Planet VIP-156 User manual

1
User’s Manual
VoIP Analog Telephone Adapter
VIP-156/VIP156PE/VIP-157/VIP-157S

Copyright
Copyright (C) 2012 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology, This
User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording,
or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without
the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
2
parately.
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE se
Trademarks
The PLANET logo is a trade mark of PLANET Technology. This documentation may refer to numerous hardware
and software products by their trade nam es. In most, if not all cases, their respectiv e companies claim these
designations as trademarks or registered trademarks.

3
Revision
User’s Manual for PLANET VoIP Analog Telephone Adapter:
Model: VIP-156 / VIP156PE / VIP-157 / VIP-157S
Rev: 5.0 (2012, March)
Part No. EM-VIP_ATA_V5.0

4
TABLE OF CONTENTS
UChapter 1 IntroductionU............................................................................................................6
UOverviewU......................................................................................................................................................6
UPackage ContentU..........................................................................................................................................7
UPhysical DetailsU............................................................................................................................................7
ULED Display & ButtonU......................................................................................................................10
UChapter 2 Preparations & InstallationU................................................................................12
UPhysical Installation RequirementU...........................................................................................................12
ULAN IP address configuration via web configuration interfaceU.........................................................13
UChapter 3 Network Service ConfigurationsU........................................................................17
UConfiguring and monitoring yourATAfrom web browserU...................................................................17
UOverview on the web interface of ATAU..............................................................................................17
UManipulation of ATA via web browserU..............................................................................................17
UChapter 4 VoIPTelephone Adapter ConfigurationsU...........................................................19
UStatusU.................................................................................................................................................19
UPhone BookU........................................................................................................................................20
UCall ServiceU........................................................................................................................................22
USNTP settingsU....................................................................................................................................24
UVolume SettingU...................................................................................................................................24
UDail Plan SettingU................................................................................................................................25
UGeneralU...............................................................................................................................................29
UChapter 5 NetowrkU.................................................................................................................31
UNetwork SettingsU...............................................................................................................................31
UDDNS SettingsU...................................................................................................................................32
UVLAN SettingsU..................................................................................................................................32
UVPN SettingsU.....................................................................................................................................33
UIPV6 SettingsU.....................................................................................................................................34
UChapter 6 NAT TransU.............................................................................................................35
UStun SettingsU......................................................................................................................................35
UPC SettingsU........................................................................................................................................35
UDMZ and MAC CloneU.......................................................................................................................36
UVirtual ServerU.....................................................................................................................................36
UChapter 7 SIP SettingU............................................................................................................38
UService Domain SettingsU....................................................................................................................38
UCodec SettingU.....................................................................................................................................39
USIPAdvance SettingU..........................................................................................................................40
UChapter 8 Advance SettingU....................................................................................................44
UStatus LogU..........................................................................................................................................44

5
UAuto ConfigU.......................................................................................................................................44
UManagement-Advanced SettingU.........................................................................................................45
UTonesU..................................................................................................................................................47
UTR-069U...............................................................................................................................................47
UChapter 9 Other SettingU........................................................................................................49
USystem AuthorityU...............................................................................................................................49
UFirmware UpgradeU.............................................................................................................................49
UAuto Update SettingsU.........................................................................................................................50
UReset to defaultU..................................................................................................................................52
USave and RebootU................................................................................................................................52
ULogoutU................................................................................................................................................52
UAppendix A Voice Communication SamplesU........................................................................................53
UCase 1: ATA to ATA connection via IP addressU..................................................................................53
UCase 2: (Peer-to-Peer mode) VIP-157S Port 1 to Port 2 communicationsU.........................................54
UCase 3: Call Forward Feature_Example 1U.........................................................................................55
UCase 4: Call Forward Feature_Example 2U.........................................................................................56
UCase 5: Call Forward Feature_Example 3U.........................................................................................57
UCase 6: Call Forward Feature_Example 4U.........................................................................................58
UCase 7: Auto Answer Feature_IP to PSTNU........................................................................................58
UCase 8: Auto Answer Feature_PSTN to IPU........................................................................................60
UAppendix B The method of operation guideU...........................................................................................62
UCall TransferU......................................................................................................................................62
U3-Way ConferenceU.............................................................................................................................62
UCall WaitingU.......................................................................................................................................62
USwitch the Realm (Registration Proxy Server)U..................................................................................62
UAuto Update firmware by manual (Keypad)U......................................................................................63
UAppendix C VIP-156/VIP-156PE/VIP-157/VIP-157S SpecificationsU....................................................64

