Planet Networking & Communication HZS-532E-DE User manual

Z-Wave Smart Energy Meter
HZS-532E-DE/HZS-531A-US

Z-Wave Smart Energy Meter
HZS-530 Series
- 2-
Copyright
Copyright ©2015 by PLANET Technology Corp. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for
any particular purpose. Any software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer (and not PLANET,
its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and
any incidental or consequential damages resulting from any defect in the software. Further,
PLANET reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches)
during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer
manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

Z-Wave Smart Energy Meter
HZS-530 Series
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of
the presence of hazardous substances in electrical and electronic equipment, end
users of electrical and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
User’s Manual of PLANET Z-Wave Smart Energy Meter
Model: HZS-532E-DE / HZS-531A-US
Rev: 1.00 (October, 2015)
Part No. EM-HZS-530 Series_v1.0.doc
- 3-

Z-Wave Smart Energy Meter
HZS-530 Series
- 4-
Table of Contents
Chapter 1. Product Introduction ......................................................................5
1.1 Package Contents...............................................................................5
1.2 Overview.............................................................................................5
1.3 Specifications......................................................................................7
Chapter 2. Hardware Interface........................................................................8
Chapter 3. Z-Wave Device Setting................................................................ 10
3.1 Configuring Z-Wave Device via Web ................................................10
3.2 Configuring Z-Wave via Smart Phone...............................................13
3.3 Configuring Z-Wave via HTS-1000P.................................................19
Appendix A: Troubleshooting & Frequently Asked Questions.......................28

Z-Wave Smart Energy Meter
HZS-530 Series
Chapter 1. Product Introduction
1.1 Package Contents
The package should contain the following:
zEnergy Meter x 1
zQuick Installation Guide x 1
If any of the above items are missing, please contact your seller immediately.
1.2 Overview
Home Automation and Smart Home Control
The HZS (Z-Wave Sensing Device) series of PLANET Home Automation product family,
based on Z-Wave technology, provides the advanced security system that protects your home
and family 24/7. Easy operation and flexible configuration are the attractive features of our
system; the simple one-touch button lets you program your regular settings according to your
preference and operation mode. Worked with PLANET HAC-1000 Z-Wave Home Automation
Control Gateway, you get the all-round and reliable home security services that we offer. Our
full range of product lines ensure that you get all the devices you need for your home security
system.
- 5-

Z-Wave Smart Energy Meter
HZS-530 Series
Energy and Cost Saving on Every Room
PLANET HZS-530 series is a Z-Wave Smart Energy Meter that checks the current energy
consumption in your home within the configuration interface of the HAC-1000. You can also
manage these energy-saving devices such as power meter switches, power switches and
dimmer switches to help you reduce energy consumption and thus save expenses on utilities.
Scheduled Power On/Off
The HZS-530 series Energy Meter allows you to pre-define a power schedule for home
devices via the HAC-1000 Control Gateway. It alerts users to an upcoming shutdown, and
then waits a predefined amount of time to allow users to finish their work and sign off. For
example, you can define a schedule that would shut down your home device on Friday night,
and start it again Monday morning.
Getting Started is as Easy as 1-2-3
1.Via the Cloud Home App (including Home Automation Controller Pad and Control
Gateway): Press Inclusion/Exclusion to include/exclude Z-Wave device.
2.On the Z-Wave device: Press the Pair button to establish a connection with the control
gateway.
3.Users can enjoy and manage Z-Wave network right away.
Overload Protection
The HZS-530 series Energy Meter is a miniature device that allows you to control the amount
of electricity consumed. If the current exceeds 10 amps, the circuit breaker will open up,
cutting off any more current flow. Furthermore, the HZS-532E-DE, an ETSI compliant product
in the HZS-530 series, could inform you about the current load of the connected appliances by
changing in color of its built-in LED.
- 6-

Z-Wave Smart Energy Meter
HZS-530 Series
- 7-
1.3 Specifications
Product HZS-531A-US HZS-532E-DE
Hardware and Network
Z-Wave Frequency America: 908.42MHz Europe: 868.42MHz
LED Indicators
Power On/Off: red/green
Z-Wave RF transfer/receive: red/green (flash)
Energy level: green/orange/red
Buttons 1 x Power On/Off button (Either control manually or remotely via
the control gateway)
Load 110V, 10A, 1100W (resistive)
220V, 10A, 2200W (resistive)
Operating Range Up to 30 meters in open space
Installation Plug connection for indoor use
General
Power Requirements AC 100V~230V
Operating Temperature 15 ~ 60 degrees C
Operating Humidity 10 ~ 90% (non-condensing)
Weight 156g 126g
Dimensions 100 x 62 x 38 mm (W x D x H) 61 x 58 mm (Φx L)
Emission CE, FCC

Z-Wave Smart Energy Meter
HZS-530 Series
Chapter 2. Hardware Interface
Model HZS-531A-US
Dimensions (W x D x H) 100 x 62 x 38 mm
Weight 156g (gross weight)
Interface Description
AC outlet Connect a device to power outlet to supply power to it.
Program switch 1) Press to include or exclude a Z-Wave network.
2) Switch Power on and off.
Z-Wave outlet
This outlet is used to plug in the device you wish to monitor, such as
a lamp. Do not exceed the loading of wattage more than 10A when
connecting to an electronic appliance.
Plug Plug the Energy Meter into any available wall outlet.
- 8-

