Pioneer Eclipse SwingStar SS1715V User manual

Operator’s Manual
Floor Machines
®
SS1715V
17” SwingStar
1.5hp motor, 175 rpm
SS2015V
20” SwingStar
1.5hp motor, 175 rpm
SS2015DV
20” SwingStar
1.5hp motor, 175/320 rpm

1) Machine must be registered at the time of purchase on a form provided by Pioneer Eclipse
Corporation. Your Pioneer Eclipse Distributor is responsible for the registration of your machine.
Please cooperate with your distributor in supplying necessary information on the card.
2) The machine must have been purchased from Pioneer Eclipse or an authorized Pioneer Eclipse
Distributor.
3) This warranty extends to the original purchaser only and is not transferable to subsequent owners.
TIME PERIODS
ONE (1) YEAR PARTS AND LABOR - Warranted for the forementioned time periods to be free from
defects in material and workmanship from the date of purchase by the original owners. (See Exclusions.)
EXCLUSIONS (Not Covered by Warranty)
1) Parts that fail through normal wear by reason of their characteristics (pads, brushes, belts, bumpers,
skirting, or other consumable parts).
2) This warranty does not extend to parts affected by misuse, neglect, abuse or improper maintenance.
All defective parts must be returned to the Distributor for credit.
3) Electric motors warranted by motor manufacturer.
THE OBLIGATION OF PIONEER ECLIPSE CORPORATION
1) The obligation of Pioneer Eclipse under this warranty is limited to repairing or replacing, at its option,
any part which is proven to be defective in material or workmanship under normal use for the
applicable period stated above.
2) Warranty repairs will be made by your Pioneer Eclipse Distributor without charge for parts and labor.
3) Parts repaired or replaced under this warranty are warranted only during the balance of the original
warranty period. All defective parts replaced under these warranties become the property of Pioneer
Eclipse.
WARRANTY SERVICE
To obtain warranty service, take your machine and proof of purchase to any authorized Pioneer Eclipse
Distributor, preferably to the distributor from whom the machine was purchased. For the Distributor in your
area, call Pioneer Eclipse Customer Service Department at 800-367-3550. If you are dissatisfied with the
service that you receive, call or write Pioneer Eclipse Customer Service Department for further
assistance.
DISCLAIMER OF CONSEQUENTIAL
PIONEER ECLIPSE DISCLAIMS ANY RESPONSIBILITY FOR LOSS OF USER TIME OF THE
PIONEER ECLIPSE MACHINE OF ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGE
EXCEPT AS STATED IN THE WARRANTY APPLICABLE TO EACH MACHINE. EXCEPT AS STATED IN
SUCH WARRANTIES, THE COMPANY DOES NOT OTHERWISE WARRANTY ANY MACHINE AND NO
WARRANTY, EXPRESS, IMPLIED OR STATUTORY IS MADE BY THE COMPANY.
LIMITED WARRANTY
SWING STAR/BUFF STAR MODELS
TO QUALIFY FOR THIS WARRANTY:

