Pixio PX329 User manual

The color and the appearance may differ depending on the product, and the specifications are subject to change without prior
notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
Copyright © 2019 Pixio USA Inc. I Pixio is a registered trademark of Pixio USA Inc. I All Rights Reserved.
Use or reproduction of this manual in parts or entirety without the authorization of Pixio USA Inc is prohibited.
All other trademarks are owned by their respective owners. Rev.1.01Copyright © 2019 Pixio USA Inc. I Pixio is a registered trademark of Pixio USA Inc.
All Rights Reserved.
PX329

PX329
32in 165Hz Gaming Monitor
180524004EMC-1

RISK OF ELECTRIC SHOCK DO NOT OPEN THE MONITOR.
OPENING MONITOR BACK COVER WILL VOID YOUR WARRANTY.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of
this product.
This symbol alerts you that important literature concerning operation
and maintenance has been included with this product.

Before Using the Product.
Do not place the monitor near heat sources, such as radiators, and do not expose the monitor to direct sunlight
for an extended period of time.
Make sure to keep the original packaging material. If there are any needs to transport the monitor, the packaging
material will be the best method for successful delivery.
Make sure to use a soft, non-abrasive cloth when cleaning the monitor. Do not use corrosive or strong detergents
to clean the monitor. They may result in permanent damage to the panel and will void the warranty.
Always check to make sure the power cord is unplugged before cleaning the monitor.
Be careful when handling liquids while cleaning as it may cause irreparable damage to the electrical components
in the monitor.
Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product.
Make sure to allow some space. Do not install near heater or any other high temperature product or humidifier.

Make sure the monitor is not placed near any source of water, such as the bathroom, kitchen, or humid areas.
Do not place the monitor on an unstable, or uneven surface. If dropped, the monitor may cause bodily injuries.
When transporting the monitor, make sure it is secured in an upright position or preferably in its original packaging
for best results. When mounting the monitor, make sure to follow the instructions of the respective mounting provider
for best results.
The openings in the monitor are for ventilation. For best results, make sure the ventilation holes are not covered up.
Avoid confined spaces like a bookcase for proper functionality.
If the monitor will not be used for an extended period of time, make sure to unplug the power cord to prevent the risk
of damage from lighting strikes or other abnormal voltage incidents.
Do not overburden any socket to prevent risk of fire or shock.
Do not stick any foreign objects into the monitor to prevent risk of fire or shock.
Please do not try to take off the back panel to repair the monitor yourself. You may run the risk of shock and void the
warranty as well. Contract Pixio directly for all RMA issues.
Take note of elevation and temperature zone warnings on the adapters.
The icon indicates that the adapter is suited for areas under 2000 meters.
The icon indicates that the adapter is suited for non-tropical areas.

Take the following steps when cleaning.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock
may result.
3 Wipe the monitor with a clean, soft and dry cloth.
Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5 Connect the power cord to the product when cleaning is finished.
6 Power on the product and computer.
Cleaning the Product.

Notice.

Product Includes:
Preperation.

Product Assembly:
Attached Rand Llegs to the center stand piece.
Secure leg with 2 screw (A) each.
Insert stand to rear of monitor. Secure stand with 1 screw (B)
to complete the stand.

PX329 Vesa Plate Installation:
1. Remove and detach default stand.

2. Remove rear plastic cover around the default stand joint.
3. Uninstall default stand joint by removing 4 screw sets around the joint.

4. Place VESA Plate on top of the plastic cover area.

5. Use default stand joint screw
set and install VESA Plate.

6. Install VESA Mount with provided
VESA Screw set.

Dimension & Weight.

Monitor Inputs.
DC
HDMI1 HDMI 2.0
HDMI2 HDMI 2.0
DisplayPort1.2 [DP1] 165Hz
DisplayPort1.2 [DP2] 144Hz
AUDIO OUT
NOTICE: Use a DisplayPort 1.2 Cable with FreeSync turned off, for 165Hz refresh rate. HDMI will not reach 165Hz.

Menu Short Cut
Up Input selection Short Key / Exit Short Key Menu
Volume Adjustment Short Key Menu
Game Assist selection Short Key Menu
Preset selection Short Key Menu
Down
Left
Right
Control Panel.
MOVE BACK ENTER
Input
Auto Select
DP1
DP2
HDMI1
HDMI2
Up
MOVE BACK ENTER
Game Assist
Timer
Crosshair
FPS Counter
Left
MOVE BACK ENTER
Preset
Standard
User
Movie
Photo
RTS
FPS1
FPS2
Right
MOVE BACK ENTER
Volume
50
Down
Jog Button
Multi directional
button that helps
navigate.
UP
DOWN
RIGHTLEFT

Main OSD Navigation
Move the OSD Menu FPS
MOVE BACK ENTER
2560x1440 60Hz Freesync
60
90
Contrast
Black Equalize
Preset
Aspect Ratio
Sharpness
Ultra vivid
Color
Gaming Setup
Input
System Set
User Data
V2.0
Brightness
Display
How to Reconfigure
To turn ON/OFF the OSD Menu, Press Jog Button.
Up
Down
Left
Right
Press
Move up the OSD Menu / Increase
Move down the OSD Menu / decrease
Move left on the OSD Menu / Back
Move right on the OSD Menu / Enter
Turn ON / OFF the OSD Menu
BACK
ENTER
V2.0

Display
OSD Menu.
FPS
MOVE BACK ENTER
2560x1440 60Hz Freesync
60
90
Display
Contrast
Black Equalize
Preset
Aspect Ratio
Sharpness
Ultra vivid
Color
Gaming Setup
Input
System Set
User Data
Brightness
•Brightness: Adjust the display brightness value from 0 to 100.
•Contrast: Adjust the display contrast value from 0 to 100.
•Black Equalize: Adjust the Black Equalize value from 0 to 100.
•Preset: Select Preset from Standard, User, Movie, Photo, RTS,
FPS1, and FPS2.
•Aspect Ratio: Select Aspect Ratio from Full, 16:9, and 4:3.
•Sharpness: Adjust the Sharpness value from 0 to 100.
•Ultra vivid: Turn Ultra vivid On or Off.
V2.0