Pinnacle Technology KP7MX Assembly instructions

KP7MX PRINTER
DRIVER INSTALLATION
INSTRUCTION
Pinnacle Technology Corp.

CONTENTS
1USB/SERIAL PRINTER DRIVER INSTALLATION ...................................................................................... 1
1.1 Printer Driver Installation .................................................................................................................. 1
1.1.1 Serial /Parallel Printer Driver Installation.................................................................................. 3
1.1.2 USB Printer Driver Installation ................................................................................................. 6
1.1.3 Ethernet/WIFI Printer Driver Installation .................................................................................. 8
1.2 How to Know the Connecting Port.................................................................................................. 10
1.3 How to Configure Port..................................................................................................................... 13
2WIRELESS 2.4G / WIRELESS 433 PRINTER (KP7XW4/KP7XW2).......................................................... 19
2.1 Printer Driver Installation ................................................................................................................ 19
2.2 Wireless 433MHz Base Station ....................................................................................................... 23
2.3 Wireless 433 USB Dongle/2.4G ...................................................................................................... 25
2.3.1 USB Dongle Driver Installation............................................................................................... 25
2.3.2 How to Know the Connecting Port.......................................................................................... 28
2.3.3 Dongle Parameter Setting ........................................................................................................ 29
2.4 How to Configure Port..................................................................................................................... 30

1
1USB/SERIAL PRINTER DRIVER INSTALLATION
1.1 Printer Driver Installation
Connect the KP7X to PC, run the attached CD-disk and double click the file ‘Aclas
printer.exe’in the folder ‘Aclas Printer’ to install the printer driver.
Click”Next”
Click “Next”
Click “Browse”to choose
the destination location.

2
Click “Install”
Here shows the
install destination
location

3
1.1.1 Serial /Parallel Printer Driver Installation
Choose “COM/LPT”
If the printer is serial printer, the
user must click “Setting”to
config the connect ports.
Choose the right connect
port from the drop-down
list.

4
Click “OK”.
Choose “Hardware”
Click “Install”

5
Click “Finish”to finish
Serial/parallel printer driver
installation.

6
1.1.2 USB Printer Driver Installation
Choose “USB”
Choose the USB port from the
drop-down list and click
“Install”

7
Click “finish”to finish USB
printer driver installation.

8
1.1.3 Ethernet/WIFI Printer Driver Installation
Choose “TCP”
Input IP address. The
default port is 9100.

9
Note:
After installing the printer driver, you can use the printer. If the printer could not work,
you can refer to Chapter 1.2 to see the connecting port and make sure that the connecting
port you choose is correct and is not being used; then refer to Chapter 1.3 to configure
port.
Click “Finish”to finish
Ethernet/WIFI printer
driver installation.

10
1.2 How to Know the Connecting Port
Connect the KP7X to the computer, follow steps below to know which port is connected.
Right click ‘My Computer’ icon on the desktop, and choose ‘Manage’:
Right click the ‘My
Computer’icon and then
choose ‘Manage’.
Click ‘Device
Manager’
Then click ‘Port
(COM&LPT)’

11
Serial printer connect port:
Parallel printer connect port:
此处显示串口打印
机的连接端口
Here you can see the
connecting port of
serial printer.
Here you can see the
connecting port of
parallel printer.

12
USB printer connect port:
Here you can see the
connecting port of
USB printer.

13
1.3 How to Configure Port
Step1: Enter ‘properties’interface of the printer first to configure port
after knowing the connecting port.
If your PC is installed with Windows XP system, please follow the below steps to enter
‘properties’interface.
Click ‘Printers and
Faxes’in start menu.
Right click the printer icon, and
choose the item ‘Properties’.

14
If your PC is installed with Vista system, please follow the below steps to enter ‘properties’
interface.
Click ‘Printers’after
choosing ‘Settings’in
start menu.
Click this item.
Choose the item
‘Properties’.

15
Note: If you are not allowed to access to run as the administrator, please choose the item
‘properties’directly after entering the Printer interface, as the window below:
If your PC is installed with WIN7 system, please follow the below steps to enter ‘properties’
interface.
Right click the printer
icon, and then choose the
item ‘Properties’.
Click “Devices
and Printers”in
start menu.

16
Right click “Aclas Printer”,
choose “Printer properties ”.

17
Step 2: Choose connecting port
Choose the connecting port that you have known from Chapter 1.2. For example, the connecting
port of the USB printer known from Chapter 1.2 is COM3, so you should choose COM3 in the
following interface. Take the port configuration of USB printer in Windows XP system as an
example:
Step 3: configure port
Note: Parallel printers and USB could skip this step, and go to step 4 directly.
Choose this
item.
Select the
connecting port.
Click
it.
Click it

18
Step 4: finish port configuration
Click “OK”.
Choose “Hardware”
Choose the item
‘General’
Click it to print test page, and
then click ‘OK’.