1
Your new Pioneer Eclipse Floor Machine will afford you many years of trouble-free operating
satisfaction provided it is given proper care. Prior to packaging, your Pioneer Eclipse Floor
Machine was inspected by a Quality Control Technician.
Uncrating
Your Pioneer Eclipse Floor Machine was protectively
packed to prevent damage in shipment. We suggest that
upon removing the unit from its carton, you carefully
inspect it for any possible damage in transit. If damage is
discovered, immediately notify the transportation company
who delivered your machine. As a manufacturer, we are
unable to act upon any claim for concealed damage; you
must originate the claim.
Important Safeguards
This machine is designed to be safe when used to perform
the functions specified in this Operator’s Manual. Should
damage occur to electrical or mechanical parts, the
machine should be repaired by the manufacturer or
competent service station before using in order to avoid
further damage to the machine or physical injury to user.
Your floor machine is equipped with a safety switch lockout
device designed for your safety. Do not attempt to bypass
or defeat the safety lockout device. Never use any device
to lock the power switch triggers in the ON position.
Warnings
READ THIS OPERATOR’S MANUAL!
WARNING: You must have training in the operation of this
machine before using it.
WARNING: Machines can burn flammable materials and
vapors. Do not use this machine with or near fuels,
grain dust, solvents, thinners or other flammable
materials.
WARNING: Do not operate this machine unless it is
completely assembled.
WARNING: Do not use this machine as a step or to move
furniture.
WARNING: When disconnecting power cord from electrical
outlet, grasp the plug. Pulling it out by the cord itself
can damage cord insulation and internal connection to
plug. To prevent electric shock, always remove the
electrical plug from the electrical outlet before doing
any repairs or maintenance to this machine.
WARNING: To prevent injury, always remove the electrical
plug from the electrical outlet before changing the
polishing pad and before leaving the machine.
WARNING: To prevent injury, keep hands, feet and loose
clothing away from the rotating pad.
WARNING: Maintenance and repairs must be done by
authorized personnel only.
WARNING: Keep all fasteners tight. Keep adjustments
according to specifications.
WARNING: Keep the electrical parts of the machine dry.
For storage, keep the machine in a building.
WARNING: Always use a three-wire electrical system
connected to the electrical ground. For maximum
protection against electric shock, use a circuit that is
protected by a ground fault circuit interrupter. Consult
with your electrical contractor.
WARNING: To prevent damage to the power cord, do not
let the pad, pad driver or wheels touch the power cord
when the machine is running. Always lift the power cord
over the machine.
WARNING: Make sure all labels, decals, warning, cautions
and instructions are fastened to the machine.
175 RPM Models
The Pioneer Eclipse 175 RPM floor machine will operate in
a wide variety of applications. The 175 RPM floor machine
is the most versatile speed in the floor care industry.
Hard Floor Applications
• Dry buffing a buffable finish with a tan, beige or white
pad or brush.
• Scrubbing with green or blue pad or scrubbing brush.
• Stripping with a black pad and a stripping chemical.
Carpet Applications
• Bonnet cleaning with a yarn bonnet and carpet
maintainer chemical.
• Shampooing using a showerfeed shampoo brush and
solution tank mounted to the handle tube containing
carpet shampoo.
WARNING: To prevent injury, always remove the electrical
plug from the electrical outlet before changing the
polishing pad and before leaving the machine.

2
Machine Preparation
To attach the drive block or brush or other attachment, be
sure the handle is “locked” in the upright position.
1. Lay the floor machine on its back with the handle lying
on the floor to expose the driving plate on the underside
of the floor machine.
2. Holding the drive block, brush or attachment in both
hands and straddling the motor with your back to the
handlebox, bend over and fit the three slots of the
clutch plate (built into the back of the brush) over the
three lugs of the driving plate.
3. Turn the drive block, brush or attachment counter-
clockwise as far as it will go until it is seated in the
ready-to-use position.
CAUTION: This is the only proper way to install a drive
block, brush or attachment. NEVER put a drive block,
brush or attachment on the machine by placing it on the
floor and moving the running machine over it, or by
placing the machine over the block or attachment and
then starting the motor.
4. Return the floor machine to upright position and adjust
handle to operating position. Recommended handle
position is close to the waist with arms extended down.
5. Lock the cam release lever into position.
NOTE: The hardened steel cam release lever does not
require extreme tightening to effectively hold the handle
in position. Over-tightening will shorten the functional
life of the lever.
To remove drive block, brush or attachment, lay the floor
machine on its back and disengage clutch plate slots
from driving plate lugs by turning clockwise.
Machine Operation
1. First install the pad driver and pad, brush or other
attachments to be used.
2. Plug the machine in as directed and lower the handle to
the desired operating height and lock in place using the
cam lever handle.
3. Push the safety switch forward and squeeze the switch
triggers beneath the handle grips. This activates the
motor and starts the block, brush or attachment in
operation.
Each time you release the triggers the safety switch will
reset.
You will need to follow the direction above to restart the
machine.
CAUTION: When leaving the machine unattended,
disconnect the wall plug and return the handle to the
“locked” upright position to prevent accidental starting.
Guiding the Machine
To move toward the right, raise the handle slightly. The
higher the handle is lifted, the faster the machine will move
to the right.
To move toward the left, lower the handle until the machine
travels to the left. The more the handle is lowered, the
faster the movement to the left.
Dual-Speed 175/320 RPM
Models
The Pioneer Eclipse dual speed machines will operate in a
broad range of applications. These machines perform all
the applications of the 175 RPM standard speed machines
and the 300 RPM high speed machines except the
specialized applications.
Do not use dual speed machines for sanding, grinding or
scraping.
The dual speed machines are specially designed for spray
cleaning of heavy traffic areas.
Machine Operation
Follow the operation procedures described for 175 RPM
machines.
The proper speed selection is important to properly
operate these machines.
Speed selection Low (175 RPM) or High (320 RPM) is
made with the switch located on the base and motor
housing.
Stripping, scrubbing, bonnet cleaning and shampooing
should be performed at 175 RPM Low Speed.
Buffing should be performed at 320 RPM, High Speed.
Do not store the machine with the drive block, pad or brush
on the machine.
Wipe off the machine housing and wheels to prevent
build-up of unnecessary residue.
Transporting the Machine
1. Place the handle in the upright position.
2. Lock the handle cam release lever.
3. Tip the machine back and transport on the wheels.

