Pixio PX274 Prime User manual

The color and the appearance may differ depending on the product, and the specifications are subject to change without prior
notice to improve the performance. The contents of this manual are subject to change without notice to improve quality.
Copyright © 2022 Pixio USA Inc. I Pixio is a registered trademark of Pixio USA Inc. I All Rights Reserved.
Use or reproduction of this manual in parts or entirety without the authorization of Pixio USA Inc is prohibited.
All other trademarks are owned by their respective owners.
PX274 Prime

27in IPS QHD 75Hz Gaming Monitor
PX274P
210316026EMC-1

RISK OF ELECTRIC SHOCK DO NOT OPEN THE MONITOR.
OPENING MONITOR BACK COVER WILL VOID YOUR WARRANTY.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of
this product.
This symbol alerts you that important literature concerning operation
and maintenance has been included with this product.

Before Using the Product.
Do not place the monitor near heat sources, such as radiators, and do not expose the monitor to direct sunlight
for an extended period of time.
Make sure to keep the original packaging material. If there are any needs to transport the monitor, the packaging
material will be the best method for successful delivery.
Make sure to use a soft, non-abrasive cloth when cleaning the monitor. Do not use corrosive or strong detergents
to clean the monitor. They may result in permanent damage to the panel and will void the warranty.
Always check to make sure the power cord is unplugged before cleaning the monitor.
Be careful when handling liquids while cleaning as it may cause irreparable damage to the electrical components
in the monitor.
Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product.
Make sure to allow some space. Do not install near heater or any other high temperature product or humidifier.

Make sure the monitor is not placed near any source of water, such as the bathroom, kitchen, or humid areas.
Do not place the monitor on an unstable, or uneven surface. If dropped, the monitor may cause bodily injuries.
When transporting the monitor, make sure it is secured in an upright position or preferably in its original packaging
for best results. When mounting the monitor, make sure to follow the instructions of the respective mounting provider
for best results.
The openings in the monitor are for ventilation. For best results, make sure the ventilation holes are not covered up.
Avoid confined spaces like a bookcase for proper functionality.
If the monitor will not be used for an extended period of time, make sure to unplug the power cord to prevent the risk
of damage from lighting strikes or other abnormal voltage incidents.
Do not overburden any socket to prevent risk of fire or shock.
Do not stick any foreign objects into the monitor to prevent risk of fire or shock.
Please do not try to take off the back panel to repair the monitor yourself. You may run the risk of shock and void the
warranty as well. Contract Pixio directly for all RMA issues.
Take note of elevation and temperature zone warnings on the adapters.
The icon indicates that the adapter is suited for areas under 2000 meters.
The icon indicates that the adapter is suited for non-tropical areas.

Take the following steps when cleaning.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock
may result.
3 Wipe the monitor with a clean, soft and dry cloth.
Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5 Connect the power cord to the product when cleaning is finished.
6 Power on the product and computer.
Cleaning the Product.

Notice.

Product Includes:
Preparation.

Product Assembly:
1. Assemble the base to the stand with 2 sets of M4 x 16mm screws as pictured.

To remove the whole base, do as above:
Push the Slider on the back cover. Take it out in the arrow pointed direction.
Lift the base.
Product Disassembly:

Net Weight: 4.9kg (10.80lb)
Dimension & Weight.
464.8mm
364.3mm
616mm
410.3mm 251.8mm
57.5mm
100mm
100mm

Monitor Inputs.
*WARNING:
Always use the appropriate power cord.
DC
HDMI2 HDMI 1.4, 60Hz, FreeSync
DP DisplayPort 1.2, 75Hz, FreeSync
Earphone
HDMI1 HDMI 1.4, 60Hz, FreeSync

Control Panel.
UP
DOWN
RIGHTLEFT
Jog Button
Multi directional
button that helps
navigate.
Menu Short Cut
Up Input selection Short Key
Brightness Adjustment Short Key Menu
Volume Adjustment Short Key Menu
Preset selection Short Key Menu
Down
Left
Right
Up Left RightDown
Auto Select
HDMI 2 (1.4)
HDMI 1 (1.4)
DP (1.2)
Preset
User
Standard
Internet
Game
Movie
50
Volume
90
Brightness

Main OSD Navigation
75
Display
Brightness 90
50
Off
Off
Contrast
Preset
DCR
Overdrive
V1.0
E
User
OSD
Exit the Main OSD Menu.
Go Up on the Main OSD Menu / Decrease the value of a selected item.
Go Down on the Main OSD Menu / Increase the value of a selected item.
How to Reconfigure

Display
OSD Menu.
•Brightness: Adjust the display brightness value from 0 to 100.
•Contrast: Adjust the display contrast value from 0 to 100.
•Preset: Select Preset from Standard, User, Internet, Game or
Movie.
•DCR: Turn DCR On or Off.
•Overdrive: Select Overdrive from Off, Low, Middle, and High.
Display
Brightness 90
50
Off
Off
Contrast
Preset
DCR
Overdrive
V1.0
E
User
OSD

Image
•Select Aspect Ratio from Full or 4:3.
MOVE BACK ENTER
Image
Aspect Ratio
V1.0
E
Full
OSD

Color
•Color Temperature: Select Warm, Normal, Cool or User.
•Red, Green, Blue: Adjust color values from 0-100.
•Low Blue Light: Adjust Low Blue Light value from 0-100.
•Black Equalizer: Adjust Black Equalizer value from 0-100.
Color
Color Temp.
Red
Green
Blue
Low Blue Light
Black Equalizer
42
V1.0
E
Normal
45
49
50
0
OSD

OSD Setup
Language
OSD H.Position
OSD V.Position
OSD Timer
Transparency
99
4
15
0
V1.0
E
English
OSD
OSD Setup
•Language: Change the OSD menu display language
•OSD Setup: Select OSD Setup from H Position, V Position,
OSD Timeout, Transparency.
H Position: Adjust 0-100
V Position: Adjust 0-100
OSD Timer: Adjust 15-60
Transparency: Adjust 0-100

System Setup
•Reset: Select Reset from Cancel or Confirm.
System Setup
Reset
V1.0
E
OSD