Pioneer SGY-PM910H2 User manual

1
SGY-PM910H2/HL/HR
Installation Manual（for dealers）

2
Table of Contents
Table of Contents...............................................................................................................................................2
1 Preparations...................................................................................................................................................4
1.1 Confirm the products..............................................................................................................................4
1.2 Outline of procedure ...............................................................................................................................4
1.2.1 For the SGY-PM910HL/HR with an ANT+ cycle computer...........................................................4
1.2.2 For the SGY-910H2/(HL+HR) with an ANT+ cycle computer .......................................................4
1.2.3 For the SGY-PM910HL/HR/(HL+HR)/H2 with a SGX- CA500 .....................................................5
1.3 Product mode ..........................................................................................................................................6
Pedaling monitor mode:.................................................................................................................................6
•Dual power meter mode: .............................................................................................................................6
Single power meter mode: .............................................................................................................................6
The power value of the left or right sensors can be doubled and displayed quickly and the cadence can be
measured. Can be used with SGX-CA500 or with a Cyclocomputer that supports ANT+ from another
manufacturer .................................................................................................................................................6
2 Mode Select ....................................................................................................................................................6
2.1 Switching to the pedaling monitor mode•.............................................................................................6
2.1.1 Press the menu button on the CycloMeter screen of SGX-CA500.................................................6
2.1.2 Tap [Option] - [Pedaling settings] - [Mode Switch] in this order...................................................6
2.1.3 Tap on the device number display part. .........................................................................................6
2.1.4 Enter the device number and tap [ ].....................................................................................7
2.1.5 Rotate the bicycle’s crank set more than three rotations to start the left and right transmitters.
7
2.1.6 Tap [Pedaling Monitor]. ..................................................................................................................7
2.1.7 Add in the sensor list of SGX-CA500..............................................................................................7
2.2 Switch to dual power meter mode..........................................................................................................8
2.2.1 [Method 1] Switch by pushing the push switch in the right transmitter .....................................8
2.2.2 [Method 2] Switch the mode on SGX-CA500................................................................................10
2.3 Switch to single power meter mode .....................................................................................................11
2.3.1 [Method 1] Switch by pushing the push switch in the right transmitter ...................................11
2.3.2 [Method 2] Switch the sensor mode from SGX-CA500 ................................................................11
3 Magnet Detection and Calibration..............................................................................................................12
3.1 Temporarily affix the Magnet ..............................................................................................................12
3.1.1 Use masking tape to temporarily attach the Magnet Patch .......................................................12
3.1.2 Rotate the rank to confirm the position of the magnets. .............................................................12
3.1.3 Temporarily affix the Magnet. ......................................................................................................13
3.1.4 Turn the crank slowly. ...................................................................................................................13
3.2 Magnet Detection (For cycle computer other than Pioneer)...............................................................13

3
3.2.1 Preparations ..................................................................................................................................13
3.2.2 Detecting the Magnet Position .....................................................................................................13
3.3 Magnet Calibration （Using the SGX-CA500）.................................................................................14
3.3.1 Preparations ..................................................................................................................................14
3.3.2 Detection of Magnet Position ........................................................................................................14
3.3.3 Fixing the Magnets........................................................................................................................15
3.3.4 Magnet Calibration .......................................................................................................................15
4 Pairing with the Cyclocomputer .................................................................................................................16
4.1 Check the sensor modes. ......................................................................................................................16
4.2 Rotate the crank at least three times to start up both sensors. .........................................................16
4.3 Select the Sensor to connect on the Cycle Computer SGX .................................................................16
4.4 Press [Search]. ......................................................................................................................................17
5 Zero Calibration...........................................................................................................................................18
5.1 Select Zero Calibration.........................................................................................................................18
5.2 Start Zero Calibration (Press [ZeroCal]) .............................................................................................18
5.3 Checking the Calibration Results........................................................................................................19
5.3.1 Check that the crank is detecting no load. ...................................................................................19
6 Copy pedal....................................................................................................................................................20
6.1 Press the menu button on the CycloMeter screen...............................................................................20
6.2 Tap [Option] then [Pedaling settings] and then [Pedaling Copy].,and select the copy method. .......20
6.3 To change the balance, tap [L:R Balance]............................................................................................20
6.4 Tap [+], [-] and change the numerical value and tap [OK]. ................................................................20
7 Operation Check(Using the SGX-CA500 only)...........................................................................................21
8 Troubleshooting ...........................................................................................................................................22
9 Error Code (Using the SGX-CA500) ...........................................................................................................26