3
Machine Maintenance
Once a month remove the motor cover and vacuum out
any dust or debris which has accumulated on the motor.
Replace the motor cover by setting it over the holes in the
housing and replace all of the screws. Check and maintain
the tightness of all the fasteners.
WARNING: Do not over-tighten the switch housing screws.
Keep the machine clean especially at the handle tube and
collar so the handle tube will move freely through the
collar. Inspect the cord for cuts, gashes, or loose prongs;
replace as needed.
Disassembly of this motor voids the warranty. Improper
disassembly and assembly of this motor can permanently
damage the field or rotor.
Troubleshooting
Machine does not run.
The circuit breaker has tripped. Allow the circuit breaker 2
minutes to cool before resetting. Plug is broken or has
loose contact. Replace.
Prevent circuit overload.
Check the pad and change it if it is rough or dirty. Spray
buffing or spray cleaning is not a substitute for
scrubbing or mopping a floor. Eliminate any extension
cord that is smaller than 12/3 wire or greater than 25
feet in length. Unplug anything other than the machine
from the circuit or locate another circuit.
Machine will not start.
Circuit breaker is not reset. Reset breaker.
Plug is broken or has a loose contact. Replace.
Circuit breaker is defective or weak. Replace.
Switch is defective. Replace switch.
Machine will not reach operating speed.
Unplug anything else other than the machine from the
circuit or locate another circuit.
Motor runs but pad or brush does not turn.
Coupling is broken. Replace. Coupling is not covered
under warranty. Do not attempt to place a running
machine over a block or brush. Always place and
remove the block or brush by hand.
Safety Instructions
This Floor Machine should be grounded while in use to
protect the operator from electric shock.
This machine is equipped with a 3-conductor cord and a 3-
prong grounded type attachment cap plug to fit the proper
grounding type receptacle. The green (or green and
yellow) conductor in the cord is the grounding wire. Never
connect this wire to anything other than the grounding
blade.
The Floor Machine is provided with an attachment cap
plug, as shown in Sketch A, and is intended for use on a
nominal 120 volt circuit. If a properly grounded receptacle,
as shown in Sketch A, is unavailable, an adaptor, as
shown in Sketch C, is available and should be installed, as
shown in Sketch B, if the outlet box that houses the
receptacle is grounded. Be sure to fasten the grounding
tap to the faceplate screw.

4

5
WARNING
TO AVOID FIRE, DO NOT USE WITH A
FLAMMABLE OR COMBUSTIBLE LIQUID
TO CLEAN FLOOR.
READ ALL INSTRUCTIONS, WARNINGS AND
CAUTIONS BEFORE USING EQUIPMENT.
These guidelines are presented for your protection and convenience. Please read them carefully, since a failure to heed
these precautions could result in discomfort or injury. When using an electrical appliance, basic safety precautions
should always be followed.

