Pivot OB MONITOR User manual

1
＋
User’s
Manual
(This Book)
Please check the contents of the package
Zip Ties
(Large) × 2
(Small) × 2
(OBM As of October, 2019 No.4)
Cut
Connector
Monitor Unit OBD Cable
with fuse 3A
IGN Cable
with fuse 3A
●This product cannot be installed in non-compatible car models.
●Make sure to keep car stopped while working and be aware of the ventilation, such as exhaust emission.
●Do not operate while driving to prevent an accident.
●Do not crush the cable, nor nipped by metals or something.
●Please securely fasten the product not to fall the product while driving.
Improper use or disregard of these warnings may result in the injury or death of people.
WARNING
●The display will not be proper if the ECU being used is not the standard one or if a sub-computer is
being used, even in compatible car models.
●Cannot be used in combination with other company’s products that use Diagnostic Monitoring
Connectors.
●For details about using in combination with other PIVOT products that use Diagnostic Monitoring
Connectors please see our Web Site at https://pivotjp.com/obd-e/
Improper use or disregard of these warnings may cause injury to persons, damage the product and other things.
OB MONITOR
Compatibility
List
Contents
Double-sided
Tapes
[45 ×14 mm] × 2
[25 × 35 mm] × 1
[14 × 14 mm] × 1
L-shaped
Fastener
OBD MULTI MONITOR with OLED DISPLAY
CAUTION
Thank you for purchasing PIVOT product.
Please read this manual carefully and keep it for future reference.
USER’S MANUAL
Product
●If this product is given to another
user, make sure to include this
User’s Manual.
Product Number :
OBM
()
Contents / WARNING / CAUTION……… 1
Features …………………………………… 2
Part Names of Monitor …………………… 2
Connecting The Connectors …………… 2
Installing The Product …………………… 3
Setting Communication System ……… 4
Operation ………………………………… 5~6
Display Items and Range ……………… 7
Troubleshooting …………………………… 8
(Self-Adjusting Brightness)……………… 8
(Change the power source to IGN) …… 8

2
OBM
装着後は必ず説明書に沿った車種別 の通信方式に設定してください。 Make sure to carry out communication system settings for each car type according to User's Manual after installing.
装着後は通信 方式を設定する
ユニット
品番
MONITOR
OBD
OB MONITOR
コード
No.
8 21
Features
Part Names of Monitor
■Easy installation
Simply connect to the diagnostic monitoring connector.
Compact Easy-to-read Next-generation OBD Multi-Monitor
■Compact and Easy-to-read
Our special scale design coupled with the high contrast and wider field of view offered by
organic EL brings you an easy-to-read compact multi monitor that won't interfere with the
standard built-in meters or look like it was just added onto the dashboard.
■Single-display and Multi-display
The display can be easily switched between our specially designed analog/digital single display
type and a digital triple display type to meet your needs.
■Switch Display Areas
The single display can be also be easily switched to show an analog display of boost or vacuum
and the easy-to-read numerical area can be changed to view such values as motor and engine
rpm for hybrid cars.
The display will automatically adjust brightness to fit the ambient light conditions; making sure it
is not blinding at night. Also, if the car interior becomes overheated, the display brightness will
self adjust to lessen a decrease in performance.
■Self-Adjusting Brightness
Size [Unit：
mm]
Unit
Monitor
Depth 14
27
68
70
Depth 22
50
1MODE Switch
2UP Switch Use to change display items.
3DOWN Switch
Display each data.
4Display
Use to change display items.
Sense the ambient brightness.
5Light sensor
Switch Single and Multi-display.
(Long press = Display and reset of Peak value)
①Insert Connectors of the Monitor and the OBD Cable to the Unit.
②Insert the OBD Connector to the Diagnostic Monitoring Connector.
Connecting The Connectors
Diagnostic
Monitoring
Connector ②
①
①
Connector OBD Cable
Connector
Unit
【Reference】Notes about using the OBD Connector
Make sure to grip the dis-
tended portions when pull-
ing it out or inserting it. Do not pull on the wires when
trying to remove the connector;
the wires may become discon-
nected.
CAUTION
(0.5 m)
(1.5 m)
Monitor
See included [Compatibility List] to check the
position of the Diagnostic Monitoring
Connector.
If you unable to get a grip
on the distended portions.
If you unable to get a
grip on the distended
portions.
In such case, pull
out the connector
by pulling on the
end of the zip tie.