4
1 Preparations
1.1 Confirm the products
The operations necessary to install the Pedaling Monitor System on the customer’s bicycle depend on which System it
is; SGY-PM910HL/HR or SGY-PM910H2, and on which cycle computer is being used; SGX-CA500, SGX-CA900, or
some other manufacturer’s product.
1.2 Outline of procedure
1.2.1 For the SGY-PM910HL/HR with an ANT+ cycle computer
Single Power Meter Mode:（SGY-PM910Hl/HR Factory Default Mode）
1. [3.1Temporarily affix the Magnet]: Attach the magnet to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should flash
Orange for ten seconds
3. [3.2 Magnet Detection]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the
magnet.
4. ［3.3.3 Fixing the Magnet］: Fix the magnet in place.
5. [4 Pairing with the Cyclocomputer]: Pair the sensor with the cycle computer.
6. [5 Zero Calibration]: Carry out Zero Calibration.
1.2.2 For the SGY-910H2/(HL+HR) with an ANT+ cycle computer
Dual Power Meter Mode:（SGY-PM910H2 Mode on shipment from Installation center）
1. [3.1Temporarily affix the Magnet]: Attach the left and right magnets to the frame temporarily.
2. [2.2.1.3 Check the Current Mode]: Remove then replace the magnet, and observe the LED. It should light
Orange for ten seconds.
3. [2.2 Mode Switching]: If the LED flashed in step 2, it is necessary to switch the mode to Dual Power Meter
Mode.
Push the button on the right side transmitter for two seconds, and the LED will flash quickly in Orange for ten
seconds. While this is happening, release the button and press it again for two seconds. The LED will then light in
Orange for ten seconds.
4. [3.2.2Detecting the Magnet Position]: Confirm that the magnet can be detected.
Within five minutes of replacing the battery, rotate the crank and confirm that the LED flashes when passing the magnet.
5. [3.3.3Fixing the Magnets]: Fix the magnet in place.
6. [4Pairing with the Cyclocomputer]: Pair the sensors with the cycle computer using the device number of the
right side sensor.
7. [5Zero Calibration]: Carry out Zero Calibration.

5
1.2.3 For the SGY-PM910HL/HR/(HL+HR)/H2 with a SGX- CA500
Pedaling MonitorMode:
1. [3.1Temporarily affix the Magnet]: Attach the left and right magnet(s) to the frame temporarily.
2. [2.1 Mode Switching]: Switch to Pedaling Monitor Mode.
Using a SGX-CA500 with Firmware of Version 20150501.02.43 or higher, input the device number of either or both
sensors and switch the mode to Pedaling Monitor Mode. Once this is successful, the Sensor LED will light in
Green for ten seconds.
3. [3.3.3Fixing the Magnets]: Fix the magnet in place
4. [3.3.4Magnet Calibration]: Carry out Magnet Calibration.
5. [4 Pairing]: Pair the sensors with the cycle computer using the Pedaling Settings Menu in the SGX-CA500.
6. [5Zero Calibration]: ：Carry out Zero Calibration.
7. [6Copy pedal]：If using only one sensor SGY-PM910HL/HR; Set up the Pedal Copy function on the
SGX-CA500.
8. [7Operation Check]