1
0BChapter 1
1BIntroduction
11BOverview
Based on years of VoIP manufacturing experiences, PLANET Technology VoIP total solutions are
known for advanced implementation of standards based telephony with mass deployment capability.
Cost-effective, easy-to-install and simple-to-use, the PLANET VIP-156/VIP-157/VIP-157S VoIP Phone
Adapter (“ATA” in the following term) converts standard telephones to IP-based networks. The service
providers and enterprises offer users traditional and enhanced the telephony communication services
via the existing broadband connection to the Internet or corporation network.
With the ATA, home users and companies are able to save the installation cost and extend their past
investments in telephones, conference and speakerphones. The ATA can be the bridge between
traditional analog systems and IP network with an extremely affordable investment.
The ATA includes two alternatively Ethernet interface for Internet (PPPoE, DHCP or Fixed IP), or office
LAN connection. With adding the auto-provision feature of our IP PBX product - IPX-2000, the ATA can
be seamlessly integrated into the telephony network and be used in consumer and business IP
telephony service, no expertise required!
The ATA and our IP PBX system integration are the ideal combination for your office daily
communications.
Product Features
• Feature-rich telephone service over home or office Internet/Intranet connection
• Auto-config feature for flexible, ease-of-use IP PBX system integration
• Cost effective, field proven compatibility, and stability
• Web-based and telephone keypad machine configuration
• Remote machine administration authentication
• Voice prompt for machine configurations
VoIP Features
• SIP 2.0 (RFC3261) compliant
• Peer-to-Peer / SIP proxy calls
• Voice codec support: G.711, G.723.1, G.729A/G.729B
• T.38 FAX transmission over IP network
6

• Voice processing: Voice Active Detection, DTMF detection/ generation, G.168 echo cancellation
(16mSec.), Comfort noise generation (CNG)
• In band, out-of-band, and SIP-info DTMF support
• IPV6 Support
• TR-069
12BPackage Content
The contents of your product should contain the following items:
VoIP Telephone Adapter
Power adapter
Quick Installation Guide
User’s Manual CD
RJ-11 cable x 1
13BPhysical Details
The following figure illustrates the front/rear panel of ATA.
Respective model/descriptions are shown below:
VIP-156: SIP Analog Telephone Adapter
VIP-156PE: 802.3af PoE SIP Analog Telephone Adapter
VIP-157: 1 FXS/ 1 FXO SIP Analog Telephone Adapter
VIP-157S: 2-port FXS SIP Analog Telephone Adapter
Front Panel of VIP-156
7

Left / Right Panel of VIP-156
Front Panel of VIP-156PE
Left / Right Panel of VIP-156PE
8

Front Panel of VIP-157
Left / Right Panel of VIP-157
Front Panel of VIP-157S
9

Left / Right Panel of VIP-157S
19BLED Display & Button
1 PC RJ-45 connector, to main tain the existing network structure,
connected directly to the PC through straight CAT-5 cable
2 LAN
RJ-45 connector, for Inte rnet access, connected directly to
Switch/Hub through straight CAT-5 cable.
The LAN interface also can be connected with 802.3af PoE
switch or converter for power supply (VIP-156PE)
3 12V DC 12V DC Power input outlet
4 Reset
Reset to the factory default setting
ÍNote Machine default IP is http://192.168.0.1. Press RESET
button on rear panel over 5 seconds will reset the VoIP Phone
Adapter to factory default value. (Except speed dial and
call forward settings)
10

11
LED display of VIP-156 / VIP-156PE
LED display of VIP-157 / VIP-157S
ED Indicators DeLscriptions
PWR Power is supplied to the device.
STATUS The Status LED will be flashing when the machine is operational
LNK/ACT
cted to LAN at 100Mb/s.
OFF: the device is connected to LAN at 10Mb/s.
ON: the device is conne
RING
).
Blinking: the phone is ringing.
OFF: the phone is idle.
ON: the phone is in use (offhook
LED Indicators Descriptions
STATUS The Status LED will be flashing when the machine is operational
LNK/ACT
cted to LAN at 100Mb/s.
OFF: the device is connected to LAN at 10Mb/s.
ON: the device is conne
RING 1
).
inging.
OFF: the phone is idle.
ON: the phone is in use (offhook
Blinking: the phone is r
RING 2
).
Blinking: the phone is ringing.
OFF: the phone is idle.
ON: the phone is in use (offhook