3
Installing the Product
●Fastening to a Flat Place
●Directly mounting
●When Fastening to a Cable or Pipe
(Example of Installation)
Installing the Monitor
Installing the Unit
●Using L-shaped Fastener
On the back side
of the under cover
On the inside of
the kick panel
Under the steering
column cover
Do not install into low positions
(Example of Installation)
Double-sided
tape
[25 × 35 mm]
Unit
Zip tie (Large)
Through holes
Thick cable or pipe
Clean to
remove oil
and dust.
As shown in the diagram below, fasten the unit into
positions not usually affected by water.
Double-sided tape
[45 ×14 mm]
Clean to remove oil and dust.
Affix with double-sided
tape to the mounting
side of the monitor.
Install to a position which is easy to see and which allows for easy operation.
Bundle away all wires While in use if wires become free they may interfere with driving and cause accidents.
Also, wires which are smashed or crushed may result in a short out and can be extremely dangerous.
(Example of Installation)
When mounting on higher positionWhen mounting on lower position
Double-sided tape
Double-sided tape

4
START
ENGINE
STOP START
UP
Press for 5 seconds
UP
DOWN
TOYOTA
Engine Start Press the UP switch for 5 seconds
12
3
Confirm the setting item.
45
Setting Communication System
【Set】
【Before setting】
The setting items will change with each pressing UP / DOWN switch.
Select proper Communication-system.
Setting completed
Real-time display
(READY mode in Hybrid cars)
Must be set after mounting product
(Press the MODE switch, or
automatically fixed after 5 seconds.)
Note that the setting of Communication-system is stored. No need re-setting when you unplug the OBD connector
or replace the battery.
Please make sure to set proper
setting. If the car which needs
to be set Communication-
system C set to others, it will
cause the battery goes flat.
アイシス
車名 年式
H 21.9
〜
3ZR-FAE
エンジン型 式 通信方式 回転
○
水温
○
A
2ZR-FAE
e.g.) TOYOTA Isis (from Oct. 2009)
Find proper setting on Compatibility List
Check this column
Check the Communication-system of installing car on included Compatibility
list. (” 通信方式
means Communication-system on the chart.)
Compat-
ibility List
Compat-
ibility List
Note: You can move to setting even
if the monitor is during display or
off at this time.

5
8 21
801
531
218
51
51
01
0 1
5 31 53
0 6
5 2
5 8
54
82
5 8
UP
DOWN
4 7
//
Operation
Switch the Display mode
12 Single-display example Multi-display example
Switch Display Items on the Single-display
BOOST Vacuum Engine RPM Motor RPM
【Switch Display Areas】
【Each Display Item】
Switch between Single-display and Multi-display
1
Water Temp Voltage Engine RPM
BOOSTMotor RPM
Vacuum Oil Temp Intake Temp
Communication-system Communication-system
Setting Complete
Change
Display
Note that display item is different by Communication-system (See page 7 of this manual).
Note that it’ s not display each value.
Press the MODE switch
during display
Single-display and
Multi-display will change
with each pressing
of the MODE switch
In the following Communication-system, automatically switch display areas in accordance with the reading value of analog display.
Display Items will change with each pressing of the UP / DOWN switch.
【Each Analog Display Dial】
Water Temp Voltage Engine RPM BOOST
Motor RPM Vacuum
Oil Temp Intake Temp
50 8
100
0
0
5000
5000
0
-50 -100
0
50 100
0
50 100
100 150
10
15
°C V rpm
rpm kPa
kPa
BOOST
070
100 200
kPa °C °C
(Note) Only for Communication-system is M.
(See Note)

6
58
531
0035
5 8
801
531
Pressing
for 3 seconds
Pressing
for 3 seconds
58 531 53
5 4
0 6
52 270
82
47
0035
58125
45
60
315
0028
74
Voltage Engine RPM Vacuum
Motor RPM BOOST
Oil Temp Intake TempWater Temp
Water Temp Voltage Engine RPM Vacuum Oil Temp
Motor RPM BOOST
Intake Temp Run Time
マルチ表⽰の場合
Change display item of
by each pressing
1
2
Switch Display Items on the Multi-display
X
Y
Z
X
Change display item of
by each pressing
Change display item of
by pressing for 3 seconds
Y
Z
Setting Complete
【Each Display Item】
Each display will change with
following operation
during Multi-display
Note 1: Run Time (time elapsed from start of engine) can only be shown in and , not in .
XYZ
XY
Z
(See Note 1
below)
Display example
Water Temperature
Voltage
Engine RPM
【Reset the Peak value】
Press the MODE
switch for 3 seconds
during Real-time
display
Press the MODE switch for 3 seconds
during display the Peak value
1
Real-time
display
Display
the Peak value
32
2
1
Display the Peak value
• Reset peak values of all display items.
• Peak readings are reset when the key is turned OFF.
Back to Real-time display
Example of
Single-display
Example of
Multi-display
Display Peak
Reset
the Peak value
Real-time display
Note that display item is different from Communication-system (see page 7 of this manual).
After pressing for 3 seconds, change display item
by each pressing of the UP / DOWN switch during
display blinking.
• For Voltage the lowest, and
the others the highest value
will be displayed.
•The Peak value of motor RPM
is not displayed.
Release
the switch and
no operation
for 5 seconds
(Note)
(Note)