6
1.3 Product mode
When using SGX-CA500, the firmware version is required to be 20150501.02.43 or higher.
Pedaling monitor mode:
When paired with Cyclocomputer SGX-CA500, the pedaling efficiency and cadence and other such properties can be
measured. You can make maximum use of the functions of this product.
•Dual power meter mode:
Left and right sensors are required. The actual power values of the left and right sensors can be totaled and displayed
and the cadence can be measured. Can be used with SGX-CA500 or with a Cyclocomputer that supports ANT+ from
another manufacturer.
Single power meter mode:
The power value of the left or right sensors can be doubled and displayed quickly and the cadence can be
measured. Can be used with SGX-CA500 or with a Cyclocomputer that supports ANT+ from another
manufacturer
2Mode Select
When using SGX-CA500, the firmware version is required to be 20150501.02.43 or higher.
2.1 Switching to the pedaling monitor mode•
• Cyclocomputer SGX-CA500 is required to switch to the pedaling monitor mode. The mode cannot be switched with
cyclocomputers from other manufacturers.
・The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of
a different version, update the firmware. Refer to the User's Guide (For WEB) of SGX-CA500 regarding how to update or
any other operation method.
http://pioneer-cyclesports.com/us-en/support/products/http://pioneer-cyclesports.com/jp/support/products/
2.1.1 Press the menu button on the CycloMeter screen of SGX-CA500.
2.1.2 Tap [Option] - [Pedaling settings] - [Mode Switch] in this order.
The mode switching screen opens. If the device number is already
displayed, confirm that it is the same as the device number of the sensor you
want to use. If it is the same, the input operation is not required.。
If the device number is different from the sensor you want to use, enter the
new number. Remove the check from the sensors whose mode is not to be
switched.
2.1.3 Tap on the device number display part.
The sensor device number input screen opens.

7
2.1.4 Enter the device number and tap [ ].
The device numbers are printed on the right junction box and on the side of the left sensor.
2.1.5 Rotate the bicycle’s crank set more than three rotations to start the left and right
transmitters.
•Pair with the Cyclocomputer within 5 minutes after the transmitters are
activated.
2.1.6 Tap [Pedaling Monitor].
The search for the sensor starts. A [Please wait.] message appears.。
•It may take more than 1 minute to pair with the sensor.
The mode switching completion screen opens. Tap OK if you want to add in
the sensor list.
2.1.7 Add in the sensor list of SGX-CA500
If you do not add the sensor in the sensor list, the SGX-CA500 will not pair
with the sensor.
You can add the sensor in the sensor list later, using the [Sensors] menu.。
When the mode is switched, the LEDs of the sensors light green for 10
seconds. When it is added in the sensor list, it pairs with SGX-CA500.
Hereafter, whenever the sensor is started, it will automatically pair with
SGX-CA500.
To confirm the sensor list, press the menu button on the left of the product
on the main screen of the CycloMeter and tap [Sensors]. The display on the
mode switching completion screen is as follows depending on the status.•
[Success] Mode is switched.
[Timeout] Sensor is not found.
[Cancel] Cancel is pressed.
[Low Battery] The battery is almost empty.
• Timeout: Communication status is likely to be poor. Sensor information
cannot be received properly. Make sure that the sensor you are pairing is activated, then bring the SGX-CA500 closer to
the sensor and perform the pairing operation again. Pairing with the sensor may not be possible due to interference in the
same frequency band. If “Timeout” is displayed even by operating after moving SGX-CA500 closer to the sensor and
pairing with it, try again someplace where there is no interference from microwaves, radio waves, or wireless equipment.
・Low Battery: The battery is almost empty. Remove the battery and replace with a new one.