6

7
Ref Part Number Description
1 M1369GS 14/3 stwa, 50' gray cord with strain relief
2 SR36 strain relief washer
3 X8008N nut, lock, 1/2" steel conduit
6 X8012 clamp, collor, handle
7 X8013 cord hook, plated
8 X8207 screw, 10-24 x 1/2", phph, type "f"
9 X8012A handle tube clamp lever assembly (excludes clamp collar)
10 X8016 knob, plastic, handle release
11 X8807R handle brace, right
12 X8807L handle brace, left
13 X8809 pivot shaft, 1/2" x 12-7/8"
14 X8019 axle wheel
15 X8020 washer for axle
X8265 bolt for axle
16 X8024 wheel 5" x 1 1/4"
17 X8028 washer, cam, w/slot
18 X8953 start capacitor 450 UF 125V
X8954 run capacitor 50 UF 370V
X8909 1.5 hp gear motor assembly
X8955 start capacitor 380 UF 125V
X8956 run capacitor 60 UF 370V
19 X8042A motor cover
21 X8046 35 UF 370V run capacitor for Doerr 1-1/2 HP Doerr Model
22 #R07559 & G51400
X8056 310 UF 125V start capacitor for 1 1/2 HP Doerr Model
#R07559 & G51400
23 X8022 cord, in-line 14/3 sjtwa 49"
24 X8030I bumper 38.25" blu/blk
25 X8151B plug, plastic, 7/16" hole
26 X8258A bumper, blk, 1.13" od x .75" h
27 X8258AS #8 x 1" phph type "a"
28 X8278 3-32 x 1/2" phph, black oxide
29 X8821 screw, 8-32 x 3/4", thph, blk plated (2)
30 X8822 spacer, plastic blk, #8 x .25 (2)
31 X8212 1/4" spring lock washer
32 X8218 washer, flat, SAE 5/16"
33 X8219 3/8"SAE flat washer
34 X8222 1/4-20 x 3/16" socket set
35 X8226 1/4-20 x 1 1/4 hex head cap
36 X8272 screw, 8-32 x 1/2", truss/ph (4)
58 X8912 switch box cover
59 X8914 thumb actuation release
60 X8917 handle trigger
61 X8916 trigger tension spring (2)
62 X8915 handle trigger thumb actuator spring
63 X8918 handle roll pin (2)
64 X8941 1" handle grip (2)
65 X8207 #10-24 screw (3)
7CY001 lock washer (3)
66 X8923 insulation sheet
67 F5P switch
68 X8911 1-1/2" dia. handle tube weldment
69 7BG004 7/16" diameter grommet
70 X8222 1/4-20 x 3/16" set screw
NOT ILLUSTRATED
PX7 Switch for M172-3, M202-3
PX28 Insulation boot for switch

8

9
Ref Part Number Description
8 SR37 strain relief, metal
8A X8100 counter nut
8B X8228 spacer
8C SR37A brass sleeve strain relief
11 X8011B handle tube, 1-1/2" w/bushings
12 X8012A handle clamp assy
13 X8013 cord hook
15 X8210 wheel screw
17 X8027L left brace
18 X8027R right brace
19 X8018 pivot shaft
20 X8029 axle
24 X8025 4" wheel
25 X8202 8 - 32 x 1/2” pan bolt
26 X8150M mount for capacitor strap
28 X8256 keep nut
29 X8150 capacitor strap
30 X8059 motor and gear unit
31 X8039 340 MFD capacitor
32 X8041 motor cover
33 X8058 base housing, 13"
34 X8207 motor ground screw
35 X8152 D-washer
36 X8229 1/4"-20 x 3/4" phillips head screw
37 X8225 3/16" cut washer (2 req.)
38 X8208 10-24 x 5/8" phillips head machine screw (2 req.)
41 X8030E 30" bumper
42 M1400C 14/3 SJTWA cord, 50'
M1400CS 14/3 SJTWA 50' cord with metal strain relief and flag terminal
43 X8207 cord retainer screw (2 req.)
44 X8101 spring washer (2 req.)
45 X8020 axle washer
46 X8022B handle line cord assembly
NOT ILLUSTRATED
X8108 wheel spacer
X8222 1/4"-20x3/4" socket set screw for X8011 handle
X8590 upper motor bearing
F3P motor coupling
SW47 stationary switch
X8210-1 short switch housing screw and nut
X8220 long, switch housing screw

© 2004 Amano Pioneer Eclipse Corporation
P.O. Box 909
Sparta, NC 28675
1-800-367-3550; 1-336-372-8080
Fax: [phone]
www.pioneer-eclipse.com
LT043900, 9/04