Planet ICG-2515 Series User manual

Industrial 5G NR Cellular Gateway
ICG-2515 Series
Quick Installation Guide

Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 4
3. Hardware Installation................................................................. 5
3.1 SIM Card Installation .......................................................... 5
3.2 5G NR Antenna Installation ................................................. 6
3.3 Wi-Fi Antenna Installation (Wi-Fi model) ............................... 7
3.4 Wiring the Power Inputs...................................................... 8
3.5 Grounding the Device.......................................................... 9
3.6 Wiring the Fault Alarm Contact ...........................................10
4. Starting Web Management ........................................................11
4.1 Logging in to the Cellular Gateway......................................12
5. RecoveringBackto DefaultConguration ...................................14
6. Customer Support ....................................................................15

3
1. Package Contents
Thank you for purchasing PLANET Industrial 5G NR Cellular Gateway,
ICG-2515 series. The hardware specications of these models are as
follows:
Model Name RJ45 Fiber Wi-Fi
ICG-2515-NR 5 - -
ICG-2515W-NR 5 - 11ax
ICG-2515F-NR 4 1 -
ICG-2515FW-NR 4 1 11ax
“Cellular Gateway” is used as an alternative name in this Quick
Installation Guide.
Open the box of the Cellular Gateway and carefully unpack it. The
box should contain the following items:
zIndustrial 5G NR cellular gateway x 1
zQuick installation guide (QR code) x 1
zPLANET CloudViewer QIG x 1
zWall-mount plate w/screw x 1 set
z5G NR antenna x 4
z5G NR antenna extender with magnetic base x 4
zOther component, as below:
Model Name RJ45 dust
cap
SFP dust
cap
Dual band
Wi-Fi antenna
Antenna
dust cap
ICG-2515-NR 6 - - 4
ICG-2515W-NR 6 - 2 6
ICG-2515F-NR 5 1 - 4
ICG-2515FW-NR 5 1 2 6
If any item is found missing or damaged, please contact your local
reseller for replacement.

4
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS
X or later, Linux, UNIX, or other platforms are compatible with TCP/
IP protocols.
zWorkstations are installed with Ethernet NIC (Network Interface
Card).
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser.
Note
It is recommended to use Chrome 98.0.xxx or above to
access the Cellular Gateway. If the Web interface of the
Cellular Gateway is not accessible, please turn off the
anti-virus software or firewall and then try it again.

5
3. Hardware Installation
Refer to the illustration and follow the simple steps below to quickly
install your Cellular Gateway.
3.1 SIM Card Installation
A. Insert an ejector pin into the yellow button next to the tray to
loosen the tray.
SIM1
B. Pull out the tray gently from the tray slot. Place the SIM card on the
tray with the gold-colored contacts facing upwards.
C. Insert the tray back into the tray slot.
zA mini SIM card with 5G NR and 4G LTE subscription

6
3.2 5G NR Antenna Installation
Step 1: Connect 5G NR antennas to the 5G NR antenna extender.
Four SMA female
connectors
ANT1 ANT3
ANT2
Cellular
ANT4
Step 2: Fasten the 5G NR antenna extenders to the connectors.

7
3.3 Wi-Fi Antenna Installation (Wi-Fi model)
Step 1: Fasten the two dual-band antennas to the antenna
connectors on the front panel of the Cellular Gateway.
Step 2: Youcan bendtheantennastotyouractualneeds.
Two Wi-Fi
RP-SMA Connectors
Reset
SIM1
SIM2
RS485
P2P1 Alarm I/O
2.4G 5GSIM1 SIM2
ICG-2515FW-NR
WAN/LAN
LAN
SFP
H
L
Cellular
Signal
5G
5
3
1
4
2
1000
10/100
LNK/
ACT
Wi-Fi
Wi-Fi
Note
Please use PLANET dual-band Wi-Fi antenna for high effi-
ciency to avoid low efficacy.

8
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Cellular
Gateway is used for two redundant power inputs. Please follow the
steps below to insert the power wire.
Caution
When performing any of the procedures like inserting the
wires or tightening the wire-clamp screws, make sure the
power is OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1 and 2
for POWER 1, or 5 and 6 for POWER 2.
Max. Fault Alarm Loading: 24V, 1A
DI1 DO0 DO1DI0 GNDGND
ANT1 ANT3
ANT2
Cellular
ANT4
V1+ V2+
PWR1 PWR2Alarm
DC Input: 9-54V , 1.5A max.
AC Input: 24V
, 1A max.
1 2 3 4 5 6
1 2 3 4 5 6
Note
Please make sure the input voltage is under the specifica-
tions of the Cellular Gateway.

9
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
Power 1 Alarm Power 2
+ - + -
Note
The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
Caution
PWR1 and PWR2 must provide the same DC voltage
while operating with dual power input.
3.5 Grounding the Device
User MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.

10
3.6 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the Cellular
Gateway will detect the fault status of the power failure or port failure,
and then will form an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Alarm
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V (max.) and 1A
current.