8
2.2 Switch to dual power meter mode
• Both the left and right sensors are required in this mode. Cyclocomputer SGX-CA500 is required when the sensor
changes to the pedaling monitor mode. It cannot be switched by using cyclocomputers from other manufacturers.
•The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of a different version, update the
firmware. Refer to the User's Guide (For WEB) of SGX-CA500 regarding how to update.
http://pioneer-cyclesports.com/us-en/support/products/
The mode can be switched in two ways.
[Method 1] Switch by pushing the push switch in the right transmitter
[Method 2] Switch the mode on SGX-CA500
2.2.1 [Method 1] Switch by pushing the push switch in the right transmitter
When using a Cyclocomputer from another manufacturer, switch with this method.
2.2.1.1 Loosen the screws on the right transmitter cover and remove the cover.
2.2.1.2 Replacing the batteries of theleft and right transmitters.
The operation is enabled for 5 minutes after the batteries are installed. Switch within 5 minutes. If more than 5 minutes
elapse, re-install the batteries of the left and right sensors.
2.2.1.3 Confirmation of the actual sensor mode.
When the batteries are installed, the LEDs on the left and right transmitters light as follows depending on the actual
sensor mode.
• When it is in pedaling monitor mode: The LEDs light green for 10 seconds
• When it is in dual power meter mode: The LEDs light orange for 10 seconds
• When it is in single power meter mode: The LEDs blink orange for 10 seconds
2.2.1.4 Switch the sensor mode.
• Before switching the mode, confirm that there is no other
pedaling monitor nearby. If this is not done at a sufficient
distance away from other sensors, the other sensors are likely to
malfunction.

9
By pushing the push switch in the right transmitter for more than
3 seconds, the LEDs on the right transmitter blink green. When
communication with the left transmitter is enabled, the LEDs on
the left and right transmitters rapidly blink orange. Confirm that
the LEDs on the left and right transmitters blink when the mode
is switched. (If they do not blink, the communication may have
been done with another pedaling monitor sensor by mistake.
Move somewhere away from the other bicycles and do the
operation again.)
While the blinking takes place rapidly for 10 seconds, push the
switch again during that time for more than 3 seconds. The mode
is switched to the dual power meter mode. When the mode is
switched, the LED starts lighting orange for 10 seconds. If you do
not push long while the LEDs are rapidly blinking orange , it is
canceled and so, you must do the operation again.
•It may take several seconds to switch the sensor mode
depending on the radio transmission conditions.
If the pairing with the left transmitter fails, the LEDs of the right
transmitter blink red 5 times. Since the left transmitter may be in
the pedaling monitor mode, switch to the
single power meter mode first on Cyclocomputer SGX-CA500
and do the above operation. If it still fails, remove the batteries
from the left and right transmitters; wait for more than one
minute. Place the batteries back and do the operation again.
After the mode is switched, install the right transmitter cover
and tighten the screws to fix it in place. Use a tool that can
measure the torque to tighten the screws.
•Tightening torque: 30 cN·m
・install the transmitter cover and the screws in firmly to ensure
water resistant performance.
• 防水性能を保つため、送信機カバーおよびネジは確実に取り
付けてください。
・•Do not lose the water-proof packing.
For how to pair with the cyclocomputer, when using SGX-CA500,
refer to Page 24 and if using a cyclocomputer
From another manufacturer, refer to the User's Manual of that
cyclocomputer
.

10
2.2.2 [Method 2] Switch the mode on SGX-CA500
Go to the mode switching screen.
2.2.2.1 If the left and right sensors are checked, tap [Dual Power].
The mode switching completion screen opens.
In this state, the cyclocomputer is still not paired with the
sensor.
If the mode cannot be switched, refer to 2.1.7Add in the
sensor list of SGX-CA500.
When the mode is switched, the LEDs of the sensors light
orange for 10 seconds.

