Double Cylinder Deadbolt
Step 1: Preparation
Cut template on line (A) & fold on line
(B) as shown. Place on door at your
preferred height and mark both the latch
height (C) and centre of handle hole (D)
with a pencil. Remove template, and
measure the thickness of door to mark
the centre point of the door edge. Use
a 25mm spade bit to drill an accurate
hole through the door edge, and using a
hole saw, drill a 54mm hole through the
door front.
Accuracy is vital so mark and measure
carefully and drill holes level.
Instructions to install the Deadbolt.
If installing this deadbolt into a new door you will need the following tools - 25mm spade bit, 2mm drill bit, 54mm hole saw, corded or cordless drill, hammer, wood chisel, Phillips
head screwdriver, tape and pencil. If you are replacing an existing deadbolt you shouldn’t require the drill, hole saw or spade bit as it will replace most standard dead bolts.
Very Important!
Please fasten all screws by hand and not an electric screw driver or drill, as over tightening is not recommended.
Step 3: Attaching the cylinders to door.
Fit outside cylinder (without screws) onto the door whilst positioning the spindle horizontally, passing through
cam in latch. Attach internal cylinder with spindle vertically onto door. Align screws and tighten rmly.
How to convert Deadbolt Latch from 60mm to 70mm
Twist anti-clockwise and pull the latch outwards. Twist clockwise until
the tab clicks in place at the 70mm square marking.
Exterior
deadbolt
Interior
deadbolt
Line B
Line A
C
D
60mm
(or 70mm)
Tip: This spindle must
remain horizontal
Tip: This spindle must
remain vertical
Twist, pull and
twist from 60mm
to 70mm
WARRANTY CONDITIONS
Any claim under this warranty must be made within 3 years of the date of purchase of the product. To make a claim under this warranty, take the product (with proof of purchase) to any Bunnings store (see www.bunnings.com.au for
store locations). Pinnacle Hardware bears reasonable, direct expenses of claiming under the warranty. You may submit details and proof of purchase to our support center for consideration. The warranty covers manufacturer defects in
materials, workmanship and nish under normal use. This warranty is provided in addition to other rights and remedies you may have under law: Our goods come with guarantees that cannot be excluded under the Australian consumer
law or Consumer Guarantees Act 1993 (NZ). You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty excludes damage resulting from product misuse or product neglect. The warranty covers domestic use only and does not apply
to
commercial
applications.
This
warranty
is
given
by
Pinnacle
Hardware,
ABN
87
614
496
196,
28
Hudson
Court,
Keysborough
Vic
3173,
1800
349
776,
Email:
[email protected].
New
Zealand
customers
please
contact
HARCO
(Harkness
&
Y
oung
Ltd),
09
27
64071,
Email:
[email protected].
‘Pinnacle’
is
a
trademark.
©
Pinnacle
Hardware.
Suitable
for
model
number
0123360.
Step 2: Installing the Latch
Place Latch (F) into the 25mm hole
on the side of the door and mark the
door around the square plate with
a pencil. Using a hammer and a
chisel, check out the timber so that
the latch ts into the newly created
recess and nishes ush with the
door. Once completed push latch
into place and drill 2mm pilot holes
into the door edge, then simply
screw the Timber Screws (G) into
place. Ensure the arrow on deadbolt
is facing upwards direction.
