Piaa LP570 User manual

-1-
PKI-0035-4
LP570
InstallationInstructions
ThankyouverymuchforpurchasingPIAAproduct.
Pleasereadthisentiremanualbeforeinstallationanduseofthisproduct.
Pleasereadthecautionarypointsbeforeinstallationtoensuresafeutilizationoftheproduct.
●Thelampandtheswitchharnessareintendedforautomobileuse.Donotuseforanyotherpurpose.
●Thislampisintendedforuseinrain(dayornight),duringfoggyorsnowyconditionswherevisibilityishampered.
 Donotuseduringnormaldrivingconditions.
●Donotoperatetheswitchwhiledriving.
●Ifthelampiskeptonwhentheengineisnotrunning,itmaydrainthebattery.
●Makesurethelampisinstalledsecurelybeforedrivingthevehicle.Ifanabnormalityisfound,adjustitimmediately.
●Checkforanyloosescrewsthatholdthelampinplacebeforedriving.Ifyoufindanyloosescrewsorbolts(ifabracketis
 used),tightenthemsecurely.Ifyounoticealoosepartwhiledriving,inspectthesectionimmediatelyandmakethenecessary
 adjustments.
●AvoidrepeatedlyturningthelampoffandonasitmayreducetheoveralllifeoftheLED.
●Someofvehiclesareproducedhighvoltagesofelectricchargewhenyoustartengine.Avoidloadingextravoltagetolamps,
 pleaseturntheswitchoffwhenyoustartengine.
● Avoidneedlessdisassemblyofthelamportheswitchharnessasitmaycauseittofail.
●Ifthelampand/ortheswitchharnessisremovedandsetasideforsafekeeping,wipeawayalldustorgrimeandstoreinan
placefreeofmoisture.
●Ifthelensiscrackedordamagedinanyway,verifywhetherthereisanydamagetotheharnessortheswitchharnessthatitis
 connectedto.Ifthereisanydamagetothecordcovering,replaceitimmediately.
●Avoidinjurywhenreplacingtheharnessandtheswitchharness.Pleasedisposeofitasanon-combustibleitem.
※ The  and  marksindicatedinthismanualare
 cautionarypointsrelatedtotheinstallationoftheproduct.
 Toensuresafeandsecureinstallationoftheproduct,pleasefollowthesepointsclosely.
 Touser … Pleasekeepthismanualandareceiptwhichcanberecognizedthe
   shopnameyouboughtat.
   Whengivingthisproducttoathirdparty,alwaysincludethismanual
   togetherwiththeproduct.
 Toshopownersinstallingtheproduct … Afterinstallationoftheproduct,makesurethecustomerisprovided
   withthisowner'smanual.
●Thelampbecomesveryhotwhenturnedon.Whenparkingyourcarnearflammableitemssuchasdriedleaves,turnoffthe
 lampasitmaycauseafire.
●Donotlookdirectlyintothelightforlongperiods.Doingsomaycauseeyeirritationorvisualimpairment.

