Pickering 45-720A User manual

pickeringtest.com
Issue 4.4 August 2021
45-720A User Manual
PXI 6 U Expandable 250 MHz 16x16 RF Matrix

Page (II) 16 x 16 RF MATRIX MODULE 45-720A
pickering
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2021) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
16 x 16 RF MATRIX MODULE 45-720A
pickering
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV) 16 x 16 RF MATRIX MODULE 45-720A
pickering
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy reference should be made to the safety instructions for
provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
16 x 16 RF MATRIX MODULE 45-720A
pickering
Copyright Statement ...................................................................II
Technical Support and Warranty................................................III
Product Safety .............................................................................IV
Contents (this page)....................................................................V
Warnings and Cautions ..............................................................VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Functional Description..........................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks...........................................................3.1
Hardware Installation ............................................................3.2
Software Installation .............................................................3.2
Testing Operation ..................................................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options For Pickering PXI Modules ............4.1
Module Architecture 45-720A .............................................4.2
Sub-Unit Tables ....................................................................4.4
Programming The Module 45-720A ....................................4.7
Section 5
Connector Information................................................................5.1
Section 6
Trouble Shooting.........................................................................6.1
Section 7
Maintenance Information............................................................7.1
Relay Lookup Tables 45-720A .............................................7.1
Component Layout 45-720A.................................................7.5
CONTENTS

Page (VI) 16 x 16 RF MATRIX MODULE 45-720A
pickering
THIS PAGE INTENTIONALLY BLANK

Page (VII)
16 x 16 RF MATRIX MODULE 45-720A
pickering
Page (VII)
REED RELAY MODULE 40-110/115/120/125
pickering
WARNINGS AND CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This module may contain hazardous voltages. Before removing the module from the rack remove all
supplies and disconnect user I/O signals.
Unused slots in the host chassis are populated with blanking plates to prevent access to user
I/O signals that may be present. Blanking panels are available to order from Pickering in a variety
of slot widths. If the product is not used in this manner for example by using an extender card then
additional care must be taken to avoid contact with exposed signals.
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4.
anti-static bags.
CAUTION - PRODUCT DOCUMENTATION SYMBOL
and understood before attempting to install or operate the product.
!
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O
signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.

Page (VIII) 16 x 16 RF MATRIX MODULE 45-720A
pickering
THIS PAGE INTENTIONALLY BLANK

Page 1.1
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
pickeringtest.com
PXI 6 U Expandable 250 MHz 16x16 RF Matrix 45-720A
ISSUE 7.1 APR 2020
y16x16 Coaxial Matrix
y250 MHz Bandwidth
yHigh Quality Ruthenium Reed Relays
yChoice of Front Panel Mounted Coaxial Connectors
yAvailable in 50 Ω and 75 Ω Versions
yUses High Reliability Reed Relays
yVISA/IVI Drivers Supplied for Windows
y3 Year Warranty
The 45-720A module is a 6 U 16x16 RF Matrix suitable for
switching frequencies beyond 250 MHz. It is available in
50 Ω and 75 Ω versions with a choice of coaxial connectors.
It is intended for the easy construction of high performance
bi-directional matrix switching systems.
Automatic isolation switches are located on all input and
output connections. These are used to disconnect unused
signals from the external test fixture to maximize isolation
and RF performance.
Typical applications are switching signals to high speed
digitizers. The matrix is constructed using high reliability
ruthenium electro-plated reed relays, with an operational
life of >108 to give maximum switching confidence with long
service and stable contact resistance.
Matrix Operation
The 45-720A is a true 16x16 high density
matrix, any combination of cross-points
may be selected. Only the signal is
switched, all grounds are common. Loop-
thru is included on X signals.
Easy Expansion with Automatic Loop-Thru
All unused X input channels are
automatically switched to the
corresponding “Loop-thru” output
connection. This allows for simple
expansion (with a little performance loss)
and permits the user to place matched
terminations on the outputs if required.
Switching Diagram for the 45-720A
16x16 Matrix Module
IN
OUT
X1
IN
OUT
X2
IN
OUT
X3
IN
OUT
X4
IN
OUT
X5
IN
OUT
Y6
IN
OUT
Y7
IN
OUT
X8
IN
OUT
X9
IN
OUT
X10
IN
OUT
X11
IN
OUT
X12
IN
OUT
X13
IN
OUT
X14
IN
OUT
X15
IN
OUT
X16
IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN
Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16
Isolation Switch
Crosspoint
Changeover