2
2BChapter 2
Preparations & Installation
14BPhysical Installation Requirement
This chapter illustrates basic installation of ATA analog Phone Adapter ((“ATA” in the following term))
• Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.
• TCP/IP protocol must be installed on all PCs.
For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem
Administration Interface
PLANET ATA provides GUI (Web based, Graphical User Interface) for machine management and
administration.
Web configuration access
To start ATA web configuration, you must have one of these we b browsers installed on computer for
management
• Microsoft Internet Explorer 6.0.0 or higher with Java support
Default LAN interface IP addre ss of ATA is 192.168.0.1. You may now o pen your web browser, and
insert HUhttp://192.168.0.1UH in the address bar of web browser to logon ATA web configuration page.
ATA will prompt for logon user name/password, please enter: root /null (no password) to continue
machine administration.
12

Please locate your PC in the same network segment
(192.168.0.x) of ATA. If you’re not familiar with TCP/IP,
please refer to related chapter on user’s manual CD or
consult your network administrator for proper network
configurations.
ÍNote
20BLAN IP address configuration via web configuration interface
Execute your web browser, and insert the IP address (default: 192.168.0.1) of VIP in the address bar.
After logging on machine with username/password (default: root / no password), browse to “Network”
--> “Network Settings” configuration menu:
) of VIP in the address bar.
After logging on machine with username/password (default: root / no password), browse to “Network”
--> “Network Settings” configuration menu:
Parameter Description
IP address LAN IP address of ATA
Default: 192.168.0.1
Subnet Mask LAN mask of ATA
Default: 255.255.255.0
Default Gateway Gateway of ATA
Default: 192.168.0.254
Network settings via Keypad commands
The ATA series phone adapters support telephone keypad configurations, please connect analog
telephone set and refer to the following table for machine network configurations.
When you want to run the setup or the start function, it
LHint
must unlock the protect function #190# before set up network
settings and ATA function via keypad..
13

14
IVR Menu Choice Machine operation Parameter(s) Notes:
#111# Set DHCP client None
ATA will change to DHCP
Client
#112xxx*xxx*xxx*
xxx# Setup Static IP Address
Use the * (star) key
when entering a decimal
point.
DHCP will be disabled and
system will change to the
Static IP type.
#113xxx*xxx*xxx*
xxx# Set Network Mask
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#114xxx*xxx*xxx*
xxx# Set Gateway IP Address
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#115xxx*xxx*xxx*
xxx# Set Primary DNS Server
Use the * (star) key
when entering a decimal
point.
Must set Static IP first.
#190# Unlock None
Must unlock the protect
function before set up
network settings and ATA
function via keypad.
#191# Lock None
The system will be lock
and can’t set up network
settings via keypad.
#195# Reboot None
The system will reboot
automatically.
#198# Factory Reset None
The system will be reset to
factory default value and
reboot automatically.
0＊To switch PSTN mode None VIP-157 only
Following keypad commands can be used to display the network settings enabled on ATA via voice
prompt.
IVR Menu Choice Machine operation Notes:
#120# Check PC IP Address
IVR will announce the current PC-port IP
address of the ATA.
#121# Check network connection Type
IVR will announce if DHCP in enabled or
disabled.
#122# Check the Phone Number
IVR will announce current enabled VoIP
number.
#123# Check Network Mask IVR will announce the current network mask