-2-
PKI-0035-4
●Inorderforthelamptoperformatitsfullpotential,userelayharnessesmanufacturedbyPIAA.
●Allworkproceduresshouldbecarriedoutinalocationwithadequatespace.Placetheshiftleverinneutralorintheparking
 position.Turnofftheengineandsetthesidebrake.
●Makesuretheenginecompartmentisadequatelycoolbeforestartingwork.Donotbeginworkifenginepartssuchasradiator,
 oil-coolerorturbopartarestillhot.
●Donotaddadditionalholestothemainbodyofthelamp.Also,donotapplyadhesivesorstickerstothelampparts.
●Donotmodifythelampharnessortheswitchharnessinanyway.Suchmodificationsmaycauseittooverheatorshort.Insome
 cases,itmaycausethevehicletocatchfire.PIAAwillnotbeliablefordamagecausedbysuchmodifications.
●Whenremovingthebatteryterminals,donottouchthe(-)and(+)terminalssimultaneously.Anelectricalshockmayoccur.
 Wearrubbergloveswhencarryingoutsuchworkprocedures.
●Makesurethe(-)and(+)terminalsdonotmakecontactwithmetal.Itcanbeextremelydangerousifashortoccurs.
●Makesureallboltsaretightlysecure.Ifthereareanylooseboltstightenthemaccordingly.
●Afterinstallingthelamp,adjustthelampsothebeamshinesatleast40minfrontofthevehicle.Also,adjustthelampalittle
 towardtheleftsothatitdoesnotshinedirectlyintotheeyesoftheopposingdriverofavehicle.(astrafficlawsstipulate-
 refertop.6foradjustmentprocedures)
●Afterinstallingthelamp,makesuretheheadlamps,wipersandhornareworkingnormally.
●Whenthebatteryterminalisremoved,memoryrelatedtotheclock,radio,audiosystemetc,willbeaffected.Afterallwork
 proceduresarecompleted,resettotheoriginalsettings.(Foradjustmentproceduresrefertoyourcar'sinstructionmanual)
Pleasereadtheinstallationproceduresthoroughlybeforehand.
●Beforeyoubeginalwaysremovethe(-)and(+)terminals.
 Alwaysremovethe(-)terminalfirstandmakesureashortdoesnotoccur.
●Whenremovingthebatteryterminals,alwaysturnthekeytoOFFandremoveit.Turnallotherelectricalunitsoffsuchas
 thelightswitch.
●Whenremovingthebatteryterminals,ifacord(foranelectricalunit)isconnected,windalengthofvinyltapearoundthe
 (-)and(+)terminalstoclearlyidentifythem.
●Verifythe(+)terminal(white)andearth(black)beforeconnecting.
●Donotobtain(+)voltagefromthealternator.
●Obtainthe(+)currentnecessaryfortheswitchfromthe(+)currentusedforthelightswitch.
 (Donotusethesamecurrentusedforacomputer,radiooraudiosystem)
●Installtheswitchharnessinapositionwhereitwillnotmakecontactwithhightemperaturesurfacessuchastheengine,
 radiatororenginecompartment.
●Arrangetheswitchharnesssothatitdoesnotmakecontactwithmovingparts.
●Donotplacetheswitchharnessonhigh-voltagewiressuchasbrakeorair-conditioningwires.
●Iftheswitchharnessmakescontactwithapartoftheengine,applyalengthofordinarycushionedtapearoundtheharness.
●Whenconnectingtheconnector,insertuntilyouhearanaudibleclick
●Whenremovingtheconnector,holdthemainbodyoftheconnectorandpullitout.Ifexcessforceisusedtopullthecord,it
 maydamagetheconnection,whichcouldcauseittooverheat.
●Makesuretheharnessdoesnotsag.Useaharnessbandofvinyltapetosecureitinplacetowiringinsidetheenginecompartment.
●Beforeconnectingittothebattery,verifythewiringarrangement.
●Whenconnectingthebatteryterminalandorotherelectricalunits,donotmistakethe(-)and(+)terminals.Alwaysstartwith
 the(+)terminal.
●Afterallwiringiscomplete,confirmthatitworksproperly.Ifitfailstoactivate,referto【4】Troubleshootingsection
 ofthismanual.
●Whendoingwiringwork,strictlyfollowthecautionarypointsmentionedbelow.Incorrectorfaultywiringmaycausethelamp
 tooperateimproperly.Insomecases,itmaycausethevehicletocatchfire.
CautionRegardingWiring/Pleasereadthoroughly

-3-
PKI-0035-4
※ Verifyallthepartsareincluded.Ifapartismissing,pleasecontactyourlocaldistributor.
ProductDetails
① Lampmainunit(2units)
⑤ One-touchconnector
(1pc)
⑥ Wiretie(5pcs)
④Hexagonalwrench(1pc)
● DonotuseanImpactwrenchwhenmountingthelamp.
● Overtorqueingthemountingnutonthebasecouldcausebase
failureandvoidthewarranty.
● Youmustutilizethewasher,lockwasher,andrubberbase.
● Torquespecificationsonthebasemountingnutis20ft/lbs(27N/m)
Impactwrench
20ft/lbs(27N/m)
※Pleaseusethetoolsindicatedbelow.
● Phillips
 headdriver
●Tape ●Pliers
ToolsRequired
●19mmwrench
③ Switch
(1pc)
② Pre-assembledrelayharness
withfuse【LR-39】（1set）
⑧ Rubbercap
(2pcs)
⑨Dummyconnector
(1pc)
⑦Double-sticktape
 forswitch (1pc)

-4-
PKI-0035-4
● Whenusingacommerciallysuppliedlampbracket,beforeremovingtheboltthatisalready
installedonthecarbody,makesurethatitissafetodoso.
● Thelampshouldbemountedinanareasufficienttosupportitssizeandweight.
Failuretodosomayresultinexcessvibrationleadingtoshorterbulblifeandorphysical
damagetothelamporyourvehicle.
● Donotattempttoinstallthelampdirectlytoanyplasticpartofthecarbody.
Ifthelampneedstobeinstalledontheplasticreinforcementmaterialsshouldbeplacedon
bothsidesoftheplasticpart.
● Wheninstalling,makesurethelampbody,lensandrimarenottouchingthebumperand
otherplasticparts.Suchplasticpartsmightdeform.
● Thelampinstallationsurfaceshouldbeflat.
● Thelampshouldbetightenedtothedegreethatthelampbodycannotbemovedbyhand.
● Thelampsaredesignedtobemountedupright.Itisveryimportantthatyoumakesurethat
 thePIAAetchedinthelensreadsrightsideup.
Forlampinstallation,aholewithadiameter
of12mmisrequired.Makenecessarypreparation
suchasinstallationoflampbracket.
Flatwasher
Nut
【1】Lampinstallation
Tighteningtorque：
20ft/lbs(27N/m)
Springwasher
Rubbercushion
Flatwasher
Nut
Springwasher
Rubbercushion