Page 1.2 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Overview
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN
X1
X2
X3
X4
X5
X6
X7
X8
X9
X10
X11
X12
X13
X14
X15
X16
Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16
MATRIX 1
XOUT
XIN
16
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN
XOUT
MATRIX 2
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN
MATRIX 6
XIN
16
X1
X2
X3
X4
X5
X6
X7
X8
X9
X10
X11
X12
X13
X14
X15
X16
Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16
X1
X2
X3
X4
X5
X6
X7
X8
X9
X10
X11
X12
X13
X14
X15
X16
Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16
Matrix Expansion
Larger matrices may be constructed by daisy-chaining the X signals from multiple modules, for example, six modules form a 96x16
matrix (1536 crosspoints). Expansion is achieved by interconnecting Xout (Loop-thru) of one matrix to Xin of the next using coaxial
cables as shown below. It should be noted that the operating bandwidth will reduce slightly as the number of modules is increased.
Diagram Showing How Multiple 16x16
Matrix Modules Can be Daisy-Chained to
Form a Larger Matrix

Page 1.3
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Specifications
Typical Insertion Loss For One Module
Typical VSWR with Loop-Through For One Module
Typical VSWR For One Module
Typical Insertion Loss for 2 Daisy-Chained Modules
Typical Insertion Loss with Loop-Through For One Module
Typical VSWR for 2 Daisy-Chained Modules

Page 1.4 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Specifications
Switching Specification
Switch Type: Ruthenium Reed
Maximum Voltage: 100 VDC
Maximum Power:
Maximum Switch Current:
Maximum Carry Current:
10 W
0.5 A
0.5 A
On Path Resistance:
Off Path Resistance:
DifferentialThermal Offset:
<750 mΩ
>108 Ω
<30 µV
Charateristic Impedance: 50 Ω or 75 Ω
Operate Time:
Release Time:
<3.0 ms
<3.0 ms
Expected Life, low power load:
Expected Life, full power load:
>1x108 operations
>5x106 operations
RF Specification (50 Ω)
Maximum Frequency:
Typical Rise Time:
Insertion Loss (<250 MHz):
VSWR (<250 MHz):
Isolation (<250 MHz):
Crosstalk (<250 MHz):
250 MHz
800 ps †
<3.5 dB †
<1:1.9 †
>70 dB
>60 dB
Loop Through RF Specification (1 Pole)
Insertion Loss (<250 MHz):
VSWR (<100 MHz):
<0.5 dB
<1:1.05
RF Specification (6 modules daisy-chained)
Maximum Frequency:
Typical Rise Time:
Insertion Loss (<250 MHz):
VSWR (<250 MHz):
Isolation (<250 MHz):
Crosstalk (<250 MHz):
250 MHz
800 ps †
<3.5 dB †
<1:1.9 †
>70 dB
>60 dB
† Matrix RF Performance is entirely dependant upon the
combination of cross-points currently selected, these
figures are for one selected cross-point on any X or Y
channel only, refer to graphs.
Power Requirements
+3.3 V +5 V +12 V -12 V
0 1 A (0.6 A typical) 0 0
Operating/Storage Conditions
Operating Conditions
Operating Temperature:
Humidity:
Altitude:
0 °C to +55 °C
Up to 95 % non-condensing
5000 m
Storage and Transport Conditions
Storage Temperature:
Humidity:
Altitude:
-20 °C to +75 °C
Up to 95 % non-condensing
15000 m
PXI & CompactPCI Compliance
The module is compliant with the PXI Specification
2.2. Local Bus, Trigger Bus and Star Trigger are not
implemented.
Uses a 33 MHz 32-bit backplane interface.
Safety & CE Compliance
All modules are fully CE compliant and meet applicable
EU directives: Low-voltage safety EN61010-1:2010,
EMC Immunity EN61326-1:2013,
Emissions EN55011:2009+A1:2010.
Mechanical Characteristics
6 U PXI (CompactPCI) module:
• 45-720A-511 - single slot
• 45-720A-541 - dual slot
• 45-720A-711 - dual slot
• 45-720A-741 - single slot
• 45-720A-751 - single slot
3D models for all versions in a variety of popular file
formats are available on request.
Chassis Compatibility
Pickering 6 U PXI modules will operate in any 6 U PXI
chassis, in addition they will also operate (with 100 %
compatibillity) in any 6 U CompactPCI chassis.
Connectors
PXI bus via 32-bit P1/J1 backplane connector.
Front panel signal connectors:
• 45-720A-511 - coaxial 50 Ω SMB
• 45-720A-541 - coaxial 50 Ω Lemo 00
• 45-720A-711 - coaxial 75 Ω BT Type 43/SMZ
• 45-720A-741 - coaxial 75 Ω 1.0/2.3
• 45-720A-751 - coaxial 75 Ω Mini SMB