15
of the ATA.
#124# Check Gateway IP Address
IVR will announce the current gateway IP
address of the ATA.
#125# Check Primary DNS Server Setting
IVR will announce the current setting in the
Primary DNS field.
#126# Check LAN IP Address
IVR will announce the current LAN port IP
address of the ATA.
#128# Check Firmware Version
IVR will announce the version of the
firmware running on the ATA.
Following keypad commands can be used to set up the main function .
IVR Menu Choice Machine operation Parameter(s) Notes:
#138# Enable call waiting None Enable Call waiting
#139# Disable call waiting None Disable Call waiting
#160# Update firmware None Update firmware
#510# Blind Transfer ATA Bland Transfer
#511# Attendant Transfer ATA Attendant Transfer
#512# 3-way calling ATA 3-way calling
#514# IP transfer to PSTN
ATA transfer IP call to
PSTN side
#130+[1~8]# Set Codec
1:G.711 u-Law, 2: G.711
a-Law, 3: G.723.1, 4:
G.729a, 5: G.726 16K, 6:
G.726 24K, 7: G.726
32K, 8: G.726 40K,
You can set the codec you
want to the first priority.
#131+[00~15]# Set Handset Gain
Handset Gain from
0~15
You can set the Handset
gain to proper value,
default is 10
#132+[00~12]# Set Handset Volume
Handset Volume from
0~12
You can set the Handset
volume to proper value,
default is 10
#135xxx*xxx*xxx*
xxx# TFTP Server IP Address
Set Auto config TFTP
Server IP Address
You can set the TFTP
Server IP address
#136xxx*xxx*xxx*
xxx# FTP Server IP Address
Set Auto config FTP
Server IP Address
You can set the FTP
Server IP address
#137+[0~2]# Auto config mode
0: Disable, 1: TFTP
mode, 2: FTP mode
You can set the Auto
configuration mode, 0:
Disable, 1: use TFTP
Server, 2: user FTP Server

#145# Forward function disable Disable forwrad funciton
#146+Number# enable forward to FXS
Port
Eanble forward to FXS
Port
#147+Number# enable forward to FXO
Port
Eanble forward to FXO
Port
#116# Enable PPTP function None Enable PPTP function
#117# Disable PPTP function None Disable PPTP function
#118# Enable VLAN function None Enable VLAN function
#119# Disable VLAN function None Disable VLAN function
Please contact your Internet service provider to obtain the
16
Internet access type, and select the proper network settin
in ATA to establish the network connections.
gs
LHint
After confirming the modification you’ve done, Please click on the Submit button to apply settings and
browse to “Save & Reboot” menu to reboot the machine to make the settings effective.
Connection Type Data required.
Fixed IP In most circumstances, it is no need to configure the DHCP settings.
DHCP clinet The ISP will assign IP Address, and related information.
PPPoE The ISP will assign PPPoE username / password for Internet access,
Please consult your ISP personnel to obtain proper PPPoE/IP
address related information, and input carefully.
LHint If Internet connection cannot be established, please check
the physical connection or contact the ISP service staff
for support information.
Save Modification to Flash Memory
Most of the VoIP router parameters will take effective after modifications, but it is just temporary stored
on RAM only, it will disappear after your reboot or power off the VoIP Phone Adapter, to save the
parameters into Flash ROM and let it take effective forever, please remember to press the Save &
Reboot button after you modify the parameters.

3
3BChapter 3
Network Service Configurations
15BConfiguring and monitoring your ATA from web browser
The ATA integrates a web-based graphical user interface that can cover most configurations and
machine status monitoring. Via standard web browser, you can configure and check machine status
from anywhere around the world.
21BOverview on the web interface of ATA
With web graphical user interface, you may have:
 More comprehensive setting feels than traditional command line interface.
 Provides user input data fields, check boxes, and for changing machine configuration settings
 Displays machine running configuration
To start ATA web configuration, you must have one of these web browsers installed on computer for
management
 Microsoft Internet Explorer 6.0.0 or higher with Java support
22BManipulation of ATA via web browser
Log on ATA via web browser
After TCP/IP configurations on your PC, you may now open your web browser, and input
HUhttp://192.168.0.1UH to logon Phone Adapter web configuration page.
Phone Adapter will prompt for logon username/password: root / null (no password)
ATA log in page
When users login the web page, users can see the Phone Adapter system information like firmware
version, company…etc in this main page.
17

VoIP Phone Adatper main page
18

19
4BChapter 4
5BVoIP Telephone Adapter Configurations 4
23BStatus
Show all the system information, ex: WAN/LAN IP address, System information, IPV6 connection
information, Register status and VPN connection message. (After you setup the VPN line then the
status will start to show out)

24BPhone Book
ATA can set up 140 records of Phone Book. User can dial the Name records to make calls via Phone
Book feature.
Field Description
Phone Book Page The default is Page 1. It can select Page1 ~ Page 7 to
look round Phone Book records.
Phone The record number from 1 ~ 140, it can set up 140
20