7
8 21
801
531
218
Explanation of each Display Item
Water Temperature
Voltage
Engine RPM
Motor RPM
Vacuum
BOOST
Temperature of the cooling water
Voltage of the battery
Engine Rotation
Motor Rotation of Hybrid car
Negative pressure to the engine
Positive pressure of turbo engine
ExplanationDisplay Item ExplanationDisplay Item
Oil Temperature
Intake Temperature
Run Time
Temperature of the engine oil
Temperature of Intake air to the engine
Elapsed Time from start of engine
(Grasp of the driving time, etc.)
Display Item and Range
Water Temperature
Voltage
Engine RPM
BOOST (Vacuum)
Intake Temperature
Run Time (See Note 1)
Water Temperature
Voltage
BOOST
Oil Temperature
Intake Temperature
Run Time (See Note 1)
Water Temperature
Voltage
Engine RPM
Motor RPM
Run Time (See Note 1)
50 to 110 °C
8.0 to 16.0 V
0 to 8000 rpm
-101 to 100 kPa
0 to 100 °C
---
50 to 110 °C
8.0 to 16.0 V
0 to 200 kPa
70 to 150 °C
0 to 100 °C
---
50 to 110 °C
8.0 to 16.0 V
0 to 8000 rpm
0 to 8000 rpm
---
-35 to 150 °C
8.0 to 18.0 V
0 to 9900 rpm (See Note 2)
-101 to 154 kPa
-35 to 150 °C
---
-35 to 150 °C
8.0 to 18.0 V
0 to 249 kPa
-35 to 150 °C
-35 to 150 °C
---
-35 to 150 °C
8.0 to 18.0 V
0 to 9900 rpm (See Note 2)
0 to 9900 rpm (See Note 2)
---
-35 to 150 °C
8.0 to 18.0 V
0 to 9900 rpm (See Note 2)
-101 to 154 kPa
-35 to 150 °C
0:00 to 9:59 min.
-35 to 150 °C
8.0 to 18.0 V
0 to 249 kPa
-35 to 150 °C
-35 to 150 °C
0:00 to 9:59 min.
-35 to 150 °C
8.0 to 18.0 V
0 to 9900 rpm (See Note 2)
0 to 15000 rpm (See Note 2)
0:00 to 9:59 min.
Display Item
Display Range
Analog Digital
Single-display Multi-display
Note 1: Run Time (time elapsed from start of engine) can only be shown in Multi-display and minimum display unit is 1 min.
Note 2: Minimum display unit is 100 rpm.
1 2 3 4
3
4
3
Communi-
cation
system

8PIVOT CORPORATION 87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 JAPAN
01 86 2
Troubleshooting
If connect the power cable to IGN (The installing car model mentioned in the Compatibility List)
IGN Cable
＝Cut Connector
IGN
(12V with key ON)
OBD Cable Diagnostic
Monitoring
Connector
Yellow Yellow
Red
How to use the Cut Connectors
1
10 mm
2
10 mm
345
Trouble Possible Causes Possible Solutions
Poor connection of each Cable or Con-
nector.
The unit has been installed into an
incompatible car model.
Wrong Communication-system has set.
Reconfirm whether wiring and connec-
tions are correct or not.
Check the “Compatibility List”.
Check the ”Setting Communication
system”.(See page 4 of this manual)
Set communication-system to C.
Self-Adjusting Brightness
【Check the Luminance】(Normally not necessary)
【Connecting】
The battery goes flat on the car
which needs to be set communication-
system C. (Prius ZVW50, etc.)
The communication-system has set
something other than C.
It will return to the normal brightness in
a few minutes when the temperature
in-car dropped.
The display is dark when the
temperature in-car is high on start-up.
The brightness has automatically
adjusted by safety function of the prod-
uct.
The engine has been turned OFF
but the display remain on.
Press the
DOWN switch
during
Single-display
for 3 seconds
1
Real-time display
Display
Luminance
3
2Release the switch
and no operation
for 5 seconds
Daytime (bright)
Nighttime (dark)
Luminance (%)
Ambient
brightness
Under 50
From 50 to 60
Over 60
Luminance (%)
Ambient
temperature (°C)
100% 75% 60% 20%
100 100
75
60
20
When crimping, please
use crimpers or use pliers
to bend and then solder
together.
Peel off of the vinyl
cover at connection.
Peel off of the vinyl
cover at the end of
the product’ s wire.
Wrap around both
wire coils.
Close tightly with
cut connector.
Insulate with vinyl
tape.
Change the wiring to IGN, if the installing car
model mentioned in the Compatibility list or the
display does not lit with engine start sometimes.
Unplug the connector of Red and Yellow cable of
OBD Cable and connect the connector of Yellow
cable to IGN.
Brightness of the display is automatically adjusted under the following conditions.
●Adjustment according to ambient brightness
(reduce nighttime glare)
●Adjustment according to ambient temperature
(prevent the product deterioration)
This product is interlocked with the ECU (engine computer) power. Depending on
the model of car, the display may remain on for up to 3 minutes even after the
engine has been turned off; this is normal.
Does not display with Engine
start.
• Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
• We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar
designs, regulating characteristics, circuitry and circuitry layout.
• We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’ s Manual.
(Note)