Page 1.5
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Ordering Information
Product Order Codes
PXI 6 U Expandable 16x16 RF Matrix:
50 Ω SMB, single slot module
50 Ω Lemo 00, dual slot module
75 Ω BT Type 43/SMZ, dual slot module
75 Ω 1.0/2.3, single slot module
75 Ω Mini SMB, single slot module
45-720A-511
45-720A-541
45-720A-711
45-720A-741
45-720A-751
Product Customization
Pickering modules are designed and manufactured on our
own flexible manufacturing lines, giving complete product
control and enabling simple customization to meet very
specific requirements.
Customization can include:
• Alternative relay types
• Mixture of relay types
• Alternative number of relays
• Different performance specifications
All customized products are given a unique part number,
fully documented and may be ordered at any time in the
future. Please contact your local sales office to discuss.
Mating Connectors & Cabling
For connection accessories for the 45-720A module range,
please refer to the 90-011D RF Cable Assemblies data
sheet where a complete list and documentation can be
found for accessories, or refer to the Connection Solutions
catalog.

Page 1.6 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Supporting Products & Software
We also offer customized cabling and have a free online Cable Design Tool
that can be used to create custom cable solutions for many applications.
Visit: pickeringtest.com/cdt to start your design.
Mass Interconnect
We recommend the use of a mass interconnect solution when an
Interchangeable Test Adapter (ITA) is required for a PXI or LXI based
test system. Our modules are fully supported by both Virginia Panel and
MacPanel.
Pickering Reed Relays
We are the only switch provider with in-house reed relay manufacturing
capability via our Relay Division. These instrument grade reed relays
feature SoftCenter™ technology, ensuring long service life and repeatable
contact performance.
To learn more, please go to: pickeringrelay.com
Connectivity Solutions
We provide a full range of supporting cable and connector solutions for all our switching products—20 connector families
with 1200+ products. We offer everything from simple mating connectors to complex cables assemblies and terminal
blocks. All assemblies are manufactured by Pickering and are guaranteed to mechanically and electrically mate to our
modules.
Connectors & Backshells Multiway Cable Assemblies RF Cable Assemblies Connector Blocks
Programming
Pickering provide kernel, IVI and VISA (NI & Keysight) drivers which are compatible with all Microsoft supported versions of
Windows and popular older versions. For a list of all supporting operating systems, please see: pickeringtest.com/os
The VISA driver is also compatible with Real-Time Operating Systems such as LabVIEW RT. For other RTOS support contact
Pickering. These drivers may be used with a variety of programming environments and applications including:
• Pickering Interfaces Switch Path Manager
• National Instruments products (LabVIEW, LabWindows/CVI, Switch Executive, MAX, TestStand, VeriStand, etc.)
• Microsoft Visual Studio products (Visual Basic, Visual C+)
• Keysight VEE and OpenTAP
• Mathworks Matlab
• Marvin ATEasy
• MTQ Testsolutions Tecap Test & Measurement Suite
Drivers for popular Linux distributions are available, other environments are also supported, please contact Pickering with
specific enquiries.
We provide Soft Front Panels (SFPs) for our products for familiarity and manual control, as well as comprehensive
documentation and example programs to help you develop test routines with ease.
To learn more about software drivers and development environments, please go to: pickeringtest.com/software

