period of storage, always charge the robot before you switch it on.
Replacement
1
ENGLISH12
2
3
container (Fig. 32).
4
5
Replace the side brushes after some time to ensure proper cleaning results.
Note:Always replace the side brushes when you notice signs of wear.We also recommend that you
replace both side brushes at the same time.
1
2
3
4
5 Repeat steps 3 and 4 for the other side brush.
Replacing the rechargeable battery
Replace the rechargeable battery when you can no longer recharge it or when it runs out of power
1
2
3
4
connector (Fig. 35).
5
To purchase accessories for this appliance, please visit our online shop at
Environment
- The rechargeable battery contains substances that may pollute the environment.Always dispose
rechargeable battery is completely discharged when you dispose of it.To completely discharge
the rechargeable battery, let the robot run until the battery is completely empty. Always remove
ENGLISH 13
- Do not throw away the robot with the normal household waste at the end of its life, but hand it
environment (Fig. 37).
If you need service or information or if you have a problem, please visit the Philips website at
or contact the Philips Consumer Care Centre in your country.
Your robot has been designed and developed with the greatest possible care. In the unfortunate
case that your robot needs repair, the Consumer Care Centre in your country will help you by
arranging any necessary repairs in the shortest possible time and with maximum convenience.
If there is no Consumer Care Centre in your country, go to your local Philips dealer.
- The guarantee for the rechargeable battery is restricted to 6 months.
This chapter summarises the most common problems you could encounter with the machine. If you
are unable to solve the problem with the information below, visit for
Cause
The robot does
not start cleaning
when I press the
The rechargeable
battery is empty. Charge the rechargeable battery (see chapter
‘Preparing for use’, section ‘Charging’).
The small plug is still
on the robot.
disconnected the adapter from the robot and the
mains before use.
The robot does
dust
compartment
indicator lights up
continuously.
The dust container
compartment cover is
not present or is not
closed properly.
When the dust container compartment cover is not
present or is not closed properly, the robot does not
dust compartment cover on the robot properly
rechargeable battery’).
The dust container is
not present. Place the dust container in the dust container
dust container compartment cover properly.
The robot starts
to move
cleaning or just
after it was
switched on.The
warning indicator
The bumper of the
If the robot manages to free its bumper by moving
the robot starts cleaning normally. If the robot does
not manage to free its bumper, switch it off and lift it
so that its bumper comes free.Then switch on the
robot again.
ENGLISH14
Cause
The warning
One or both wheels
around the wheel suspension.
One or both side
Clean the side brushes (see chapter ‘Cleaning and
maintenance’, section ‘Cleaning the side brushes’).
the robot so that its bumper comes free.
The robot was lifted
while it was cleaning.
The robot does
not clean
properly.
The bristles of one or
both side brushes are
Replace the side brushes (see ‘Replacing the side
brushes’ in chapter ‘Replacement’ and chapter
‘Ordering accessories’).
container is dirty.
with soft bristles (see chapter ‘Cleaning and
maintenance’, section ‘Emptying and cleaning the dust
container’)
accessories’).
The suction opening
in the bottom is
clogged.
Clean the suction opening (see chapter ‘Cleaning
and maintenance’, section ‘Cleaning the suction
opening, the wheels and the drop-off sensors’).
The front wheel is
jammed with hair or
other dirt.
Clean the front wheel (see chapter ‘Cleaning and
maintenance’, section ‘Cleaning the suction opening,
the wheels and the drop-off sensors’).
The robot is cleaning
triggers the drop-off
sensors.This causes
the robot to move in
an unusual pattern.
the Consumer Care Centre in your country.
The robot is cleaning
sunlight quite strongly.
This triggers the
drop-off sensors and
causes the robot to
move in an unusual
pattern.
the room.
The battery can
no longer be
charged or runs
empty very fast.
The rechargeable
battery has reached
the end of its life.
Replace the rechargeable battery (see chapter
‘Replacement’, section Replacing the rechargeable
battery’ and chapter ‘Ordering accessories’).
ENGLISH 15
16
Vigtigt
Fare
-
-
-
-
-
-
-
af apparatet.
-
eller hvis robotten mangler dele.
-
-
-
-
-
-
-
-
-
robotten under opsyn.
-
-
-
-
DANSK
-
-
-
-
-
-
-
- Robotten er udstyret med tre sensorer i bunden. Disse sensorer bruges
-
-
-
batteri til at oplade robotten.
-
-
hvis det tages ud.
-
-
Din robot
welcome.
DANSK 17
2 Øverste ventilationsgitter
4 Filter
8 Opladeligt batteri
9 Rum til genopladeligt batteri
11 Sideventilationsgitter
17 Adapter
20 Hjul
22 Bundventilationsgitter
24 Sensorer
25 Forhjul
-
-
DANSK18
Robotten er udstyret med tre sensorer i bunden.
-
1 Pak sidebørsterne ud.
2
plads med et klik.
1
2
3
4
5
6
1
2
3
4
DANSK 19
1
2
robotten og stikkontakten inden brug.
3
4
nærheden af tæpper for at se, hvordan den klarer opgaven.
1
,
2
Robotten oplades.
DANSK20
Other manuals for EasyStar FC8802
5
This manual suits for next models
1
Table of contents
Languages:
Other Philips Vacuum Cleaner manuals
Philips
Philips FC8149 User manual
Philips
Philips PerformerPro FC9190 User manual
Philips
Philips City Line Helsinki FC8408 User manual
Philips
Philips FC6141 User manual
Philips
Philips Specialist User manual
Philips
Philips FC6901/01 User manual
Philips
Philips SilentStar FC9306 User manual
Philips
Philips Easy Clean FC8736 User manual
Philips
Philips Marathon FC9200 User manual
Philips
Philips FC8149 User manual
Philips
Philips FC 6842/A User manual
Philips
Philips FC6132/02 User manual
Philips
Philips FC9066 User manual
Philips
Philips Performer Active FC8653/01 User manual
Philips
Philips FC6840 series User manual
Philips
Philips FC9310 User manual
Philips
Philips AquaTrio Cordless 7000 Series User manual
Philips
Philips FC8740 User manual
Philips
Philips FC8146/71 User manual
Philips
Philips FC6145 User manual
Popular Vacuum Cleaner manuals by other brands
iRobot
iRobot Roomba Combo j5 user manual
SharkNinja Operating
SharkNinja Operating Shark Rotator Powered Lift-Away ZU630 Series owner's guide
Numatic
Numatic AST74 Original instructions
Numatic
Numatic PPR 180-11 Original instructions
Bissell
Bissell POWERFORCE HELIX TURBO REWIND PET 2692... user guide
Gorenje
Gorenje VCEA23GLR instruction manual
