Philips FC9025 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Universe Vacuum cleaner
FC9025
03/03
PRODUCT INFORMATION
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Colour : Violet
- Maximum air displacement : 37 l/sec.
- Maximum vacuum water column : 310 cm
- Power consumption (IEC) 230 V : 1500 W
- Duststorage capacity : 3 L
- Type number dustbag : FC8021
- Cord length (depends on version) : 7 metres
- Filter system : Paper dustbag
: Exhaust AFS air filter
: Motor inlet filter
- Dimensions of cleaner : 460 x 315 x 270 mm
- Dimensions of packaging : 595 x 395 x 295 mm
- Net weight : 5.88 kg
- Gross weight : 9.135 kg
OPTIONAL (accessories)
- FC8021 S-bags
- FC8030 AFS-filter
- FC8031 HEPA Air Filter
- FC8034 Upgrate kit Active Carbon Filter
- FC8042 Polishing nozzle
- FC8043 Turbo brush nozzle
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- Open the appliance, first remove the exhaust filter grille
(item 20), and then remove the 2 screws - Cof the switch
control panel (item 15).
- To remove the the panel, pos 14a + b must be removed by
using a screwdriver to separate the two covers from the panel
as shown in the picture.
- Undo and remove the 9 screws (T15) - Cin the upper
housing (item 8). You will require a screwdriver with a
14.5 cm-long shank for this. Srewdriver 4322 009 08490
can be used.
- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.
- When the repair is finished, check whether all functions of
the appliance work properly.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10; T9;
T8; T7 and T6 (code number 4822 395 50145).
C2x
C9x 14a + b

FC9025
REPAIR INSTRUCTION
- Item 4, cotton dustbag, is used in countries in which paper
dustbags are not available.
- If the reel half spring unit is replaced, shaft Amust be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (43) or conductors
(42).
- Item 40 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- Item 13, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.
- If the function of the electronic control unit (item 12) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, eventhough the dustbag is not
full at all.
- Due to introduction of a new switch (item 11) 0320
onwards, which is not interchangable with the old switch
soldered on the PCB (item 12).
- The switch lever assy (item 11a) is also modified.
To recognize the switches:
New spares are:
Switch soldered version - 4322 006 50600
Switch lever assy - 4322 009 08980
ELECTRICAL DIAGRAM
Old New
∅13 mm ∅10 mm
M
MOTOR
POWER
MODULE
Black
Black
Blue
Brown
CORD WINDER
Short-circuit
Triac
2-7

FC9025
PARTS LIST
3-7
Pos Service code Description
1
2
3
4
5
6
7
8
8a
9
10
11
11a
12
13a
13b
14a
14b
15
16
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
4322 005 14540
4322 003 21620
4322 003 21730
4822 480 10113
4322 004 93290
4322 003 18300
4322 001 73310
4322 005 12550
4322 003 21610
4322 003 21740
4322 000 37300
4322 009 07040
4322 006 21480
4322 006 50600
4322 009 08420
4322 009 08980
4322 006 22560
4322 005 12200
4322 005 12210
4322 003 21710
4322 003 21700
4322 009 08650
4322 003 21600
4322 000 37450
4322 005 12190
4322 009 08590
4322 000 37460
4322 004 92910
4322 001 73280
4322 003 18000
4322 000 37420
4322 000 37430
4322 003 21660
4322 003 18910
4322 003 20390
4322 003 21690
4322 001 73300
4322 003 18040
4322 003 18010
4322 003 18020
Dust cover Violet
Dust cover lock c.grey
Dustbag holder s.grey
S-paper dustbags FC8021
Cotton dustbag
Cordwinder lever
Sealing rim
Dustbag detector
Upper housing c.grey
Clamp upper/lower housing
Triple filter
Grill + triple filter
Switch soldered version
Switch sold. vers. 0320 onwards
Switch lever assy
Switch lever assy 0320 onwards
PCB slide turn 230V
Dustbag full indicator
Air valve
Cover R c.grey
Cover L c.grey
Panel assy turn Violet
Lower housing c.grey
Silencer 4 wall
Caster assy m.grey
Exhaust grille c.grey
Exhaust diffusor (opt.)
Electr.static filter FC8030
Filter sealing
S-class sealing
Silencer 1 wall
Silencer 2 bottom
Cord outlet c.grey
Rear wheel lock red
Receipt. housing A.C.
Rear wheel c.grey
Motor buffer back
Inlet sealing
Motor cap top
ANS disc
Pos Service code Description
35
36
37
38
40
41
42
43
44
45
46
47
48
49
50
51
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
A
B
C
4322 001 73290
4322 009 06430
4322 000 37440
4322 003 18030
4322 009 07940
4322 001 72360
4322 009 07950
4322 009 07970
4322 006 01440
4322 006 01760
4322 006 01680
4322 006 01720
4322 006 01410
4322 006 01670
4322 006 01460
4322 003 18850
4322 005 13510
4322 007 16000
4322 004 22570
4322 003 18870
4322 005 13410
4322 004 41140
4322 004 22510
4322 001 99120
4322 007 45550
4322 004 22560
4322 004 22490
4322 004 22970
4322 005 11040
8838 041 01010
9965 000 03349
4822 358 10205
4822 479 20201
4322 004 22590
5322 390 20011
4322 002 82550
2522 200 02018
Motor bufferring front
Motor A 1441 230V
Silencer 3 ans
Motor cap bottom
Reel half spring unit (L = 9m)
Brake tyre
Reel half contact unit
Contact ring plate
Argentina L = 9.3 m
Australia L = 9.3 m
Taiwan L = 6.3 m
U.K. / H.K. L = 9.3 m
Euro 4.8 mm pins L = 9.3 m
Swiss L = 9.3 m
Italy L = 9.3 m
C-bend B1
C-bend B1 hose assy
Leaf spring assy
Plumeau assy (opt.)
Crevice nozzle
Acc. bridge assy
Metal tube (opt.)
Telesc. tube
Tube bush
Tube spring
Small nozzle
R&C nozzle standard l.grey
Polishing nozzle
Polishing disc
Polishing brushes
Coupl. piece (standard) (opt.)
Drive belt (opt.)
Brush assy (opt.)
Turbo nozzle (opt.)
Silicon grease for shaft
Screw 3.5 x 12 T10
Screw 3.5 x 19 T15

FC9025
EXPLODED VIEW
ZY
C
1
3
2
4
8a
5
6
8
7
11
11a
9
10
12
13a
13b
18
20
21
22
23
15
14a
14b
4-7

FC9025
EXPLODED VIEW
Y
black
Z
brownblue
43
44÷49
33
34
35
36
37
38
28
24
25
26
27
32
42
B
A
40 41
B
16
19
30
29
31
5-7

FC9025
EXPLODED VIEW
60
61
56
55
57
54
58
60
61
65
64
66
59
44
Argentina
Australia
Taiwan 45
Europe Ø 4.8mm 47
Swiss 48
Italy 49
46U.K. / H.K.
51
50
62
63
6-7

FC9025
EXPLODED VIEW
7-7