11
2.3 Switch to single power meter mode
・If the actual sensor mode is pedaling monitor mode, switch it on SGX-CA500.
・The firmware version of SGX-CA500 needs to be 20150501.02.43 or higher. If it is of
a different version, update the firmware. Refer to the User's Guide (For WEB) of SGX-CA500 regarding how to update.
http://pioneer-cyclesports.com/us-en/support/products/
The mode can be switched in two ways. Select according to the actual sensor mode.
[Method 1] Switch by pushing the push switch in the right transmitter
[Method 2] Switch the sensor mode from SGX-CA500
2.3.1 [Method 1] Switch by pushing the push switch in the right transmitter
・When using a Cyclocomputer from another manufacturer, switch with this method.
・When it is in the dual power meter mode, if the left and right transmitters are not started, the mode cannot be switched
to the single power meter mode.
Rotate the crank set of the bicycle and start the sensor. When it is in dual power meter mode, if you push the push switch
in the right transmitter for more than 3 seconds, the mode changes to single power meter mode and the LEDs blink
orange for 10 seconds.
When the LEDs blink red, the left transmitter may not have started. Start it again.
When the sensor is in pealing monitor mode, it does not change to the single
power meter mode, even on pushing the push switch. Switch using method 2.
2.3.2 [Method 2] Switch the sensor mode from SGX-CA500
If the mode is pedaling monitor mode or dual power meter mode, switch using the SGX-CA500.
Go to the mode switching screen. Check the sensor you want to use, then select single power and switch the mode.
For how to pair with the cyclocomputer.
When the mode is switched, the LEDs of the sensors blink orange for 10 seconds.

12
3 Magnet Detection and Calibration
3.1 Temporarily affix the Magnet
3.1.1 Use masking tape to temporarily attach the Magnet Patch
The adhesive on the back of the Magnet Patch is very strong, so do not remove the backing paper until the Magnet
position is confirmed.
In most cases, the Magnet Patches should be
used rather than the Arm Type. If the Patch Type
Magnets result in a distance from the Sensor of
more than 10.7mm, then use the Magnet Patch
Spacer to reduce the distance, or, if the Sensor
to Magnet distance is outside the range 1.5 –
10.7mm then use the Arm Type Magnets.
Caution: Even when using the Magnet Patch
Spacer, attach the Magnet temporarily first until
the position of the Magnet is confirmed. When
confirmed, attach the Spacer to the frame first,
then attach the Magnet to the Spacer
3.1.2 Rotate the rank to confirm the position of the magnets.
The Magnet should be in one of the positions shown below, on a circle around the crank axis.
The radius of this circle should be such that the Magnet passes the magnetic sensor
Approximate distance from axis of crank for magnets:
Left side: 53mm from Crank Axis.
Right Side: 42mm from Crank Axis.
Left Side Photo shows three possible options for Magnet Position.
Only one magnet is required on each side.
左側： 右側：
①①
Left Ri
g
ht
①= Sensor
Attach the magnet so that when
the crank is rotated, the sensor
passes over it in the direction
shown.
Magnet Patch Spacer
Attach this
side to the
frame.
Attach the
Magnet
Patch to
this side.
3.6mm

13
3.1.3 Temporarily affix the Magnet.
For the left and right sides, try to
affix the magnet so that it is within
1.5mm and 10.7mm of the sensor. If
this is not possible on the Chainstay,
try the Seat Tube (right photo) or the
Down Tube.
If this distance range cannot be
achieved, try using the Magnet Patch
Spacer.
3.1.4 Turn the crank slowly.
Check that the magnet does not come in contact with the senso.
3.2 Magnet Detection (For cycle computer other than Pioneer)
If using a cycle computer other than Pioneer, the magnet position can be checked as follows.
3.2.1 Preparations
Set the bicycle on a roller or other stand.
Remove then replace the batteries in the sensors. (Check must be done within five minutes.)
3.2.2 Detecting the Magnet Position
Rotate the crank slowly at around 30rpm. Check that the LED on each sensor lights up green once in very resolution.
If this is successful proceed to 3.3.3Fixing the Magnets.
If the LEDs do not light: either the sensor is too far from the magnet, or the magnet is not in the sensor’s path. Check
3.1Temporarily affix the Magnet の again.
LED lights green