Page 1.7
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 1 - TECHNICAL SPECIFICATION
6 U 250 MHz 16x16 RF Matrix, 45-720A
pickeringtest.com
Supporting Products & Software
© Copyright (2021) Pickering Interfaces. All Rights Reserved Pickering Interfaces maintains a commitment to continuous product development, consequently we reserve the right to vary from the description given in this data sheet.
Signal Routing Software
Our signal routing software, Switch Path Manager, automatically selects and energizes
switch paths through Pickering switching systems. Signal routing is performed by simply
defining test system endpoints to be connected together, greatly accelerating Test System
software development.
To learn more, please go to: pickeringtest.com/spm
Diagnostic Relay Test Tools
eBIRST Switching System Test Tools are designed specifically for our PXI, PCI
or LXI products, these tools simplify switching system fault-finding by quickly
testing the system and graphically identifying the faulty relay.
To learn more, please go to: pickeringtest.com/ebirst
Three Year Warranty & Guaranteed Long-Term Support
All standard products manufactured by Pickering Interfaces are warranted against defective materials and workmanship
for a period of three years from the date of delivery to the original purchaser. Extended warranty and service agreements
are available for all our modules and systems with various levels to suit your requirements. Although we offer a 3-year
warranty as standard, we also include guaranteed long-term support—with a history of supporting our products for typically
15-20 years. To learn more, please go to: pickeringtest.com/support
Available Product Resources
We have a large library of product resources including success stories, product and support videos, articles and white
papers as well as application specific product brochures to assist when looking for the switching, simulation and connection
solutions you need. We have also published handy reference books on Switching Technology and for the PXI and LXI
standards.
To view, download or request any of our product resources, please visit: pickeringtest.com/resources

Page 1.8 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 1 - TECHNICAL SPECIFICATION
THIS PAGE INTENTIONALLY BLANK

Page 2.1
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 2 - TECHNICAL DESCRIPTION
SECTION 2 - TECHNICAL DESCRIPTION
FUNCTIONAL DESCRIPTION
A functional block diagram is provided in Figure 2.1. The Matrix Module is powered by +5V inputs via Compact PCI
connector J1. The interface to the user test equipment is via the front panel mounted RF connectors. The module
comprises a PCB populated with RF relays. The relays are energised via control signals from relay drivers U8
to U31. Each relay driver is addressed by PCI bridge U1, via the control logic comprising U3 to U6, to output the
required signal. Module conguration is determined by data stored in EEPROM U7. PCI Bridge U1 is congured by
EEPROM U2.
Figure 2.1 - 16 x 16 RF Matrix Module 45-720A: Functional Block Diagram
FRONT
PANEL
CONNECTORS
RELAY
DRIVERS
U8
TO
U31
MODULE
CONFIGURATION
U7
PCI
BRIDGE
U1
PCI BRIDGE
CONFIGURATION
U2
TERMINATING
RESISTORS
R3 TO R14
COMPACT PCI
BUS
CONNECTOR
J1
+5V
0V
RELAY COILS
RELAY CONTACTS
CONTROL
LOGIC
U3, U4,
U5, U6

Page 2.2 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 2 - TECHNICAL DESCRIPTION
Y ISOLATION RELAYS (X1 TO X8)
X ISOLATION RELAYS
Y1 TO Y4
TO ‘X’ CONNECTIONS TO ‘X’ CONNECTIONS
TO ‘X’ CONNECTIONS TO ‘X’ CONNECTIONS
TO ‘X’ CONNECTIONS TO ‘X’ CONNECTIONS
TO ‘X’ CONNECTIONS TO ‘X’ CONNECTIONS
X ISOLATION RELAYS
Y5 TO Y8
X ISOLATION RELAYS
Y9 TO 12
X ISOLATION RELAYS
Y13 TO Y16
FROM MATRIX ‘X’ ISOLATION RELAYS BELOW
Y ISOLATION RELAYS (X9 TO X16)
CROSSPOINT
X1
X1-LT
X2
X2-LT
X3
X3-LT
X4
X4-LT
X5
X5-LT
X6
X6-LT
X7
X7-LT
X8
X8-LT
X9
X9-LT
X10
X10-LT
X11
X11-LT
X12
X12-LT
X13
X13-LT
X14
X14-LT
X15
X15-LT
X16
X16-LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
MT
LT
GLOBAL
ISOLATION
AND
LOOP THROUGH
RELAYS
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
Y9
Y10
Y11
Y12
Y13
Y14
Y15
Y16
45-720A 16x16 Matrix
Figure 2.2 - 16 x 16 RF Matrix Module 45-720A: Schematic