-5-
PKI-0035-4
【2】RelayHarnessInstallationSequence
Thenumbersshowninthefigurebelowindicatethesequencethepartsshouldbeinstalled.
Removethe(-)terminalfromthe
battery.
Removethe(+)terminalfromthe
battery.
Bringtherelayconnectorintothe
interiorofthevehicleandconnect
totheswitch’sconnector.
Takethe(+)cord(white)andusingthe
one-touchconnector,tieittogethertothe
vehicle’s(+)cord.
Ifonly1lampwillbeinstalled,sealtheunusedconnector
withtheRubbercapandDummyconnectorincludedinkit.
Connectthelampharness
totheconnector.
Firstgroundtheterminal
thentakethe(-)cord
(black)andconnectitto
the(-)terminal.
Takethe(+)terminal
cord(white)andattach
ittothe(+)terminaland
connecttothebattery.
Attachthe(-)
terminaltothe
battery.
Afterlamphasbeeninstalled,verifytherelay
harnessdoesnotmakecontactwiththe
engine’smovingpartsorsectionsthatemit
extremeheat.Usethewiretieincludedand
securetoharnessesinsideenginecompartment.
Harness
Wiretie
※ Useapairofplierstoverifytheone-touch
connectorissecure.
Switch
Relay
Battery
Cord
One-touch
connector
(+)cord(white) (-)cord(Black)
Makesuretoproperly
securetherelayunit
usingboltsoraharness.
Theharnessmustalso
befacingdownward.
Double-sticktapeforswitch.
Placeinareathatiseasily
accessiblefromdriver’sseat.
Facingdown
(+)cord(white)
Rubbercap Dummy
connector

-6-
PKI-0035-4
Whenusingthelampforextendedperiodsoftime,werecommendthatagrillcoverbeusedoverthemain
lampunitinordertopreventunduedamage.
1
Lampmainunit
Grillcover
【3】ProceduresforInstalling/Removingthegrillcover
Forinstallingthegrillcover,firsttakethesmalltabontheupperedgeofthecoverandlineitupwiththe
slotonlampunitandsnapitinplace.Thencontinuetosnaptheremainingtabsinplace.
Forremovingthegrillcover,firsttaketheoneside-tabonthegrillcoverandliftitovertheslotonthelamp
unit,thencontinuewiththeuppertab.
●Thegrillcoverisstructurallybuiltsothatitdoesnotcomeloosewhilethevehicleisin
motion.Therefore,beextremelycarefulwhenremovingandinstallingthegrillcoveras
itisaverytightfit.
installation
slots
Theinstallationslotsarelocated
at4positionsonthelampunit;
left/rightandtop/bottom.
Theinstallationtabsarelocated
at3positionsonthegrillcover
left/rightandtop.
View of lamp unit
fromabove. Theinstallation
slotsonthelamp
unit.
Tabs
Tabs
Lamp
cover
2