14
3.3 Magnet Calibration （Using the SGX-CA500）
When using both left and right sensors with the SGX-CA500 cycle computer, Magnet Calibration is necessary.
・Magnet Calibration allows the sensors to detect the precise position of the magnet. This is essential for correct display
of the force vectors so please ensure that it is done correctly.
・Magnet Calibration requires the SGX-CA500 cycle computer. It cannot be done with other cycle computers. Also, the
sensors must be in Pedaling Mode.
・The firmware of the SGX-CA500 must be version 20150501.02.43 or higher. If this is not the case, please update the
firmware. Details of how to do this are available on the following website.
http://pioneer-cyclesports.com/jp/support/products/
3.3.1 Preparations
Use a roller or other stand to hold the bicycle upright with the front and back wheels at the same height. Rotate the crank
at least three times to activate the sensors.
3.3.2 Detection of Magnet Position
With the magnets attached temporarily as described in section 3.1Temporarily affix the Magnet, navigate to the Magnet
calibration screen on the SGX-CA500.
[Options] -> [Pedaling Settings] ->[Magnet Calibration]
Rotate the crank slowly at around 30rpm, and check that the count rises once per revolution. If the count does not rise,
check the position of the magnets again. Note! Do not press [Calibration Start] yet!

15
3.3.3 Fixing the Magnets
Being careful not to move the Magnets from their measured position, fix the Magnets in place.
Remove the masking tape on one side of the Magnet only. Remove the backing tape on the back of the Magnet, and affix
it permanently to the position in which it had been temporarily affixed.
3.3.4 Magnet Calibration
After 3.3.3Fixing the Magnets, then Magnet Calibration is performed. Press [Calibration Start].
Rotate the crank slowly at around 30rpm, and check that the count in the [Magnet Calibration] screen rises on each side
for each rotation. When the count reaches 5/5 or higher, the [Save] button becomes active. Press the [Save] button to
store the Calibration results. A message will be shown indicating Calibration success, then press [OK.] to conclude.

16
4 Pairing with the Cyclocomputer
This section describes how to pair the installed pedaling monitor sensors on your bicycle to the SGX-CA500
Cyclocomputer.
If you are using this product with a Cyclocomputer from another manufacturer, the method of pairing is different. Refer to
the User’s Manual of the Cyclocomputer you are using.
In the chapter“ 2.1.7Add in the sensor list of SGX-CA500 ", already, if you are paired, the following process is not
required.
4.1 Check the sensor modes.
The actual sensor mode can be confirmed from the way the LEDs of the sensors light when the batteries are installed, or
from the way the LEDs light on switching to each mode.
4.2 Rotate the crank at least three times to start up both sensors.
4.3 Select the Sensor to connect on the Cycle Computer SGX
On the SGX-CA500, press the [Menu] button, then select [Sensors] – [Connect New] – [Device Type] –
[Pedaling Monitor R].。

17
4.4 Press [Search].
If the [Error Rate] shows an [OK} result, then connection has been successful.
If the search continues for more than a minute, go back to 4.1Check the sensor modes. 1 to restart the sensor and try
the search again..
Pairing of the right transmitter is completed. Pair the left transmitter in the same way.

18
5 Zero Calibration
Zero Calibration can be performed using the Cycle Compuｔer SGX-CA500
1 Place the bicycle in a vertical, level position (Both wheels at the same height)using a roller or stand.
2 Rotate the crank at least three times to start up both sensors.
3 Place the crank arm in a vertical position (with the pedals attached)
5.1 Select Zero Calibration.
On the SGX-CA500, press the [Menu] button, then select [Options] -> [Pedaling Settings] ->[ZeroCal].
5.2 Start Zero Calibration (Press [ZeroCal])
If successful, the [Result] box will show [Success].
If [Failure] is shown, it is possible that
the crank moved during the
calibration. Please retry with the
crank in a stable position.
Note:

19
5.3 Checking the Calibration Results
Check that the sensor has been calibrated correctly.
5.3.1 Check that the crank is detecting no load.
In the Force Preview screen of the SGX-CA500, the figures shown should be within the following range.
Tangential Force : 0 +/- 3N
Radial Force: 0 +/- 3N
If numbers outside this range are shown, it is possible that the crank moved during
the calibration. Please retry with the crank in a stable position.