Page 3.1
16 x 16 RF MATRIX MODULE 45-720A
pickering SECTION 3 - INSTALLATION
Page 3.1
REED RELAY MODULE 40-110/115/120/125
pickering SECTION 3 - INSTALLATION
kg
PREOPERATION CHECKS (UNPACKING)
1. Check the module for transport damage and report any damage immediately to Pickering Interfaces.
Do not attempt to install the product if any damage is evident.
2. Position the chassis relative to any other equipment the module(s) will connect with. Ensure the chassis is not
connected to the electrical supply.
3. Ensure that the designated area for the chassis containing the module is of at and solid construction to
withstand and support the combined weight of the module(s) and chassis.
SECTION 3 - INSTALLATION
!
Refer to the Warnings and Cautions at the front of this manual
Modular products require installation in a suitable PXI/LXI chassis. The module is designed for indoor use only.
Figure 3.1 - Installing the Module into a PXI/cPCI/LXI Chassis
PXI / LXI Chassis
6U PXI/Compact PCI
Chassis
6U PXI Module
Ejector Handle
in Outward Position
Ejector Handle
in Outward Position
Figure 3.1 - Installing the module into a 6U PXI Chassis

Page 3.2 16 x 16 RF MATRIX MODULE 45-720A
pickering
SECTION 3 - INSTALLATION
SOFTWARE INSTALLATION
First install the appropriate Pickering PXI switch card drivers by running the installer program Setup.exe (provided
in a compressed zip le), either from the CD-ROM supplied, or by downloading the latest version from our website
pickeringtest.com - the recommended method. Setup is accompanied by a ReadMe le containing
additional installation information. A single installation covers all cards in the System 40, System 45 and System
50 ranges.
When installation completes, the installed drivers’ ReadMe le is offered for display. It can also be displayed
later using a shortcut on the Programs>>Pickering menu.
If you are not a LabVIEW user you should choose the “full” version, and once that has been installed run
the LabVIEW Runtime Engine installer via the shortcut on the Programs>>Pickering menu. In the absence of
LabVIEW the Runtime Engine is required to support the Pickering Test Panels application.
!
HARDWARE INSTALLATION
ELECTRICAL CONNECTION (CHASSIS)
1. The chassis must be electrically installed in accordance with local regional electrical codes by a qualied
engineer.
2. The chassis must be grounded.
Electrostatic discharge can damage the components on the module. To avoid such damage in handling the
board refer to page VII.
Ensure that there is adequate ventilation.
The module should be installed in accordance with the following procedure:
1. Ensure that the system is turned OFF but still connected to mains so that it remains grounded.
2. Choose an appropriate slot in the rack.
3. Remove the blanking plate for the chosen slot.
4. Ensure that the injector/ejector handles are in the outward position. Align the module with the card guides
on the top and bottom of the slot.
Do not move the injector/ejector handles whilst inserting the module as the module will not insert properly.
5. Hold the handles whilst slowly sliding the module into the card guides until the handles catch on the injector/
ejector rails (refer to Figure 3.1).
6. Simultaneously move both injector/ejector handles to the inward position until the module rmly seats into the
backplane. The front panel of the module should be ush with the front panel of the chassis.
7. Secure the front panel of the module using both screws to the chassis front panel mounting rails.
8. In a system employing a remote control interface to connect an external controller to a PXI chassis or to link
multiple chassis, power-up the system as follows:
a. For a system comprising an external controller and one chassis, power up the chassis before powering up
the external controller.
b. For a system comprising more than one chassis, turn ON the last chassis in the system followed by the
penultimate, etc, and nally turn ON the external controller or chassis containing the system controller.
9. For Pickering Interfaces modular LXI installation there is no requirement to use any particular power up
sequence.