-7-
PKI-0035-4
 1 Afterinstallation,ifthelampdoesnotactivate
   → Checkthewiringandmakesuretherearenofaultyorirregularconnections.
  ●Iftheswitchilluminationdoesnotlightup.
   → Verifythe(+)wirefromtheswitchisproperlyconnected.Ifitisnotcorrectlyconnectitwillnotactivate.
→
Verifythefuselocatedonthevehicle'swiringsystem.(theswitch's(+)wireshouldbeconnectedtothe
    fusebox).Ifitisburnedout,connectittoanothercircuit.
   → Iftheswitchitselfisfaulty,thesamesymptomsmayexist.Werecommendthattheentireswitchunit
    bereplaced.
   → Checkthefusefortheswitchharness.Ifitisburnedout,followinstructionsindicatedin
    [3FusereplacementProcedures].
  ●Theswitchilluminationlightsupbutwhenoperatingdoesnotwork.
   → Checktheconnecting(-)cordtothebodyearth.
   → Theremaybecaseswhereeachterminalrelatedtospecificsectionsmaybeincorrectlyconnected.
    Checkforanylosewiresandalsofordirtorgrime.
   → ChecktheswitchopelationIfanabnormalityisfound,replaceitaccordingly.
 2 IftheLEDsuddenlyfailstolightup…
   → Checkthefuselocatedonthevehicle'swiringsystem.Ifitisburnedout,replaceaccordingly.
   → Checkthefusefortheswitchharness.Ifitisburnedout,followinstructionsindicatedin
    [3FusereplacementProcedures].
   → Theremaybecaseswhereeachterminalrelatedtospecificsectionsmaybeincorrectlyconnected.
    Checkforanylosewiresandalsofordirtorgrime.
   → Checktheswitchopelationifanabnormalityisfound,replaceitaccordingly.
3 FusereplacementProcedures
→ Ashortcircuitmayhaveoccurred.Checkthewiringsystem.Ifanytypeofdamageis
    foundreplaceaccordingly.(Non-replacementmayposeapotentialdanger)(Shortcircuitsaremainly
    causedwhenwiresarecaughtintheassemblyorwhenthereisagapinthesleeveconnectedtothe
    lampharness).
Verifyeachsectionaccordingtothefollowing.
【4】Troubleshooting……
Typically,drivinglightsaremountedabovethefrontbumperabout14cm-30inchesfromthegroundtoprovide
extrahighbeamillumination.Drivinglightscanbemountedbelowthebumper,althoughtheywillnotbeaseffective
becausethelightwillhitthegroundsoonerandreducetherangeofthelight.
Visualaimismadewiththecenterofthebeamhotspot1.5inchesbelowthelampcenterat25feetwiththelamp
facingstraightforward.(seebelow.)
●Donotusedrivinglightsinto
 oncomingtraffic.
 Drivinglightsshouldneverbe
 theonlyforwardlightsource.
 Drivinglightsshouldonlybe
 usedwiththeheadlamphigh
 beams.
1.5
DRIVING ／ SpotLightAiming

-8-
PKI-0035-4
【5】PIAALIMITEDWARRANTY
Withtheexceptionofbulbs,PIAACorporation,USA("PIAA")warrantsitsproductstobefreefrom
defectsinworkmanshipandmaterialsundernormaluseforaslongastheoriginalpurchaserownsthem.
 EXCLUSIONS
ThisLimitedWarrantyspecificallyexcludesdefectsresultingfrommisuse,abuse,neglect,alteration,
modification,improperinstallation,unauthorizedrepairs,submersion,theft,vehiclecrash,orbyany
othertypeofimpact.ExceptfortheLimitedWarrantystatedabove,therearenowarrantiesofPIAA
productsoranypartthereof,whetherexpressorimplied.Anyimpliedwarrantyofmerchantability
oranywarrantyoffitnessforaparticularpurposeisexpresslydisclaimed.Somestatesdonot
permitthedisclaimerofimpliedwarranties.
 LENSCRACKS
Crashorimpactdamageisnotcovered.Thiscanbedeterminedbyachiporscrapeonthelensorthe
housing.Stresscrackssometimesoccurwhenthelensissubjectedtosuddenandextremetemperature
changes.Astresscrackhasnochiporothersignofimpact.Stresscracksarecoveredunderwarranty.
 EXCLUSIONOFDAMAGES
InnoeventshallPIAAbeliableforanydamageswhatsoever(including,withoutlimitation,consequential
damages,incidentaldamages,ordamagesforlossofuse,lossofbusinessprofits,businessinterruption,
lossofbusinessinformation,lossoftime,inconvenience,orotherlosses)arisingoutoftheuse,misuse,
orinabilitytouseaPIAAproduct.PIAAreservestherighttochangethedesignitsproductswithoutany
obligationtomodifyanypreviousproduct.Thiswarrantygivesyouspecificlegalrights.Youmayalso
haveotherrightsthatvaryfromstatetostate.
 REPAIRANDREPLACEMENT
IfaPIAAproductissuspectedofbeingdefective,itmustbesubmittedfreightprepaid,toeitheran
authorizeddealerordistributorforwarrantyinspection.Thereceiptorotherproofofpurchaseanda
descriptionoftheproblemmustbeincluded.Thereturnedproductwillbeinspected.Iftheproductis
foundtobedefectiveandcoveredbythisLimitedWarranty,thesoleremedyisrepairorreplacement,at
PIAA'soption.Arepairedorreplacementproductwillbeshippedbackatnocharge,andwillbewarranted
tobefreefromdefectsinworkmanshipandmaterialsundernormaluseforaslongastheoriginal
purchaserownsit.Removal,installation,orreinstallationcostsarenotcoveredbythisLimitedWarranty.
PIAA CORPORATION
www.piaa.com
www.piaa.co.jp