Z-Wave Smart Energy Meter
HZS-530 Series
Model HZS-532E-DE
Dimensions (Φx L) 61 x 58 mm
Weight 126g (gross weight)
Interface Description
LED
Power On/Off: Red/Green
Z-Wave RF transfer/receive: Red/Green (Flash)
Energy level: Green/Orange/Red
Color Current
Green 0 ~ 3 AMP
Orange 3 ~ 7 AMP
Red 7 ~ 10 AMP
Program switch 1) Press to include or exclude a Z-Wave network.
2) Switch Power on and off.
Z-Wave outlet
This outlet is used to plug in the device you wish to monitor, such as
a lamp. Do not exceed the loading of wattage more than 10A when
connecting to an electronic appliance.
Plug Plug the Energy Meter into any available wall outlet.
- 9-

Z-Wave Smart Energy Meter
HZS-530 Series
Chapter 3. Z-Wave Device Setting
3.1 Configuring Z-Wave Device via Web
Please refer to the following steps to add Z-Wave device via web.
Step 1. Include a Z-Wave device via web.
a) Go to "Z-Wave" and click "Device
Configuration".
b) Click “Include New Device” and the
screen will appear with "Add Device:
Waiting for a user action."
c) Press the program switch button 3
times within 2 seconds on the
Z-Wave device to connect.
d) If your device has successfully been added, it will show "Add Device: Command has
been completed successfully".
If the device didn’t add successfully, please place the device next to the
gateway and try again.
- 10 -

Z-Wave Smart Energy Meter
HZS-530 Series
Step 2. Set up the location and room for Z-Wave device via web.
a. Create rooms in your environment.
b. Edit device.
Step 3. Create a scene via web.
a. Click “Create Scene” and name new scene.
b. Select a device from this scene.
- 11 -

Z-Wave Smart Energy Meter
HZS-530 Series
c. Select ON or OFF from this scene.
d. You can click “RUN” to run this scene.
Step 4. Create trigger via web.
a. Click “Create a Trigger” and name
new trigger.
b. Select a Z-Wave device for this
trigger.
c. Select when it triggers, it will alarm or
bypass.
d. Select when it triggers, it will run
which scene.
- 12 -

Z-Wave Smart Energy Meter
HZS-530 Series
After entering the time selected for the scene to trigger, tick “Save and send alarm notification”.
Tick “Active” to enable this trigger.
3.2 Configuring Z-Wave via Smart Phone
The HAC-1100 can be used on iOS and Android operating system. Cloud Home can be
downloaded at Google Play store or app store.
Please refer to the following steps to install Cloud Home app and add Z-Wave device via smart
phone.
Step 1. Include a Z-Wave device via smart phone (Android/iOS).
a. Register a user account.
b. Setting
- 13 -

Z-Wave Smart Energy Meter
HZS-530 Series
c. Inclusion/Exclusion
d. Click Inclusion to add device.
e. e. Press the program switch button
3 times within 2 seconds on the
Z-Wave device to connect.
- 14 -

Z-Wave Smart Energy Meter
HZS-530 Series
Step 2. Set up the location and room for Z-Wave device.
a. Create rooms in your environment.
b. Click “No Room” and will show the
device. And place the new devices
in a room.
c. Select “Name” to name this device
and select “Location” to place this
device in the room that you created.
d. Select Picture for your Z-Wave
device.
- 15 -

Z-Wave Smart Energy Meter
HZS-530 Series
e. Click “Back” to save.
f. Done successfully.
- 16 -

Z-Wave Smart Energy Meter
HZS-530 Series
Step 3. Create a scene via smart phone.
a. Click “Add” and name a new scene.
b. Click “Add” to add a Z-Wave device.
c. Select a Z-Wave device.
d. Click ON or OFF for the device you
select.
e. Click “Back” to save.
f. Done successfully.
- 17 -

Z-Wave Smart Energy Meter
HZS-530 Series
Step 4. Create Trigger via smart phone.
a. Click “Add”.
b. Name this new Trigger.
c. Select the Z-Wave device and click
next.
d. Select a mode for a Z-Wave device.
e. Select a scene.
f. Select the time for the trigger and
which scene to run.
g. Done successfully.
h. If you enable Save and send alarm
notification, when it triggers, it will
have a log. You can check this in
Notification History.
- 18 -

Z-Wave Smart Energy Meter
HZS-530 Series
3.3 Configuring Z-Wave via HTS-1000P
Step 1. Fill out the IP of control gateway to connect with gateway.
Click the “Gateway”
button.
Click the magnifying
glass to search the IP of
gateway.
Control pad found an IP
of gateway. Click the IP
to join.
- 19 -

Z-Wave Smart Energy Meter
HZS-530 Series
- 20 -
The default gateway port
is 5000, and user name
and password are both
admin.
Step 2. Include a Z-Wave device via HTS-1000P.
Click the “Z-Wave
devices” button to add
Z-Wave devices to
gateway.
Click the “Include New
Device” button to add
Z-Wave device.